Rust-Oleum Parks 258687 1 gal. Water-Base Sanding Sealer (4-Pack) Use and Care Manual

Rust-Oleum Parks 258687 1 gal. Water-Base Sanding  Sealer (4-Pack) Use and Care Manual
TECHNICAL DATA
PKS-07
PRO FINISHER
WATER-BASED SANDING SEALER
.DESCRIPTION AND USES
.
.PRODUCT APPLICATION
Pro Finisher Water-based Sanding Sealer is a fast-drying, highperformance sealer designed for use under Pro Finisher Waterbased Polyurethane where a clear, colorless finishing system is
desired. Pro Finisher Water-Base Sanding Sealer flows evenly to
fill wood pores for a smooth, sealed surface with minimal grain
raising. Pro Finisher Water-based Sanding Sealer can also be
used over a previously stained floor. Note: Pro Finisher WaterBase Sealer will darken white oak floors. Always test on a piece
of scrap wood or in an inconspicuous area before applying to the
entire floor.
.PRODUCTS
SKU
137153
Apply when air and surface temperature is between 60°F and
80°F (10°C and 27°C). Substrate moisture content should not
exceed 12%. Warmer temperatures will accelerate and colder
temperatures will prolong the dry time of this product. Do not
apply if humidity exceeds 85% or when temperature is within 10°
of the dew point.
Stir thoroughly before use and frequently during use. Do not
shake container or bubbles will form in sealer. Apply product
using synthetic pad or Universal Applicator. Apply in direction of
wood grain in smooth, level strokes at a rate of approximately
500-600 square feet per gallon. Do not over-work sealer. Coat
only a few board widths at a time, being sure to keep a wet edge.
Allow sealer to dry 1-2 hours before sanding or recoating. Note
that Pro Finisher Water-based Sealer may darken white oak
floors. Always test on a piece of scrap wood or in an
inconspicuous area before applying to the entire floor.
.
Description
1-Gallon
..SURFACE PREPARATION
.
.
Surfaces must be clean, dry and free from old finish, wax, grease
and dust. To remove grease, oils or adhesive use a rag
dampened with mineral spirits. Sand area smooth beginning with
#100 grit sandpaper and progressing through #150 and #220
grits. Remove all sanding dust and dirt with a vacuum or tack
cloth. For hardwood floors, use NOFMA or NWFA accepted
methods or see Pro Finisher Professional Finishing Techniques
for sanding details. Final wipe the surface with a clean, lint free
cloth to pick up any residual dust.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative
humidity. Lower temperatures, higher humidity and heavy or
multiple coats will prolong dry time. In most cases Pro Finisher
Water-based Sealer will dry to touch in 30-45 minutes and can
be sanded or recoated after 1 hour. Allow 24 hours for light traffic
and 7 days for full cure.
COVERAGE
Pro Finisher Water-based Sealer may raise the grain of the wood
to some extent. Smooth down raised grain using an oscillating
buffer with #120 or #150 grit screen. This will also abrade the
surface of the sealer to ensure adhesion of the finish coat. After
abrading sealer coat, thoroughly vacuum surface and then mop
with a water-dampened, lint-free cloth to pick up any residual
dust.
One gallon of Pro Finisher Sanding Sealer will cover
2
approximately 550 square feet (51 m ) on smooth, dense woods
2
such as maple and 450 square feet (46 m ) on porous woods
such as oak. Application may vary due to the porosity of the
substrate and the method of application.
CLEAN-UP:
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
Clean application tools and equipment with soap and water.
1
Form: GDH-813
Rev.: 051217
TECHNICAL DATA
PRO FINISHER WATER-BASED SANDING SEALER
PHYSICAL PROPERTIES
.
PRO FINISHER WATER-BASED SANDING SEALER
Resin Type
Acrylic
Pigments
NA
Solvents
Diethylene Glycol Monobutyl Ether, Water
Weight
Solids
Per Gallon
8.54 lbs
Per Liter
1.02 kg
By Weight
28.6%
By Volume
26.5%
Volatile Organic Compounds
162 g/l (1.35 lbs. /gal.)
Recommended Dry Film Thickness
(DFT) per Coat
0.5-1.0 mils
(12.5-25µ)
Wet Film to Achieve DFT (unthinned
material)
2.0-4.0 mils
(50-100µ)
Practical Coverage at Recommended
DFT (assumes 15% material loss)
Dry Times at 70-80°F
(21-27°C) and 50%
Relative Humidity
550 sq.ft./gal.
(13.5 m²/l)
Touch
30-45 minutes
Recoat
1 hour
Light Traffic
24 hours
Full Cure
7 days
Shelf Life
3 years
Flash Point
>220°F (104°C)
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature
do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we
can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All
technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-813
Rev.: 051217
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement