BV BV-RH-801 30 in. 900 CFM Under Cabinet Range Hood with Baffle Filters, LED Lights and Push Buttons in Seamless Stainless Steel Installation Guide

BV BV-RH-801 30 in. 900 CFM Under Cabinet Range Hood with Baffle Filters, LED Lights and Push Buttons in Seamless Stainless Steel Installation Guide
Classic Series Under Cabinet
RANGE HOOD
MODEL: BV-RH-801
INSTALLatiON GUIDE and USER MANUAL
[ 6” High, 6” Top Vent, 1mm Thickness ]
CONTENTS
Important!! Test Before Installation ...........................................................................................................................
Know Before Installation ................................................................................................................................................
Included Parts and Accessories ...................................................................................................................................
Important Safety Notice .................................................................................................................................................
Venting Height Requirements .....................................................................................................................................
Venting Methods ..............................................................................................................................................................
Electrical Requirements and Specifications ............................................................................................................
Installation Preparation ..................................................................................................................................................
Installation Instructions ..................................................................................................................................................
Range Hood Operations ................................................................................................................................................
Troubleshooting ...............................................................................................................................................................
Maintenance and Cleaning ..........................................................................................................................................
Warranty ..............................................................................................................................................................................
2
3
4
5
7
9
10
11
12
13
14
15
16
IMPORTANT!! TEST BEFORE INSTALLatION
READ and SAVE THESE INSTRUCTIONS
Installer: Leave this guide with the homeowner
Homeowner: Keep this guide for future reference
1. Please unpack the range hood and accessories carefully.
2. Remove the baffle filters, check any dent or damage inside and outside.
3. If found any loosing parts, please remove them.
4. Place the range hood on a flat stable surface, plug in 120V AC power source. Press the power button and the
speed buttons to turn on.
5. Check if any unusual metal touching noise, check the speed variation, and press the Light button to check the lights.
6. Verify all functions per Section RANGE HOOD OPERATIONS.
7. Refer to Section TROUBLESHOOTING if any malfunction was found.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING
CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT.
Strongly recommend to test the unit before installation for any defective or damage during shipment.
Always disconnect, lock and tag power source before installing or servicing product. Failure to
disconnect power source can result in fire, shock or serious injury.
Installation work and electrical wiring must be done by qualified person(s) in accordance with
all applicable codes and standards, including fire-rated construction.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden
utilities.
Verify and ensure the rated voltage and frequency (please refer to the rating label) of the
range hood is in compliance with the mains supply.
PLEASE READ AND SAVE THESE INSTRUCTIONS
2
KNOW BEFORE INSTALLation
Research, plan and prepare the optional accessories and tools.
DUCT VENTING AND ACCESSORIES (NOT INCLUDED)
If for new installation or your old range hood doesn’t have exhaust duct,
prepare to cut the openings through the bottom of the cabinet, wall, or top
cabinet to ceiling. And purchase the 6” metal duct (or 6” semi-rigid aluminum
duct for easy connection). Refer to Section 5 VENTING METHODS for detail.
Check the existing exhaust duct size. If not 6” round metal duct, try to get the
converter / reducer / adapter / elbow as shown in the pictures.
Damper is NOT included. Because the damper generates NOISE when the shutters are flipping, we
DO NOT recommend installing the damper directly attached to the top vent of the range hood. You
can install the damper between ducts and close to the air outlet near roof or side wall. If the roof
cap or side wall cap already has a damper, don’t need to add the damper.
Also prepare the cutting tools (jig saw or reciprocating saw), screw drivers or power drill, level,
measuring tape, knife, duct/foil tape, screws, marker/pencil, etc.
2 people are required for the installation.
3
INCLUDED PARTS and accessories
RANGE HOOD
BAFFLE FILTERS
Note: the supplied are subjected to change without notice due to product development.
4
important safety notice
READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE
INSTALLATION CAUTIONS
The installation in this manual is intended for qualified installers, service technicians or persons with similar
qualified background. Installation and electrical wiring must be done by qualified professionals and in
accordance with all applicable codes and standards, including fire-rated construction.
DO NOT attempt to install this appliance yourself. Injury could result from installing the unit due to lack of
appropriate electrical and technical background.
Range hood may have very sharp edges; please wear protective gloves if it is necessary to remove any parts for
installing, cleaning or servicing.
Before installation, turn on the range hood to test for any damage / defect due to shipping.
Due to the size and weight of this range hood, two people installation is required.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials and vapors.
The combustion air flow needed for safe operation of fuel-burning equipment may be affected by this unit’s
operation. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local code authorities.
Before servicing or cleaning unit, unplug the power cord or switch power OFF at service panel and lock service panel to pre-vent power from being switched ON accidentally.
Clean grease laden surfaces frequently. To reduce the risk of fire and to disperse air properly, make sure to
vent air outdoors. DO NOT vent exhaust into spaces between walls, crawl spaces, ceiling, attics or garages.
Use only metal ductwork and this unit MUST be grounded.
Sufficient air is needed for proper combustion and exhausting of gases through the duct to prevent back
drafting.
When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
All electrical wiring must be properly installed, insulated and grounded.
Old duct work should be cleaned or replaced if necessary to avoid the possibility of a grease fire.
Check all joints on duct work to insure proper connection and all joints should be properly taped.
Use this unit only in the manner intended by the manufacturer. If you have questions, contact the vendor
5
important safety notice
TO REDUCE THE RISK OF A STOVE TOP GREASE FIRE:
Keep all fan, baffle, spaces, filter, and grease-laden surfaces clean. Grease should not be allowed to accumulate on fan, baffle, spaces, and filter.
Always turn range hood ON when cooking at high heat or when cooking flaming foods.
Use high settings on cooking range only when necessary.
Never leave surface units (countertop/stove) unattended at high settings. Boil overs cause smoking and
greasy spillover that may ignite. Heat oils slowly on low or medium settings.
Clean ventilating fan frequently.
Always use cookware appropriate for the size of the surface element.
TO REDUCE THE RISK OF INJURY IN THE EVENT OF A STOVE TOP GREASE FIRE:
SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn OFF the burner. BECAREFUL
TO PREVENT BURNS. NEVER PICK UP A FLAMING PAN—you may be burned. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames DO NOT go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT or 911.
DO NOT USE WATER, including wet dishcloths or towels — a violent steam explosion will result.
Use an extinguisher ONLY if:
You know you have a Class A, B, C extinguisher, and you already know how to operate it.
The fire is small and contained in the area where it is started.
The fire department is being called.
You can fight the fire with your back to an exit.
TO REDUCE THE INJURY IN THE EVENT OF A GAS LEAKS:
Extinguish any open flame.
DO NOT turn on the lights or any type of appliance.
Open all doors and windows to disperse the gas. If you still smell gas, call the gas company and fire department, or 911 immediately.
Your safety and the safety of others are very important. We have provided many important safety messages in this
manual and on your appliance. Always read and obey all safety messages. All safety messages will tell you what the
potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not
followed.
WARNING
This is the safety alert symbol. This symbol alerts you to potential hazards that can hurt you
and others. All safety messages will follow the safety alert symbol and the word “WARNING”.
6
Venting height requirements
VENTING HEIGHT REQUIREMENTS
Vent system must terminate to the outside (roof or side wall).
DO NOT terminate the vent system in an attic or other enclosed area.
DO NOT use 4” (10.2 cm) laundry-type wall caps.
Use metal/aluminum vent only. Rigid or flexible metal / aluminum
vent duct is recommended.
Cabinets
DO NOT use plastic vent.
Always keep the duct clean to ensure proper airflow.
Measure and estimate the following figures before installation:
1. Distance between the countertop/stove to the bottom of the range
hood. Recommend 27” to 30” for ideal performance, minimum 24”
(inches) for safety concern.
2. Height of hood and duct.
Range hood
For the most efficient & quiet operation:
A distance of 27” to 30” is recommended between stove top and the
bottom of range hood.
Min 24” Max 32”
Recommended 27” to 30”
The vent duct isn’t included. It is recommended that the range hood
be vented vertically through the roof through 6” (15.24 cm) or bigger round metal/aluminum vent work, such as 6 in. x 8 ft. semi-rigid
aluminum flexible duct.
The size of the vent should be uniform.
Use no more than three 90° elbows.
Stove top
Make sure there is a minimum of 24” (61 cm) of straight vent between
the elbows if more than one elbow is used.
DO NOT install two elbows together.
The length of vent system and number of elbows should be kept to a
minimum to pro-vide efficient performance.
The vent system should have a damper. The damper can be installed
in the duct near to the roof or wall cap. Not recommend to use damper on top of the range hood, because the damper has big noise.
Use silver tape or duct tape to seal all joints in the vent system.
Use caulking silicone to seal exterior wall or roof opening around the
cap.
7
Venting height requirements
IMPORTANT:
Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps.
ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required, increase duct size
from 6” to 7”, 8” or 9”. If a reducer is used, install a long reducer instead of a pancake reducer. Reducing duct size will
restrict airflow and decrease airflow, thus reduce duct size as far away from opening as possible.
If turns or transitions are required: Install as far away from opening and as far apart, between 2, as possible.
Minimum mount height between stove top to hood bottom should be no less than 24-inch.
Maximum mount height between stove top to hood bottom should be no higher than 32-inch.
It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard; while hoods mounted too high will be hard to reach and will reduce its performance and efficiency.
If available, also refer to stove top manufacturer’s height clearance requirements and recommended hood mounting
height above range.
Minimum Duct Size:
Round - 6” minimum
Rectangular - 3-1/4 x 10” minimum (requires a 6” to 3-1/4x10” adaptor, not supplied)
CALCUlating vent system length
To calculate the length of the system you need, deduct the equivalent feet for each vent piece used in the system from
the recommended maximum duct run.
DUCT RUN CALCULATION
Recommended maximum straight duct run
6” or 3-1/4 x 10” duct
50 ft
Duct Run Calculation example:
One roof cap, two 90º elbow, and one 45º elbow used:
Vent piece deduction
Each 90° elbow used
9 ft
Each 45° elbow used
5 ft
Each 6” to 3/12 x 10” transition used
7 ft
Side wall cap with damper
0 ft
Each 90° elbow used
0 ft
0ft + 9ft + 9ft + 5ft = 23ft used.
Deduct 23ft from 50ft, 27ft maximum available for the
duct run.
8
Venting methods
VENTING METHODS
This range hood is 6” top venting through the roof or wall.
Vent work can terminate either through the roof or wall as shown below.
A minimum of 6” round duct (purchase separately) or 3-1/4 x 10” rectangular duct (purchase separately) must be
used to maintain maximum airflow efficiency.
Always use rigid or semi-rigid type metal/aluminum ducts if available to maximize airflow.
Decide the location of the venting pipe from the hood to the outside.
A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows,
and long run as possible. This may reduce the performance of the hood.
IMPORTANT:
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All
exhaust must be ducted to the outside.
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
Use caulking to seal exterior wall or roof opening around the cap.
Roof Cap
Cabinet
Side Wall Cap
Range Hood
Stove Top
TOP Venting roof exhaust
TOP Venting wall exhaust
9
electrical requirements and specifications
IMPORTANT: Observe all governing codes and ordinances.
It is the customer’s responsibility to contact a qualified electrical installer.
A 120 Volt, 60 Hz, AC only, fused electrical supply is required on a 15-amp circuit.
DO NOT have a fuse in the neutral or ground circuit.
The 3-prong outlet should be grounded. If the power cord plug is not used, the power cord’s green wire should be
connected to ground. Check with a qualified electrician if you are not sure that the range hood is properly grounded.
DO NOT ground to a gas pipe.
The range hood must be connected with copper wire/plug only.
The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible
armored or non-metallic sheathed copper cable. ETL listed strain relief must be provided at each end of the power
supply cable.
WARNING
Hazard of electrical shock!
Do not perform service on an electrically live
system. Disconnect the main electrical
supply before servicing this device. Touching
electrical connectors or other exposed electrical
circuitry inside this range hood when they
are energized could result in death, serious
bodily injury, or property damage.
Specifications:
Body Design
Seamless Stainless Steel, Satin Finish
Power Rating
120V / 60Hz (USA & Canada standard)
General Input Power
156W (150W + 2x3W)
Motor Input Power
Max: 150W (75W + 75W), Min: 110W (55W + 55W)
Ampere
2A
Levels Of Speed Control
4 Levels
Airflow (Q/L/M/H)
385CFM / 490CFM / 615CFM / 900CFM
Noise Level (Q/L/M/H)
1.5Sone(46dB) / 3.5Sone(58dB) / 5.3Sone(64dB) / 7.5Sone(69dB)
Number Of Motors
2 Motors
Motor Type
Single Chamber Ultra Quiet
Fan Type
Centrifugal Blower
Control Type
Soft Touch Electronic Control Panel with LED Light
Filtration Type
Stainless Steel Baffle Filter
Illumination
3W 12V Maximum
Venting Size
Top, 6 inches Round
Interference Protection
Radio Frequency Interference Protected
10
INstallation preparation
Please unpack the range hood and accessories carefully.
Remove the baffle filters.
Check for any dent or damage inside and outside. If found any loosing parts, please remove them.
Place the range hood on a flat stable surface. Connect the range hood to a designated standard outlet (120-Volt,
60Hz, AC only). Press the power button and the speed buttons to turn on.
Check if any unusual metal touching noise, check the speed variation, and press the Light button to check the lights.
Verify all functions by referring to Section RANGE HOOD OPERATIONS. Refer to Section TROUBLESHOOTING if any
malfunction was found.
Place all supplied parts and required hardware on a flat stable surface and verify the existence of all supplied parts
listed on Section INCLUDED PARTS AND ACCESSORIES.
Carefully remove the white plastic protective film from the range hood if any. The white protective film might not
cover all stainless steel area; it was removed prior for welding or packing.
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
CAUTION: If moving the cooking range is necessary to install the hood, unplug the power on an
electric range. SHUT OFF THE GAS VALVE BEFORE MOVING A GAS RANGE.
11
INstallation INSTRUCTIONS
1) Installation planning
Measure the distance between stove top and the bottom of range hood. A distance of 27” to 30” is recommended.
Minimum 24” is required for safety concern.
Decide the venting method and the location of the venting pipe from the hood to the outside.
Purchase any necessary accessories from a hardware store, such as duct, elbow, reducer, damper, duct tape, screws, etc.
Find and mark the stud locations using a stud finder to plan the mounting locations firmly.
2) Measure the top vent and the power cord positions, cut the openings (slightly larger for easy accessible) for hood
exhaust and power cord under the cabinet.
3) For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not
provided) on each side.
4) Puncture the power cord’s knockout hole and through the power cord from inside of the range hood
to outside.
5) Puncture the knockout screw holes on the top for screw mounting under the cabinet.
4”WIDE
4”WIDE
WALL
6) Mount this range hood under the cabinet, 2 people are required for this installation.
Draw power cord through cabinet access opening and center the hood beneath the cabinet.
From inside of the hood, place screws into the exact center of each knockout hole and secure
to cabinet bottom. Finish tightening all screws until secure.
CAUTION: Make sure the range hood is secure before releasing!
For safety purpose, mount the screws through the pre-drilled mounting holes or/and drill new holes from inside
the back of the hood to the studs or lumbers. For a more secure installation, use as many mounting holes as needed
to secure from the inside of hood.
7) Use 6” round metal duct (or semi-rigid aluminum duct, follow building codes in your area) to
connect the exhaust on the hood to the duct-work above. Use foil tape or duct tape to make
all joints secure and air tight.
8) Connect the range hood to a designated grounded standard outlet.
Or cut off the plug and connect three wires (black, white and green) to house wires and cap
with wire connectors. Connect according to colors (i.e. black to black, white to white, and
green to green). Store excess wires in the wiring box.
9) Install baffle filters and stainless spacer if any.
Baffle Filters and Stainless Steel Spacers
30” Range Hood
36” Range Hood
10) Turn power ON in control panel. Check all lights and fan operations.
12
range hood operations
Control Panel Layout and Buttons Configurations:
Light Control:
Press Light Control button once to turn on the lights, and once again to turn off the lights.
The Light Control button operates independently from the Power Control (On/Off) button. Pressing the
Power Control button will not turn LED lights ON or OFF.
Please turn off the LED lights before activating the power-off delay function. While Light Control button
will NOT be affected by the power-off delay function.
Turning Fan ON:
Always turn fans ON couple minutes before cooking to establish air flow and allow fans to run for a few
minutes after cooking for cleaner air in the kitchen.
The Power Control (On/Off) button must be pressed before a Speed Control button can be activated.
Blower Speed Selection:
With the range hood is OFF, press the Power Control (On/Off) button once. The LED on the Power Control
button will be illuminated.
While the Power Control LED is illuminated, press one of the four speed control button (Quiet, Low, Medium,
and High) to activate the desired speed (the LED on the speed control button will turn on).
To change the fan speed, press another speed control button. The LED on the speed control button will
become illuminated accordingly.
Power-Off Delay Function:
When the fans are operating in any speed, press the Power Control (On/Off) once to turn on the 3-minute
power-off delay function.
While the fans are in 3-minute power-off delay mode, press the Power Control (On/Off) button once to turn
OFF the fans immediately.
Power Control (On/Off):
When the fans are operating in any speed, press the Power Control (On/Off) button twice to turn OFF the
fans immediately.
Operation Cautions:
Read and undzerstand all instructions and warnings in this manual before operating the appliance.
Always leave safety grills and filters in place. Without these components, operating blowers could catch on
to hair, fingers and loose clothing.
NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers.
NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk
of self-combustion is higher when the oil has been used several times.
NEVER cook on “open” flames under the range hood. Check deep-fryers during use: Superheated oil may
be flammable.
13
troubleshooting
WARNING
Hazard of electrical shock!
Do not perform service on an electrically live
system. Disconnect the main electrical
supply before servicing this device. Touching
electrical connectors or other exposed electrical
circuitry inside this range hood when they
are energized could result in death, serious
bodily injury, or property damage.
If the range hood or LED light does
not operate after installation
The range hood vibrates when the
blower is on
Check if the range hood has been plugged in, make sure that all power
has been turned back ON, fused not blown and all electrical wiring are
properly connected.
Swap out light assembly to working ones to deter-mine whether it is
caused by defective bulbs. See Replacing the Light Bulbs on Page 14.
The range hood might not have been secured properly on to the cabinet
or wall.
Check that the duct sized used is at least 6” or 3-1/4 x 10”. Range hood
WILL NOT function efficiently with insufficient duct size. For example: 7”
duct over 6” top vent and loosely secured.
The blower or fan seems weak
Check if duct is clogged or if damper unit (half-circular flapper) is not
installed correctly or opening properly. A tight mesh on a side wall cap
unit might also cause restriction to the air flow.
The blower might be jammed or scraping the bottom due to shipping
damage.
The lights work but the blower is
not spinning at all, is stuck or is rattling.
The hood is not venting out properly.
Disconnect the power cord, remove the fan grill and the fan blade, might
see the fan blade or/and motor is not in the proper position (offset from
the center). Try to fix/adjust it or please contact us immediately.
Make sure the distance between the stove top and the bottom of the
hood is within recommended 27” and 30” in distance. *Due to different
ceiling height configurations, recommended height may not
be applicable.
Reduce the number of elbows and length of duct work. Check if all joints
are properly connected, sealed, and taped.
Make sure the power is on high speed for heavy cooking.
14
maintenance and cleaning
Cleaning:
The saturation of greasy residue in the blower and filters may cause increased inflammability. Keep unit clean and free
of grease and residue build-up at all times to prevent possible fires.
For optimal operation, clean range hood and all baffle/spacer/filter regularly. Regular care will help preserve the
appearance of the range hood.
Filters must be cleaned periodically and free from accumulation of cooking residue. Old and worn filters must be
replaced immediately.
DO NOT operate blowers when filters are removed. Never disassemble parts to clean without proper instructions.
Disassembly is recommended to be performed by qualified personnel only. Read and understand all instructions
and warnings in this manual before proceeding.
SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!
Cleaning Exterior Stainless Steel Surfaces:
Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent, or
steel wool/scoring pads, which will scratch and damage the stainless steel surface. For heavier soil use liquid
degrease cleaner.
If hood looks splotchy, use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning
solution onto or into the control panel. Follow directions of the stainless steel cleaner.
CAUTION: DO NOT leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the
cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood.
After cleaning, you may use nonabrasive stainless steel polish, to polish and buff out the stainless luster and grain.
Always scrub lightly, with clean cotton cloth, and with the grain.
DO NOT allow deposits to accumulate or remain on the hood.
DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel
for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after
exposure and wipe dry with a clean cloth.
Cleaning Stainless Steel Baffle Filters:
Remove all baffles, spacers, filters, discard oil and residue.
IMPORTANT: Drain oil from baffles, spacers, and filters before oil and residue overflow!
Wash with warm soapy water. NOTE: Stainless steel baffles and spacers are top rack dishwasher safe.
Dry thoroughly before replacing and follow directions for installation in reverse.
Filters should be cleaned after every 30 hours of use.
Replacing Filters:
Should filters wear out due to age and prolonged use, replace the baffle filters
immediately.
Replacing the Light Bulbs:
This range hood uses LED bulbs: 3W 12V.
Make sure the range hood is unplugged or turn OFF breaker.
1. Gently pull the defective bulb assembly straight out from the edge, and then disconnect
the wires.
2. Connect the new LED bulb’s wires and snap the new LED assembly into the housing hole.
3. Turn ON breaker/power and to test the range hood for operation.
15
Warranty
Please provide an original dated proof of purchase (sales receipt / invoice) in order to obtain warranty.
One Year Parts Warranty:
For one year from the date of original purchase, we will provide free of charge, non-consumable replacement parts
or components that failed due to manufacturing defects. Subject to the conditions and limitations set forth below,
we will, at its option, either repair or replace any part of its products that prove defective by reason of improper
workmanship or materials.
Repaired parts or replacement products will be provided by us on an exchange basis, and will be either new or
refurbished to be functionally equivalent to new.
The consumer is responsible for all shipping costs.
Consumable parts not covered by this warranty include but not limited to: light bulbs, stainless steel baffle filters.
Who is Covered?
This warranty is extended to the original purchaser for products purchased for ordinary home use in the
continental USA.
This Warranty Will Be Voided When:
Product damaged through negligence, improper installation, accident, abuse, misuse, natural disaster, insufficient
or excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized repair,
disassembly, modification, or failure to follow installation instructions.
When product is used commercially or other than its intended purpose.
Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by
anyone other than our authorized agents.
This limited warranty also does not apply to any product on which the original identification information has
been altered, obliterated or removed, has not been handled or packaged correctly, has been sold as second-hand.
What is Not Covered?
Consumable parts such as light bulbs, stainless steel baffle filters. The natural wear of finish, and wear due to
improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products.
Chips, dents or cracks due to abuse, misuse, freight damage, or improper installation.
Damage of product caused by accident, fire, floods or act of God. It is not liable for, and does not cover under
warranty, any loss of properties or any costs associated with removing, servicing, installing, or determining the
source of problems with our products.
This warranty is valid in the United States. It is non-transferable and applies only to the original purchaser and does not
extend to subsequent owners of this product. Any applicable implied warranties, including the warranty of merchantability, are limited in duration to a period of express warranty as provided herein beginning with the date of original
purchase at retail and, no warranties, whether express or implied, shall apply to this product thereafter.
To obtain warranty service, you may contact us, its dealer or distributor from which you purchased the product. Please
confirm the terms of your dealer’s or distributor’s policies prior to contacting. Typically, you must include product
identification information, including model number and lot number with a detailed description of the problem you are
experiencing. You must also include proof of the date of original retail purchase as evidence that the product is within
the applicable warranty period.
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement