Vissani 668I/CS53 User guide

Vissani 668I/CS53 User guide
USE and CARE manual
Operation instruction:
Powering on/off and Settings:
Lamp Timer Minus Clock
Plus
Fan
Power/Standby
Lamp: Press the lamp display one time to activate the light, press the lamp display again to
deactivate it.
Power/Standby: When the range hood is in the “original” state, touch this button. It will
enter the standby mode.
Setting the clock: When the range hood is on “Standby” Mode, press and hold the timer
button for 3 seconds. The range hood will then enter the time setting state; the display
screen will show numbers. Press the Plus to set hours and Press the Minus to set the minutes.
After 10 seconds, it will automatically exit the time setting state and the time you have
entered will be saved.
Timer:
oWhen the fans are operating, touch the timer button one time. This will turn on the timer
mode and the display with show 03:00. Each time you press the timer button, it will increase
by 1 minute with the maximum timer setting of 60 minutes. Within the last 3 seconds of the
timer setting, the range hood will make three beeps.
oWhen range hood is on, touch the Power/Standby once and the shut off timer will set to 60
seconds. Touch the button twice and the fan will turn off.
Fan Operation:
oIn standby mode, press the Minus button one time and the range hood will start at F1
speed. If the button is pressed again, the speed will stay the same.
oIn standby mode, press the Plus button one time, the range hood will start at F3 speed. If
the button is pressed again, the speed will stay the same.
oTo lower or increase the fan speed press the Plus or Minus buttons.
oWhen fan is in the standby mode, press the Fan button to reach maximum speed
immediately. Touching this button while in a lower speed will automatically take to the
maximum speed. Touching the Fan button twice will turn the fan off.
Cleaning
IMPORTANT: Clean the hood and panel filters frequently per the following instructions.
Replace the panel filters before operating hood.
Exterior Surfaces
To avoid damage to the exterior surface, do not use steel wool or soap filled scouring pads.
Always wipe dry to avoid water marks.
Cleaning Method
Use liquid mild-detergent soap and water, do not use hard abrasive cleaners.
Wipe with damp soft cloth or non-abrasive sponge, then rinse with clean water and wipe dry.
Do’s:
Clean your range hood using a non-abrasive cloth or sponge and liquid detergent.
Always wipe in the direction of the grain pattern.
After cleaning rinse with water.
Make sure range hood is dry after cleaning.
Don’ts:
Do not use steel wool or like products as this will cause scratching and iron residue that
could lead to rusting and corrosion.
Do not wipe against the grain pattern as this will impact the original finish.
Do not use chlorine bleach.
Grease/Baffle Filter
Wash baffle filters as needed in dishwasher or hot detergent solution (low temperature,
short cycle).
Make sure filters are completely dry before putting back into range hood.
Reinstall the filter by making sure the spring release handles are toward the front.
filter into upper track.
Insert
Push the spring release handle.
Push up on filter and release handle to latch into place.
Note: For models that have a stainless panel as shown below, pull down the panel to access
the aluminum mesh filter and follow directions above.
Replacing the LED light (Replacement Bulb Part Number: WRHLB1S2)
Turn off the range hood and allow the LED light to cool.
To avoid damage or decreasing the life of the new bulb, do not touch bulb with bare
fingers. Replace bulb wearing cotton gloves to handle bulb.
If new LED light does not operate, make sure the lamps are inserted correctly before
calling for support.
To replace:
1.Disconnect the power cord to ensure unit does not turn on.
2.Remove filters.
3.Reach behind the light and push towards you until the light pops out. A screwdriver may be
needed to push out light in some models.
4.Disconnect the electrical harness.
5.Attach new bulbs to the electrical harness.
6.Snap bulbs back into unit and replace filters.
7.Reconnect the power cord.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement