Zinsser 00301, 00704H, 408, 300, 00304H User manual

Zinsser 00301, 00704H, 408, 300, 00304H User manual
TECHNICAL DATA
BEY-06
BULLS-EYE® SHELLAC
.DESCRIPTION AND USES
PRODUCT APPLICATION (cont.)
.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
®
Bulls-Eye Shellac is a shellac-based sealer that is
designed to give wood a natural looking, mid-gloss finish
that will not yellow or darken with age.
Bulls-Eye Shellac is recommended for application to
interior walls, doors, trim, cabinets, furniture and related
paintable surfaces. It is suitable for use on new and
previously painted drywall, cured plaster, wood (pine, fir,
cedar, redwood, plywood), metal, and cured masonry
(stucco, concrete block, poured concrete, brick).
Bulls-Eye Shellac is suitable for use as a protective sealer
for tools, golf clubs, wood toys, and other items. It will
adhere to glass and ceramic tile.
PERFORMANCE CHARACTERISTICS






APPLICATION
Apply only when air, material, and surface temperatures
are between 50-90ºF (10-32ºC) and the relative humidity
is less than 85%. Thoroughly stir well before using. Do not
thin this product. Apply several light coats with a brush,
pad or lint-free wiping cloth and let dry for 1 hour before
sanding with 220 grit or finer sandpaper. Allow any
subsequent coats to dry at least 1hour before sanding
lightly and recoating. Bulls-Eye Shellac is not
recommended for use as a sealer under polyurethane.
When sealing wood under polyurethane finishes, use
Bulls-Eye SealCoat.
.
Mid-tone sheen
Will not darken with age
Blocks all odors in wood, plaster, drywall and
masonry
Easy clean up with ammonia and water
Dries in minutes, can be recoated in 1 hour
Dried film is non-toxic and hypo-allergenic
.PRODUCTS
SKU
408
316
716
308
708
304H
704H
301
701
201
601
300
700
200
600
.
WOODWORK
Description
12-Ounce Clear Spray
Half Pint Clear
Half Pint Amber
Pint Clear
Pint Amber
Quart Clear
Quart Amber
1-Gallon Clear
1-Gallon Amber
1-Gallon 4 lb. cut Clear
1-Gallon 4 lb. cut Amber
5-Gallon Clear
5-Gallon Amber
5-Gallon 4 lb. cut Clear
5-Gallon 4 lb. cut Amber
PRODUCT APPLICATION
.
Apply 1 or more light coats. Let dry completely before
sanding with 220 or finer grit sandpaper between coats to
ensure a smooth finish.
ODOR BARRIER/KNOT SEALER
Two full coats of Bulls-Eye Shellac will seal odors on bare
or previously coated drywall, plaster, masonry, and
woodwork and furniture. Apply one or two coats to knots
and sap streaks to prevent bleeding into the paint finish. If
the surface is to be painted, use B-I-N Primer-Sealer.
TINTING
Bulls-Eye Shellac can be tinted with up to 1.5 oz. (44 ml)
of universal colorant per quart. Shake container well
before using.
.
DRY & RECOAT TIMES
SURFACE PREPARATION
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
the touch in 30 minutes and can be recoated in less than 1
hour.
Surfaces should be clean, dry, sound and free of dust, dirt,
excessive chalky material, grime, grease, oil, wax, mildew,
wallpaper adhesive, or any contamination that may
interfere with adhesion. If unsure of cleanliness, always
wash surface with household ammonia and water solution,
appropriate cleaning solution or solvent (Do not use TSP
as a cleaner). Remove any peeling and/or unsound
coatings. Sand any remaining paint film edges smooth
with the surface. Bare wood that has been exposed for
more than 4 weeks should be lightly sanded with 80 to 100
grit sandpaper to remove weathered wood fibers.
CLEAN-UP
Clean wet tools, drips and spills with denatured alcohol or
household ammonia and water. Dispose of unused or
unwanted product in accordance with local laws regulating
solvent-based coatings.
1
Form: GDH-214
Rev.: 012814
TECHNICAL DATA
BULLS-EYE® SHELLAC
.PHYSICAL PROPERTIES
.
Physical Properties
BULLS-EYE SHELLAC
Resin Type
Shellac
MIR
1.00 Max
NA
Fill Weight
12 ounces
NA
Acetone, Denatured Alcohol, Ethanol
Denatured Alcohol, Ethanol, Water
Per Gallon
NA
7.3 lbs.
Per Liter
NA
0.86 kg
By Weight
NA
25.6%
By Volume
NA
19.3%
Volatile Organic Compounds
NA
<625 g/l
(5.2 lbs./gal.)
Theoretical Coverage at
1 mil DFT (25µ)
NA
310 sq.ft./gal.
2
(7.6 m /l)
8-10 sq.ft./can
2
(0.7-0.9 m /can)
100-150 sq.ft./quart (2.5-3.7 m /l)
depending on application method and
surface porosity
Touch
30 minutes
30 minutes
Recoat
1 hour
1 hour
24 hours
24 hours
3 years
3 years
-156°F (-104°C)
60ºF (16ºC)
Solvents
Weight
Solids
Practical Coverage at
Recommended DFT (assume
15% material loss)
Dry Times at 70°F
(21ºC) and 50%
Relative Humidity
Full Cure
Shelf Life
Flash Point
Safety Information
2
For additional information, see MSDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-214
Rev.: 012814
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement