advertisement
Item Number: A03330
We are here to help: [email protected]
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
1.
We suggest installation by a licensed electrician .
2.
Please read the instruction carefully and save it as you may need it at later time.
3.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “ OFF ” position. B). Place the wall switch in the “ OFF ” position.
4.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5.
Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6.
Make sure the voltage you are using is 120V . The maximum wattage is 60W per bulb.
7.
Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8.
When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT ：
www.lnchome.com
Page:
‐ 1 ‐
/
3
TOOLS REQUIRED (NOT INCLUDED):
We are here to help: [email protected]
Before doing assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING:
(A) Anchor (2)
(B)Mounting plate (1)
(C)Green ground screw (1)
(F) Tapping screw (2)
(G) Back plate (1)
(H) Knob nut (2)
( I ) Ceramic socket (3)
(J) Glass shade (3)
(K) Socket ring (3)
(L) Spacer tool (1)
ACCESSORIES ENCLOSED:
(E) Mounting screw (2)
(D)Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1.
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
2. Turn off power
3. Make assembly
www.lnchome.com
Page:
‐ 2 ‐
/
3
We are here to help: [email protected]
Step A1: Unscrew the knob nut(F) from back plate(G) then gently remove mounting plate (B)
Step A2: Secure back plate (B) to outlet box with outlet box screws (E), plastic wall anchors (A) and wood screws (F).
Step A3: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT
WIRE TO GROUND WIRE
Connect ground wire according to below chart Connect wires according to below chart
Twist plastic wire connector until wires are tightly joined together,wrap each connector with approved electrical tape and
carefully tuck all wires into the outlet box
Step A4: Put the back plate (G)on the screws and secure them with ball nut(F)
Step A5: Remove socket ring (K) from socket with spacer tool (L). Then position glass shade (J) on socket (I). And secure with socket ring (K).
Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.)
4. Check everything installed proper, then you could turn on the light.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
www.lnchome.com
Page:
‐ 3 ‐
/
3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement