Unbranded 3739M is a transfer shower floor designed for alcove framing installations. It is made of molded fiberglass and features a textured surface for slip resistance. The floor has a built-in drain and comes with a removable strainer for easy cleaning. The 3739M is designed to be installed on a bed of roofing felt or equivalent to compensate for any inconsistencies in the sub-floor or slab. It can also be installed on a wood/joist floor or a concrete/cement slab floor. The floor is ADA-compliant and can be equipped with support handrails that comply with ANSI-117.
PDF
Download
Document
Advertisement
Advertisement
MODEL 3739M TRANSFER SHOWER FLOOR INSTALLATION INSTRUCTIONS ADA — DESIGNED & ROUGH-IN DIMENSIONS PRODUCT til TYPICAL ALCOVE FRAMING ae ce STARBURST FF Г " 6 X [ | y | , Г == gore — me BE Tl | | | NM | 7 / | | ав] | > \| VA ze | 63 18 | 5 | || E 37 = Li Ill 37" + 1 67 | не == 39- — NOTE: Add horizontal blocking (not shown) as required for mounting grab bors, seof, etc IMPORTANT NOTES: * We suggest that shower compartments be equipped with support handrails that comply with ANSI-117.1-1986 Consumer Safety requirements « DO NOT USE WITH “FREE STANDING SHOWER CABINETS, FOR “BUILT-IN” INSTALLATION ONLY « SHOWER FLOORS ARE NOT TO BE INSTALLED IN FRONT OF DRYWALL! * Thoroughly READ and UNDERSTAND instructions before beginning installation of your MUSTEE Shower Floor ROUGH-IN PREPARATION IMPORTANT: "ROUGH-IN" dimensions are provided for reference only! Measure actual Shower Floor and check local buiding code requirements before constructing alcove. 1. Hefer to "ROUGH-IN" dimensions and determine location of Shower Floor. 2. Next, prepare SUB-FLOOR in Shower Floor area as follows: Wood/Joist Floor Sub-ficor must be min. 3/4" construction grade sheathing (CDX). Make sure sub-floor is securely fastened to floor joists throughout alcove area with either Decking/Bugle Head screws (2-1/2" min.) or nails (rec. 8d Spiral Flooring Nails). Make sure any “creaking or squeaks” have been eliminated by walking around alcove area before proceeding. Concrete/Cement Slab Floor: Prepare surface in alcove area so that floor is level and sound. 3. Provide a 6-1/2" (inch) square opening in sub-floor or slab to accommodate Shower Floor drain body. (Slab installation requires opening to be min. 2-1/2" deep). Opening to be centered about drain centerlines as specified In "ROUGH-IN" dimensions. Drain connection requires 2” (inch) DWV pipe. Top of drain pipe should be 1/2" below top of sub-floor or slab. 4. Finally, we recommend that Shower Floor be installed on a bed of 30 |b. roofing felt or equivalent to compensate for any inconsistencies in sub-floor or slab. (Gypsum cement or panel/floor adhesive could also be used for this purpose.) 51-198 (09*06) SHOWER FLOOR INSTALLATION 5. Check Shower Floor carefully making sure it is not damaged. 6. Set Shower Floor into place. Level Shower Floor in both directions. NOTE: Place level along top edge of tile flanges — do not use floor area which is tapered for water drainage! 7. Apply a lubricant of some type (liquid soap or silicone sealant works well) to the inside and outside of the Drain Seal’ prior to installation. Place Drain Seal over pipe and tamp into place using a hammer and -1/4" (inch) diameter blunt rod or dowel. (HINT: A 1/4” dia. bolt approx. 6” long works well as a tamping tool.) Make sure top of Drain Seal is even with top of 2" (inch) waste pipe and in full compliance with local code requirements pertaining to below floor waste connections. (See DRAIN DETAIL) 8. Snap Strainer into place. CARE 6: CLEANING The surface of your Molded Fiberglass Shower floor may be cleaned with a mild soap solution in warm water using a soft cloth. For stubbom stains use "Soft Scrub™ by Clorox or Lysol “Tub and Tile Cleaner” or a powdered detergent such as Spic-n-Span. Never Use an abrasive scouring powder or steel wool pads as they will dull the surface. SECTIONAL VIEW FINISHED WALL~ A, DRYWALL Al (rec WR SHEETROCK GYPSUM) FILL ALL AROUND WITH |, AA" CONTINUOUS BEAD E E 718 GAP ——RECESS SLICONE SEALANT — NB f Г 7 _ | 1 HIT —L но —— — REMOVABLE : FT ca a oca A | A STRAINER à 8" GAP—— \-SILICONE SEAL ANT BEDOING" A, HELPS PREVEN (see STEP 4) LEAKS-STOP SQUEAKS + ps a UB FLOOR SEAL DRAIN IN FULL COMPLIANCE WITH LOCAL | ad CODE REQUIREMENTS uE 2 PIPE-TOP OF ÊlPE 6 172" BELOW TOP OF SQUARE OPENNG SUB FLOOR DRAIN DETAIL t Optional DRAIN SEALS are available: | MT —SIRAINERT PN.-32.403 - 2 SOL PIPE/CAS T IRON-SERVICE WT. (NO HUB) еще = SANITARY DRAINAWASTE CONNECTIONS | ||| J SHOWER FLOOR PN.-32.404 - 2" COPPER-DWV, TYPE K, L or M ‘BEDDING’ + Optional STRAINERS are available: — PN.-34.305 - POLISHED BRASS #® (SEE NOTE) | PMN.-34.301 - POLISHED STAINLESS STEEL | | PN.-42.323 - MOLDED ("BONE") | < SUB-FLOOR $ ——— DRAIN SEALPN-32.401+ TO BE SURE THAT DRAIN SEAL | | — 2" IRON, PVC OR ABS SANITARY IS FULLY SEATED INTO DRAIN Secs 5 ala Ba USE ONLY "DWV BODY - DIMENSION SHOULD BE 1/2" (MIN.) | SEE STEP 7 ABOVE. | ACCESSORIES (ORDER SEPARATELY Pull-Down Shower Seats — Strong, durable, white Stainless Steel Grab Bars— Straight and inside pull-down seats made with 18-gauge stainless steel corner (L-shape) grab bars are concealed-flange tubing (satin finish) and comfortably padded with type and made with tough 18-gauge 1-1/2" diameter non-corded edges. Choice of sizes for right and stainless steel tubing, satin finish. left side installations. Part No. Size Type Part No. Size Type aes ga 5) 390.301 24" Straight 390.401 26" Right ee = = a = 390302 48” Straight 390.402 26" Left e Нее © 390303 20"x42" — L-shape 390.403 32” Right \ T 390.304 34"x18” — L-shape 390.404 32" Left — \ Quality Plumbing Products E.L. MUSTEE & SONS, INC. ea 5431 West 164th Street - Brook Park, Ohio 44142 51-195 (0906) ">

Public link updated
The public link to your chat has been updated.
Advertisement