Cub Cadet 21 in. 208 cc Single-Stage Gas Snow Blower installation Guide
Add to my manuals5 Pages
Cub Cadet 1X 221 LHP is a powerful snow thrower designed for efficient snow removal. It features a 21-inch clearing width and a throwing distance of up to 35 feet. The chute can be rotated 210 degrees to direct snow in the desired direction. The drift cutters help to break up hard-packed snow and ice for easier removal. The headlight provides extra visibility for nighttime operation. With its reliable performance and user-friendly features, the Cub Cadet 1X 221 LHP is an ideal choice for homeowners who need to tackle tough winter conditions.
advertisement
▼
Scroll to page 2
of 5
Assembly & Set-Up Contents of Carton . One Snow Thrower . One Chute Assembly , One Chute Rotation Control Assembly . Two Ignition Keys . One 20 oz, Bottle 5W-30 Oil . One Snow Thrower Operator's Manual » One Engine Operator's Manual . One Pair Drift Cutters (If equipped) NOTE: This Operator's Manual covers several models. Snow thrower features may vary by model. Not all features in this manual are applicable to all snow thrower models and the snow thrower depicted may differ from yours. NOTE: All references to the left or right side of the snow thrower are from the operator's position. Any exceptions will be noted. Unpacking the Snow Thrower 1. Open the top of the carton, 2. Cut down the corners on the front of the carton and fold down the front side, 3. Pull the snow thrower out of the carton. Be sure not to damage the chute, chute rotation control assembly or any cables attached to the chute, Some of these parts are shipped under the shroud on the backside of the carton. Check for any cable ties securing the chute and remove if necessary. Set-Up Adding Fuel & Oil Refer to the Engine Operator's Manual packed with your snow thrower for information on adding fuel and oil. Assembly Positioning the Upper Handle 1. Remove the wing knob and carriage bolt from the top of the lower handle, See Figure 3-1. It is not necessary to remove the shoulder screw and flange lock nut below the wing knob and carriage bolt. 4 N ve oY «— Wing Knob le (0 DB Carriage Bolts A e Wing Knob ua [= DA > 2. Pivot the upper handle into the operating position. Be sure not to pinch any of the cables in the process. See Figure 3-2. Figure 3-1 Figure 3-2 3, On model 221 HP, tighten the previously removed hardware to secure the handle in place. See Figure 3-2. On model 221 LHP proceed with step 4. 4, The handle on model 221 LHP can be set in three different position. Place the handle in the desired position and then install wing knobs and carriage bolts in the appropriate hole and secure the handle. See Figure 3-3. \ Knob Figure 3-3 Installing the Chute 3. Align the holes in the chute base with the holes in the lower chute and secure with the previously removed hex washer screws, See Figure 3-6. 1. On the 221 HP model place the chute handle on the lower chute as shown in Figure 3-4, Skip to step 2 for 221 LHP models, Be certain that the handle is aligned in the channel on the chute and the tabs snap into place. ~ \ \. Figure 3-6 Installing Chute Rotation Control Assembly (Model 227 LHP only) 1. Remave the four hex washer screws from the back of the 2. Remove the hex washer screws in the chute base, See handle (two on each side). See Figure 3-7. Figure 3-5. Figure 3-4 = > Figure 3-7 Figure 3-5 SECTION 3— ASSEMBLY & SEtT-UP 6. Slide the rubber bellow over the universal joint. See Figure 3-10. ( » 2. Using the four hex washer screws, install the chute rotation control assembly, See Figure 3-8. @ ` N и 3. Figure 3-8 Remove the screw and hex lock nut from the universal joint, See Figure 3-9, и Hex Lock Nut a Chute Rod / Screw Figure 3-9 NOTE: Make sure the chute Is facing forward when installing the universal joint. Install the universal joint on the end of the chute rod as shown in Figure 3-9, NOTE: Be sure the holes in the universal joint line up with the holes in the chute rod. You may have to activate the trigger to allow you to line up the holes, Secure the universal joint with the hex nut and screw previously removed. See Figure 3-9. Figure 3-10 Installing the Recoil Starter Handie 1. Remove the eye bolt and handle knob from the manual bag. 2. Place the eye bolt and handle knob on the upper handle as shown in Figure 3-11, Do not fully tighten the hardware until instructed to do so. Recoil Starter Handle, y y $ YY = Eds, Y TE Figure 3-11 NOTE: The opening of the eye bolt should face toward the back of the snow thrower. 3. Slowly pull the recoil starter handle up towards the eye bolt, 4, Slip the recoil starter rope into the eye bolt from the back of the snow thrower, See Figure 3-11, 5, Securely tighten the eye bolt and handle knob. SECTION 3 — AssemeLy €: SET-Up 9 10 Installing the Drift Cutters (if equipped) 1. Remove the drift cutters from the manual hag. 2. Remove the flange lock nut and carriage bolt installed into each drift cutter, 3. Using the previously removed hardware, install the drift cutters onto the auger housing as shown in Figure 3-12, Figure 3-12 SECTION 3— Assemeaiy & Sec-Up Controls & Features 7 Chute Assembly Drift Cutter N Auger Shave Plate \. NOTE: This Operator's Manual covers several models, Snow thrower features may vary by model, Not all features In this manual are applicable to all snow thrower models and the snow thrower depicted may differ from yours. All references to the left or right side of the snow thrower are from the operator's position. Any exceptions will be noted, Recoil Starter Handle The recoil starter handle is used to manually start the engine. EZ Chute (Model 221 HP) The rotation of the chute is controlled by rotating the chute control handle left or right, The angle/distance that snow is thrown Is changed by manually tilting the upper chute to the desired position, Shave Plate The shave plate maintains contact with the pavement as the snow thrower is propelled, allowing snow close to the pavements surface to be discharged. Chute Tilt Control (Model 221 LHP) The chute tilt control is located to the right of the control panel and controls the angle/distance that snow is thrown. Pull back on the chute tilt control to increase the angle/distance and push forward to decrease the angle/distance, Headlight 4 Auger Control Chute Rotation Control _/ Chute Rotation Control (Model 221 LHP) The chute rotate control is located in the center of the control panel and controls the direction snow is thrown, Depress the button and rotate the chute rotation control to the right to turn the chute to the right and rotate to the left to turn the chute to the left, Auger When engaged, the auger rotation draws snow into the auger housing and throws it out the discharge chute. Rubber paddles on the auger also ald in propelling the snow thrower as they come in contact with the pavement. Auger Control Located on the upper handle, the auger control is used to engage and disengage drive to the auger. Squeeze the control against the upper handle to engage the auger; release it to disengage. Drift Cutters (If equipped) The drift cutters are designed for use in deep snow, Their use is optional for normal snow conditions. Maneuver the snow thrower so that the cutters penetrate a high standing snow drift to assist snow falling into the augers for throwing. Headlight (Model 221 LHP} The headlight is located on the upper center of the control panel and is on when the snow thrower is running. 11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project