Rust-Oleum | 338806 | User guide | Rust-Oleum 338806 User guide

TECHNICAL DATA
ROC-146
RUST-OLEUM®
GARAGE + INTERIOR FLOOR PRIMER
DESCRIPTION AND USES
PRODUCT APPLICATION (cont.)
Rust-Oleum® Garage & Interior Floor Primer is an easy to
use, revolutionary technology which allows you to coat over
a previously coated or sealed concrete floor without having
to scuff, sand, or grind the surface. Transform your worn
garage or basement floor with any Rust-Oleum floor coating
(including water and solvent base).
SURFACE PREPARATION (cont.)
PRODUCT FEATURES



Water-based acrylic
No sanding
No grinding
PRODUCT
SKU
338806
DESCRIPTION (1 Gallon)
Garage & Interior Floor Primer
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
For use on previously coated or sealed concrete floors in
garages, carports, basements, laundry rooms, and other
interior surfaces. May be applied to bare, etched concrete.
Note: This Garage & Interior Floor Primer is not a suitable
replacement for etching a concrete surface.
Bare Concrete Surfaces: For proper penetration and
maximum adhesion, use Rust-Oleum Concrete Etch or RustOleum Clean & Etch (sold separately). Follow label
instructions carefully and allow the floor to dry completely.
Wipe your fingers over the clean, dry surface. If you see any
dust or powder on your fingers, repeat scrubbing and rinsing
until the floor is clean.
Previously Painted, Stained or Sealed Concrete
Surfaces: Use a wire brush to remove any loose or peeling
paint, stain or sealer. To ensure proper adhesion, thoroughly
clean with a concrete cleaner & degreaser before applying
Garage & Interior Floor Primer.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT
WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a
NIOSH-Approved respirator to control lead exposure. Clean
up carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800424-LEAD or log on to www.epa.gov/lead.
APPLICATION
LIMITATIONS
Do not use over superhydrophobic sealers or floors
contaminated with tire seal and protectant products. Not
recommended for asphalt.
Note: Garage & Interior Floor Primer is a gray color. Clear
topcoats are not recommended for use over Garage &
Interior Floor Primer.
SURFACE PREPARATION
Whether over bare or previously coated concrete, proper
surface preparation is critical to performance. Allow new
concrete to cure for a minimum of 28 days. Before coating,
if necessary, use a wire brush or sander to remove any
loose or unsound concrete or masonry. Remove grease, oil,
salt and other contaminants with Rust-Oleum Heavy-Duty
Degreaser or Rust-Oleum Cleaner & Degreaser (sold
separately). Scrub spots thoroughly with a stiff bristle brush
or broom and wipe up excess cleaner with rags or paper
towels to keep contaminates from spreading. Rinse
thoroughly with fresh water. Repeat as necessary until
completely clean.
Rust-Oleum Garage & Interior Floor Primer is ready to use.
Do not thin. Apply only when air (ambient) temperature is
between 50-90ºF (10-32ºC) and the relative humidity is below
85%. Do not paint outdoors if rain is expected within 24
hours. Stir thoroughly before applying.
Use a brush or edger to trim the perimeter and hard-to-reach
areas. Use a long handled extension pole and a high quality
⅜” nap roller cover to apply an even coat of Rust-Oleum
Garage & Interior Floor Primer onto the surface. Apply in 4’x4’
foot sections and maintain a wet edge while rolling. Continue
applying in 4’x4’ sections until complete. Do not let product
puddle. Only one coat is recommended.
DRY & RECOAT TIMES
Dry and recoat times are based on 70ºF and 50% relative
humidity. Dry times increase at cooler temperatures. Garage
& Interior Floor Primer must be allowed to dry a minimum of 6
hours, but no more than 48 hours, to ensure proper adhesion
of topcoat.
CLEAN-UP
Wash tools and equipment with warm water and a mild
detergent immediately after use. Properly dispose of all
soiled rags and protect unused product from freezing.
1
Form: ARJ-1767
Rev.: 022619
TECHNICAL DATA
ROC-146
RUST-OLEUM®
GARAGE + INTERIOR FLOOR PRIMER
PHYSICAL PROPERTIES
GARAGE+ INTERIOR FLOOR PRIMER
Resin Type
Acrylic
Pigment Type
Titanium Dioxide, Carbon Black
Solvents
Weight
Solids
Water, Propylene Glycol
Per Gallon
11.2 lbs.
Per Liter
1.34 kg
By Weight
49.3%
By Volume
28.6%
Volatile Organic Compounds
<100 g/l
Recommended Dry Film Thickness (DFT)
Per Coat
1-2 mils
(25-50µ)
Wet Film to Achieve DFT
(unthinned material)
4-7 mils
(100-175µ)
Practical Coverage at
Recommended DFT (per coat)
Dry Times at 70-80°F
(21-27°C) and 50%
Relative Humidity
200-400 sq.ft./gal
Coverage rate can vary depending on the texture and porosity of the concrete
Top Coat
Full Traffic
Shelf Life
After a minimum of 6 hours and before 48 hours
72 hours
2 years
For additional information, see SDS
Safety Information
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
Phone: 888∙683∙5667
www.rustoleum.com
Form: ARJ-1767
Rev.: 022619

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project