Caution: You must read this before you proceed
CHAIR
Label
A
B
E
F
C
D
Picture Description
Chair Back
Chair Seat
Side Plate
Foot
Seat Cushion
Back Cushion
QTY
1
1
2
4
1
1
1 OF 6
Label
①
②
③
④
⑤
⑥
Picture
Before Beginning Assembly:
Description
Allen Key (M6)
Bolt (M6*40mm)
Washer
Allen Key (M4)
Bolt (M6*45mm)
Washer Ring
QTY
1
13
13
1
9
9
2 OF 6
Chair Back(A)
Back Cushion(F)
Seat Cushion(E)
Chair Seat(B)
Foot(D)
Side Plate(C)
FRONT FACING
This Chair has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Chair parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions here below to familiarise the parts and steps before assembly.
Step 1
Open the carton and place all the parts onto a clean, non-marring surface.
Attach Chair Back(A) to Chair Seat(B) using Bolt( ② ) and Washer( ③ ) with Allen Key( ① ) as shown above.
Only loosely tighten Bolts.
ATTENTION: There may be some PE wicker that may have covered the Mounting Points. To ease assembly, guide and slide the PE wicker away from these Mounting Points.
DO NOT CUT AWAY ANY PE WICKER as this would cause the wicker to unravel!
3 OF 6
Step 2
Attach Side Plate(C) between the Chair Back(A) and Chair Seat(B) using Bolt( ② ) and
Washer( ③ ) with Allen Key( ① ) as shown above.
Only loosely tighten Bolts.
Step 3
Place the Chair as shown in the picture above.
Attach Side Plate(C) between the Chair Back(A) and Chair Seat(B) using Bolt( ② ) and
Washer( ③ ) with Allen Key( ① ) as shown above.
Only loosely tighten Bolts.
Step 4
Attach the Feet(D) to the Chair using Bolt( ⑤ ) and Washer( ⑥ ) with Allen Key( ④ ) as shown above.
Only loosely tighten Bolts.
4 OF 6
Step 5
Turn the Chair right side up.
Place the Chair on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit into to the Chair.
This would help to align all the parts at all the joint areas.
Then get off the Chair, and in a sequential manner, proceed to tighten all bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there is still wobbles, loosen the bolts and execute this same process.
If the Chair is not stable it could lead to damage to the product.
Note: This step is done better with the assistance of a second adult.
Step 6
Place the Back Cushion(F) and Seat Cushion(E) onto the Chair.
Your Chair is ready for use.
Caution:This Chair can only be used on a flat, level surface.
5 OF 6
6 OF 6
Caution: You must read this before you proceed
CORNER
Label
A
B
C
D
E
F
G
H
Picture Description
Armrest
Corner Back
Corner Seat
Side Plate
Foot
Seat Cushion
Back Cushion
Back Cushion
1
1
1
4
1
1
QTY
1
1
Label
①
⑤
⑥
②
③
④
Before Beginning Assembly:
Picture Description
Allen Key (M6)
Bolt (M6*40mm)
Washer
Allen Key (M4)
Bolt (M6*45mm)
Washer Ring
QTY
1
9
9
13
13
1
Back Cushion (H) Armrest (A)
Back Cushion (G)
Corner Back (B)
Seat Cushion (F)
Foot(E)
Side Plate (D)
Corner Seat (C)
FRONT FACING
This Corner has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Corner parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1
Open the carton and place all the parts onto a clean, non-marring surface.
Place the Amrest(A) with its inside facing up .
Attach Coner Back(B) to Amrest (A) using Bolt( ② ) and Washer( ③ ) with Allen Key( ① ) as shown above.
Only loosely tighten Bolts.
ATTENTION: There may be some PE wicker that may have covered the Mounting Points. To ease assembly, guide and slide the PE wicker away from these Mounting Points.
DO NOT CUT AWAY ANY PE WICKER as this would cause the wicker to unravel!
Step 2
Attach Corner Seat(C) between the Armrest(A) and Chair Back(B) using Bolt( ② ) and Washer( ③ ) with Allen Key( ① ) from position # I to # V as shown above.
Only loosely tighten Bolts.
Step 3
Attach Side Plate(D) between the Corner Back(B) and Corner Seat(C) using Bolt( ② ) and Washer( ③ ) with Allen Key( ① ) as shown above.
Only loosely tighten Bolts.
Step 4
Attach the Feet(D) to the Chair using Bolts( ⑤ ) and Washer Rings( ⑥ ) with Allen Key( ④ ).
Step 5
Turn the Corner right side up.
Place the Corner on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit into to the Corner.
This would help to align all the parts at all the joint areas.
Then get off the Corner, and in a sequential manner, proceed to tighten all bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there is still wobbles, loosen the bolts and execute this same process.
If the Corner is not stable it could lead to damage to the product.
Step 6
Place the Back Cushion(G & H) and Seat Cushion(F) onto the Chair as shown.
Your Corner is ready for use.
Caution: This Corner can only be used on a flat, level surface.
Caution: You must read this before you proceed
RIGHT ARMCHAIR
Label
A
B
C
D
E
F
G
Picture Description
Right Armrest
QTY
1
Back
Seat
Side Plate
Foot
Seat Cushion
Back Cushion
1
1
1
4
1
1
1 OF 6
Label
①
②
③
④
⑤
⑥
Picture
Before Beginning Assembly:
Description
Allen Key (M6)
Bolt (M6*40mm)
Washer
Allen Key (M4)
Bolt (M6*45mm)
Washer Ring
QTY
1
13
13
1
9
9
2 OF 6
Overview
Right Armrest (A)
Back Cushion (G)
Back (B)
Seat Cushion (F)
Foot (E)
Side plate (D)
Seat (C) FRONT FACING
This Right Armchair has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Right Armchair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1
Open the carton and place all the parts onto a clean, non-marring surface.
Place the Right Armrest(A) with its inside facing up.
Attach Chair Back(B) to the corresponding point in Right Amrest(A) using Bolt( ② ) and
Washer( ③ ) with Allen Key( ① ) as shown above.
Do not fully tigthen.
ATTENTION: There may be some PE wicker that may have covered the Mounting
Points. To ease assembly, guide and slide the PE wicker away from these
Mounting Points.
DO NOT CUT AWAY ANY PE WICKER as this would cause the wicker to unravel!
3 OF 6
Step 2
Attach Seat(C) between the Right Armrest(A) and Back(B) using Bolt( ② ) and
Washer( ③ ) with Allen Key( ① ) from position # I to # V as shown above.
Do not fully tigthen.
Step 3
Attach Side Plate(D) between the Back(B) and Seat(C) using Bolt( ② ) and Washer( ③ ) with Allen Key( ① ) as shown above.
Do not fully tigthen.
Step 4
4 OF 6
Attach the Feet(D) to the Chair using Bolts( ⑤ ) and Washer Rings( ⑥ ) with Allen
Key( ④ ).
Step 5
Turn the Right Armchair right side up.
Place the Right Armchair on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit into to the Right Armchair.
This would help to align all the parts at all the joint areas.
Then get off the Right Armchair, and in a sequential manner, proceed to tighten all bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there is still wobbles, loosen the bolts and execute this same process.
If the Right Armchair is not stable it could lead to damage to the product.
Note: This step is done better with the assistance of a second adult.
Step 6
Place the Back Cushion(G)and Seat Cushion(F) onto the Right Armchair as shown.
Your Right Armchair is ready for use.
Caution:This Right Armchair can only be used on a flat, level surface.
5 OF 6
6 OF 6
Caution : You must read this before you proceed
Dining Table
Label
A
B
C
Picture
Label
①
②
③
Picture
Noble house Home Furnishings LLC
Description
Table Top
Table Leg （ with preinstalled levellers)
QTY
1
2
Leg Connector 1
Description
Allen Key
Bolt (M6*20mm)
Washer Ring
QTY
1
21
21
1 OF 6
Before Beginning
Assembly:
Overview
This Table has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Noble house Home Furnishings LLC
2 OF 6
Step 1
Position the Table Top(A) facedown on a clean, non-marring surface.
Attach Table Leg(B) to Table Top(A) using Bolts( ② ) and Washers( ③ ) with
Allen Key( ① ).
Do not fully tighten the Bolts.
Step 2
Attach the other Table Leg(B) to Table Top(A) using Bolts( ② ) and Washers( ③ ) with Allen Key( ① ).
Do not fully tighten the Bolts.
Noble house Home Furnishings LLC
3 OF 6
Step 3
Insert the Leg Connector(C) between the Table Legs(B).
You may need to apply a little pressure to the Legs - pushing outwards, to enable the Leg Connector(C) to be slotted into position.
Attach Leg Connector(C) to Table Legs(B) using Bolts( ② ) and Washers( ③ ) with Allen Key( ① ), as shown above.
Do not fully tighten the Bolts.
Step 4
Inspect the Table and make sure all parts are adequately connected.
Now, tighten all Bolts at all joints fully in a sequential manner.
Noble house Home Furnishings LLC
4 OF 6
Step 5
Adjust height for balance
Adjust low for balance
Place the Table on a level surface.
Adjust the Legs pre-installed Levellers until the Table is level with the ground.
Step 6
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Noble house Home Furnishings LLC
5 OF 6
Questions & Answers about Proposition 65
• What is Proposition 65?
Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. These chemicals can be in the products that Californians purchase, in their homes or workplaces, or that are released into the environment. By requiring that this information be provided, Proposition 65 enables Californians to make informed decisions about their exposures to these chemicals.
Proposition 65 also prohibits California businesses from knowingly discharging significant amounts of listed chemicals into sources of drinking water.
Proposition 65 requires California to publish a list of chemicals known to cause cancer, birth defects or other reproductive harm. This list, which must be updated at least once a year, has grown to include approximately 900 chemicals since it was first published in 1987.
• What types of chemicals are on the Proposition 65 list?
The list contains a wide range of naturally occurring and synthetic chemicals that include additives or ingredients in pesticides, common household products, food, drugs, dyes, or solvents. Listed chemicals may also be used in manufacturing and construction, or they may be byproducts of chemical processes, such as motor vehicle exhaust.
• What does a warning mean?
If a warning is placed on a product label or posted or distributed at a workplace, a business, or in rental housing, the business issuing the warning is aware or believes that it is exposing individuals to one or more listed chemicals.
By law, a warning must be given for listed chemicals unless the exposure is low enough to pose no significant risk of cancer or is significantly below levels observed to cause birth defects or other reproductive harm.
• Where can I get more information on Proposition 65?
If you have specific questions on the administration or implementation of Proposition 65, you can contact OEHHA's Proposition 65 program at [email protected], or by phone at (916)
445-6900.
Noble house Home Furnishings LLC
6 OF 6
