TECHNICAL DATA PRC-02 PRIMECOAT2 MULTI-PURPOSE PRIMER & SEALER .DESCRIPTION AND USES PRODUCT APPLICATION (cont.) . ® WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-Approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. Zinsser PRIMECOAT2 is a multi-purpose water-based primer and sealer for interior-exterior surfaces. It is a high hiding, low odor primer that dries in 1 hour to a flat, easyto-sand finish. PRIMECOAT2 provides excellent hide for dark colors. It blocks common stains and provides excellent adhesion on even hard to paint surfaces. It flows easily when applied by brush, roller or spray and will work under all topcoats. Priming: Use PRIMECOAT2 to prime drywall, cured plaster, paneling, new and previously painted wood (including exterior plywood and T1-11), concrete, masonry, brick, stucco, trim, clean galvanized or painted metal, glossy laminates and other surfaces. APPLICATION Apply only when air, material, and surface temperatures are between 50-90ºF (10-32ºC) and the relative humidity is below 85%. Thoroughly mix to ensure any settled pigment is re-dispersed before using. Apply with a synthetic brush, roller, pad or sprayer. Follow manufacturer's instructions when using spray equipment. For airless spraying use a 0.017" tip at 2000 to 2500 psi. Wear NIOSH approved respirator and provide adequate ventilation. Sealing: PRIMECOAT2 seals unpainted or porous surfaces, which extends the coverage of topcoat paints. It is an excellent for unpainted or porous surfaces including wood, new drywall, masonry and concrete. PERFORMANCE CHARACTERISTICS . Hides dark colors Excellent for glossy trim Excellent adhesion Seals concrete Excellent for siding .PRODUCTS SKU 323155 323154 THINNING If thinning is necessary, add no more than 10 fluid ounces of clean water per gallon. Note that thinning the primer may affect its stain-blocking properties. . TINTING Description 5-Gallon PRIMECOAT2 1-Gallon PRIMECOAT2 PRODUCT APPLICATION . PRIMECOAT2 can be tinted with up to 2 ounces of universal colorant per gallon. Tinting the primer helps improve topcoat hide. . COVERAGE SURFACE PREPARATION PRIMECOAT2 will cover approximately 300-400 square 2 feet (27-37 m ) per gallon depending upon method of application and surface porosity. Surfaces should be clean, dry, sound and free of dust, dirt, excessive chalky material, grime, grease, oil, wax, mildew, wallpaper adhesive, or any contamination that may interfere with adhesion. If unsure of cleanliness, wash the surface with a low suds cleaning solution like ammonia or a TSP substitute. Rinse thoroughly and allow to dry. On exterior surfaces, remove unsound coatings, and sand paint edges and exposed wood smooth. Kill and remove any mildew. Countersink exposed nail heads, spot prime and fill with spackling compound. Wire brush rusty areas. Clean new galvanized metal with mineral spirits. Spot prime knots and significant water stains with Zinsser B-I-N Primer-Sealer. Use Zinsser Cover Stain to block exterior tannin bleed. Allow new masonry to cure for 30 days prior t application. DRY TIME Dry times are based on 70°F and 50% relative humidity. Dries to the touch in 30 minutes and can be topcoated in 1 hour. Unfinished wood sands to a powder in 1 hour. Full hardness develops in 7-10 days. Lower temperatures, higher humidity, and the addition of tint will prolong dry and cure time. Allow more time at cooler temperatures. CLEAN-UP Clean application tools with warm water and liquid detergent. Follow equipment manufacturer’s directions to clean spray equipment. Dispose of unused or unwanted product in accordance with local laws regulating waterbased coatings. LIMITATIONS PRIMECOAT2 is not recommended for applications to floors or decks or any surface subject to immersion or prolonged contact with water. 1 Form: GDH-1362 Rev.: 051817 TECHNICAL DATA PRIMECOAT2 MULTI-PURPOSE PRIMER & SEALER .PHYSICAL PROPERTIES . Physical Properties PRIMECOAT2 MULTI-PURPOSE PRIMER & SEALER Resin Type Styrene Modified Water-based Acrylic Pigment Type Titanium Dioxide, Calcium Carbonate, Clay Solvents Weight Solids Water, Propylene Glycol Per Gallon 10.4 lbs. Per Liter 1.25 kg By Weight 43.6% By Volume 29.7% <100 g/l (0.83 lbs./gal.) Volatile Organic Compounds Recommended Dry Film Thickness (DFT) per Coat 1.0.1.5 mils (25-37.5µ) Wet Film to Achieve DFT (Unthinned material) 3.5-5.0 mils (87.5-125µ) Practical Coverage at Recommended DFT (assume 15% material loss) Approximately 300-400 sq.ft./gal. (7.4-9.8 m /l) depending on application method and surface porosity Dry Times at 70-80°F (21-27ºC) and 50% Relative Humidity 2 Touch 30 minutes Recoat 1 hour Full Cure Shelf Life 7-10 days 5 years Flash Point >200ºF (93ºC) Safety Information For additional information, see SDS The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice. Rust-Oleum Corporation 11 Hawthorn Parkway Vernon Hills, Illinois 60061 An RPM Company Phone: 877•385•8155 www.rustoleum.com Form: GDH-1362 Rev.: 051817
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021