Winflo WRE006B36D, WR052C36DF, WR004C36F, WRE005B30D, WR055C30DR, WR001C36F, WR001B30D, WR055C30DRF, WR002B30L, WR055C36DR Operating instrustions

Winflo WRE006B36D, WR052C36DF, WR004C36F, WRE005B30D, WR055C30DR, WR001C36F, WR001B30D, WR055C30DRF, WR002B30L, WR055C36DR Operating instrustions
 LIMITED WARRANTY
This warranty extends to the original purchaser only. This warranty is not transferable,
between homes or owners and is only applicable to residential use. Winslyn
Industries, LLC provides a 3-year limited parts warranty for all range hoods. Under
this warranty, you (the customer), is entitled to replacement parts at no cost to
repair and restore functionality if any part of the product were to fail. No labor is
provided. Certain consumables that are not covered under this warranty include
Lights (halogen and LEDs), Carbon Filters, Mesh or Baffle Filters, Ducting. These
parts are guaranteed to last one year beginning from the date of purchase. If they
fail prematurely or are defective within 1 year of purchase, we will replace them
at no charge. If a main unit or complete replacement needs to be sent, Winslyn
Industries, LLC will require that the customer pay for shipping. Shipping for parts
are free under the warranty period. We will provide replacement parts at no charge
under normal use and service. We provide you with complete instructions on how
to maintain and care for this product. We will not be responsible for due to lack of
maintenance or proper use. The original sales receipt, order number, and/or proof
of purchase must be presented at the time of the warranty claim, without exception.
As noted in the instructions we recommend the use of a professional installer.
Winslyn Industries, LLC will not be held responsible for any damage or product
failure due to improper installation, misuse, or failure to use a licensed professional.
This warranty only extends for household product use, this warranty will be void
for commercial use of this product. This warranty will not be applicable if product
is purchased from an unauthorized seller. By purchasing this product, buyer agrees
that we are not liable for incidental, consequential, or special damages associated
with the return, replacement, installation or use of your product. This includes
freight costs, labor, travel time, lost profit, home damages and other contingent
liabilities and costs (including, without limitation, costs associated with experts,
investigations, analyses, attorneys and other professionals and services). Our
warranty is a comprehensive and explicit limit of liability, and all items outside of
it are not addressable by or the responsibility of Winslyn Industries, LLC. Certain
states have variances regarding implied warranties and in those situations, we
remain fully compliant. We make no implication that products comply with any or
all local building or plumbing codes. Itis the consumer's responsibility to determi
ne local building code. Please write or contact us at:
Winslyn Industries, LLC
1232 Hardt Circle
Bartlett, Illinois 60103 Winpro® Sinks Winflo® Range Hoods
Email: [email protected] Winette® Bathroom Vanities
18
\Winflo
Range Hoods
Installation Instructions,
Maintenance, Use
and Warranty
INSTRUCTIONS FOR MODELS:
W101, W102, W103, W104, WE105, WE106, WE107,
WR001, WRO02, WRO03, WRO04, WRE005, WREO06, WRE007
CD.
Intertek
IMPORTANT: READ AND SAVE THESE INSTRUCTIOMS.
FOR RESIDENTIAL USE ONLY.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
READ THE FOLLOWING:
=
Y
vw
>
>
Use this unit only in the manner intended by the manufacturer. If you have
questions, please contact the manufacturer.
Before servicing or cleaning the unit, switch the power off and turn power off
at the electrical panel and lock the service panel. This will prevent the power
from accidentally turning on. If the service panel does not lock, secure a warning
label, such as a tag, to the service panel.
Installation work and electrical wiring must be done by a qualified professional(s)
in accordance with all applicable codes, standards, and fire-rated constructions.
Do not operate any fans with a damaged cord or plug. Discard the fan or return
to an authorized service facility for further examination and/or repair.
To prevent back draft, sufficient air is needed for proper combustion. Gas from
the fuel burning equipment needs to exhaust through the flue (chimney). Follow
the heating equipment manufacturer's guideline and safety standards such as
those published by the National Fire Protection Association (NFPA), the
American Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
When cutting, or drilling into walls or ceilings; be aware of electrical wires,
piping, and other utilities.
Ducted fans must always be vented outdoors.
CAUTION: For general ventilation use only. Do not use to exhaust hazardous or
explosive materials and vapors.
CAUTION: To reduce the risk of fire and to properly exhaust air, be sure to duct air
outside — DO NOT vent exhaust air into attics, crawl spaces, garages, or within walls
and ceilings.
WARNING: TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE, READ THE
FOLLOWING:
ho
”
Y
Never leave surface units unattended at high settings. Boil-over can cause
smoke and grease to spill over that may ignite. Heat oils slowly on low or
medium settings.
Always turn range hood ON when cooking at high heat or when cooking food
with high flames.
Clean ventilation fans frequently. Grease should not be allowed to accumulate
on fan or filter.
Use proper pan size. Always use cookware appropriate for the size of the
surface element.
WARNING: TO REDUCE THE RISK OF INJURY, IN THE EVENT OF A RANGE TOP GREASE
FIRE, READ THE FOLLOWING:
» SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn
off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out
immediately. EVACUATE AND CALL THE FIRE DEPARMENT.
> NEVERPICK UP A FLAMING PAN — you may be burned.
> DO NOT USE WATER, including wet dishcloths or towels —a violent steam
explosion will result.
> Usean extinguisher ONLY if:
-You know you have a class ABC extinguisher, and you know how to operate it.
-The fire is small and contained in the area where it started.
-The fire department is being called.
-You can fight the fire with your backto an exit.
Based on “Kitchen Fire Safety Tips” published by NFPA
WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any
solid-state speed control device.
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician
install the range hood. Itistheinstaller's responsibility to comply with installation
clearances specified on the model/serial rating plate. Canopy hood's location
should be away from strong draft areas, such as windows, doors, and strong heating
vents. Cabinet opening dimensions that are shown must be used. Given dimensions
provide minimum clearance.
| ELECTRICAL REQUIREMENTS
Observe all governing codes and ordinances. Ensure that the electrical installation
is adequate and in conformance with the National Electrical Codes, ANSI/NFPA 70
(latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition), all local codes, and ordinances. If codes permit
and a separate ground wire is used, it is recommended that a qualified electrician
determine that the ground path is adequate.
A copy of the above code standards can be obtained from:
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.
If the house has aluminum wiring, follow the procedure below:
o Connectasection of solid copper wire to the pigtail leads.
o Connectthe aluminum wiring to the copper wire using special connectors
and/or tools designed and UL listed for joining copper to aluminum. Follow
the manufacturer's recommended procedure for the electrical connector.
Aluminum/copper connection must conform to local codes and industry
accepted wiring practice.
» Wire sizes and connections must conform to the rating of the appliance as
specified on the model/serial rating plate. The model/serial plate is located
behind the filter on the rear wall of the range hood.
Wire sizes must conform to the requirements of the National Electrical Code,
ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical
Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.
Y Y
<
#
Y
VENTILATION REQUIREMENTS
General requirements
> Range hoods must be ventilated to the outdoors, except for non-vented
(recirculating) installations.
Do not ventilate the range hood into an attic or other enclosed areas.
Do notuse 4” (10.2 cm) laundry-type wall caps.
The length of the range hood and the number of elbows should be kept to a
minimum to provide maximum performance.
Y Y Y
For the most efficient and quiet operation
# Useno more than three 90-degree elbow.
> Make sure there is a minimum of 24” (61 cm) of straight duct between the
elbows if more than one elbow is used.
» Donotinstall two elbows together.
= Useclamps and tape to seal all joints in the vent system.
> The vent system must have a damper. If the roof or wall cap has a damper, do
not use the damper supplied with the range hood.
> Use caulking to seal exterior walls or roof openings around the cap.
> The size of the vents should be uniform.
Cold Weather Installations
An additional back draft damper should be installed to minimize backward cold air
flow. A thermal break should be installed to minimize conduction of outside
temperatures as part of the vent system. The damper should be on the cold air side
of the thermal break. The break should be as close as possible to where the vent
system enters the heated portion of the house.
Makeup Air
Local building codes may require the use of makeup air systems, when using
ventilation systems greater than specified CFM of air movement. The specified
CFM varies from state to state. Consult your HVAC professional for specific
requirements in your area.
Venting Method
To vent through a wall, a 90-degree elbow is needed. If exhaust ducting with a
diameter of less than 5.91” (150 mm) or if flat ducting is used, the noise level of the
range hood could increase and extraction will be less efficient.
Rear Discharge
A 90-degree elbow may be installed immediately above the hood.
For Non-Vented (recirculating) Installations
Ifitis not possible to vent cooking fumes and vapors to the outside, certain hoods
can be used in the non-vented (recirculating) version, fitting a carbon filter at the
motor. Fumes and vapors are the recycled through the top grille. DO NOT block
the chimney holes.
Calculating Vent System Length
To calculate the length of the system you need, add the equivalent feet (meters)
for all vent pieces used in the system.
INSTALLATION DIMENSION RECOMMENDATIONS
1
For wall mount range hoods:
A. Countertop Height.
B. Hood height from ceiling to bottom of the range hood filter surface: D-A-C=B.
C. 24" minimum from cooking surface up to 36” maximum for Electric/Induction
range tops. 27” minimum from cooking surface up to 36” maximum for Gas
range tops.
D. Floor to ceiling height.
Prior to installation
> Unpackrange hood and ensure all listed parts are in the box.
7 ltisrecommended for the vent system to be installed before hood is installed.
> Before making cutouts, make sure there is proper clearance within the ceiling
or walls for the exhaust vent.
Determine which venting method to use: roof or wall.
Itis recommended that a professional installer perform the range hood installation.
Y Y
Э
Exhibit A
— A
Roof venting NR
Wall venting
A
A. Roof cap A. Wall cap
B.6"(15.2cm) B.6“(15.2cm}
round vent round vent
INSTALLATION INSTRUCTIONS for Wall Mount
Range Hood
Parts supplied (Note: The fasteners included may not be suitable to your wall
structure. Please check with the installer on proper fasteners to be used based
on the material makeup of your wall)
A.
B.
Es
+
FA e
+
<
LG) mm
Range Hood
Power Cord (attached to range hood)
6” or 8” round vent air flap depending on model. (attached to range hood on
top of unit)
(2) Drywall Anchor (Wall anchors will vary depending on wall material and the
weight of the range hood being installed. They can be found at any home
improvement store)
(2) 1-3/16 drywall anchor screw
(2) #10 X 3/4 tapping screw
Aluminum or Stainless Steel Filters (attached to the bottom of the range hood)
Duct brackets: Certain Models have 2 brackets w/4 screws attached, Certain
Models have 1 bracket w/2 screws attached
(1) 6” or 8” round flexible duct exhaust hose, depending on model
(2) Stainless Steel Ducts (inner and outer)
(2) #6 X 3/8 SM Screw
(2) rubber bumpers and (2) screws. Note: Some models may have bumpers
preinstalled. You may not need the included screws on some models
Some models may have a pre-installed grease collection tray. Some models
may not have a grease collection tray
im
Zu
&-——
Parts not supplied
» Ducttape
> Preinstalled ventilation system and ductwork
> Preinstalled outside duct cap or weatherproofing
)
| |
И
E
I
|
|
i \
|
|
M
|
to
Um iy
|
a
| il
|
1 A
AO
|
|
TT
|
||
|
TIA
I fh
| М
|
|
\
|
LAN
у
es
a
(
Installing the range hood
This installation is for mounting the product to a wall. Ensure your wall
has the proper support to hold the range hood weight. These instructions
are general guidelines, please consult your installation specialist regarding
the best type of mounting hardware and support system based on your
wall construction. All wall mounted range hoods, if possible, should be
installed and supported by studs behind the wall (hardware not included).
In the event studs are not in alignment with the wall mount mounting plate
holes, a wooden cross support system will need to be retrofitted to your
existing studs. All homes are different and installations will vary.
de
2:
Begin installation by removing the filters (G) and removing any tape on the air
flow flappers (C).
Remove protective film from range hood and ducting. When handling the
ducting please wear protective gloves to avoid sharp edges.
If your model has an electronic touch sensor control panel, remove the protective
plastic film covering the control panel.
Insert the rubber bumpers (L) by attaching to the back of range hood at the
two outside locations. For some models, you will need to remove the two
outside screws, place bumper over hole and reattach the screw. See below.
Some models have the bumper already attached.
| @ . D e
me pri
Some models, due to packaging needs, may come with the mounting brackets
attached to the back of the range hood inverted and attached with screws (see
below).
1) Unscrew and reverse mounting brackets
NE 5 — =
о
0 C
2) Screw in mounting brackets, as shown below, using screws removed in step 1
В
10.
Find the center of the wall where you are installing the hood. Mark your center
line to the ceiling and measure out from the center to find your two mounting
points. The (2) mounting holes will be found on the back of the range hood
(the mounting holes will vary by model). Make sure your mounting points are
CEILING
level when you mark them.
1. CENTER LINE
? CHIMNEY 1. MOUNTING
WIDTH SCREWS
Mark your mounting points and install the drywall anchors (D) turning until
they are flush to the wall, do not overturn. Screw the (2) 1-3/16 drywall anchor
screw (E) into the drywall anchor (D) leaving the heads out 4” to mount the
hood. See Below.
Temporarily position the range hood in the desired mounting location on the
wall (this will require 2 people). See below.
*To properly secure the range hood, identify a
stud{s) and drill though the back of the range
hood at stud location and secure with a wood
screw(s) (not included)
uy
a
Make sure the range hood is level. Finish screwing the (2) 1-3/16 drywall anchor
screw (E) from step 5. Do not over tighten.
From the center line drawn in step 5, center the mounting bracket (H) at the
top of the ceiling and insert (2) #10 X 3/4 tapping screws (F) into the horizontal
holes and attach to the wall. See below.
11. Assemble ventilation to outside ducting. Install (1) round flexible duct exhaust
hose (I) to round vent air flap (C) (attached to range hood on top of unit) and
secure with duct tape. Note: If you are choosing the ductless/recirculating
mode do not install the duct exhaust hose (I).
12. Powerthe hood by connecting the three-pronged plug to a nearby electrical
outlet.
13. For models with one mounting bracket (H), place the two pieces of Ducting (J)
on top of the range hood, making sure the vent in the upper section is towards
the top and the upper section slides inside the lower section in a telescoping
fashion, note the grooves on the inside of the duct work to help guide and
secure. Lower the top duct into the bottom duct. See below. Go to step 14.
o
|
14. For models with two mounting brackets (H), remove the upper section from
the bottom section.
T
a) Remove screws from duct bracket (H). Insert mounting bracket inside of
the bottom duct and align the holes. Replace the screws entering the back
of the duct. This mounting bracket is for support of the ducts.
A
Mounting bracket goes inside the duct
10
b) Reinsertthe top duct of the range hood into the bottom duct. Please
ensure that the 2 outer edges of the top half slide between the mounting
bracket (H) and inside walls of the bottom half. This is needed to ensure
stability of the top half of the duct. Lower the top duct into the bottom
duct.
15. Place the two pieces of ducting (J) on top of the range hood. Insert the bottom
section of the duct (J) to the top of the range hood and insert (2) #6 X 3/8 SM
screws (K) through the outer panel of the duct to the holes aligned on the range
hood and tighten.
16. Once the bottom duct is secured, slowly slide the top duct towards the ceiling.
Attach (2) #6 X 3/8 SM screws from the outside of the ducting to the bracket
installed in step 9.
17. Turnonunitand proceed to operating instruction. Note: There is a protective
film covering the touch control panel. Please remove this film.
11
FILTER INSTALLATION FOR DUCTLESS (RECIRCULATING)
MODE
IMPORTANT: If you are choosing the ductless/recirculating mode do not install the
duct exhaust hose (I).
1. Unplugthe power cord.
2. Remove the filter panel(s) located at the bottom of the range hood.
3. Locatethe motorized fan inside the hood.
4. Attach the carbon filters (not included, can be purchased: Part number
WRHF001S2) to both sides of the motorized fan.
5. Twist the carbon filter until itis in the locking position (separate instructions
included with filters).
6. Reinstall the filter panel(s), and reconnect the power.
OPERATING INSTRUCTIONS
Note: There are different operating instructions based
on the control panel for your model. Please choose
the operating instruction for your unit.
Powering on/off the unit
OOOOO
Tx se Je a d
@ ® @ © ©
1 2 3 4 5 1 2 3 4 5
> Toturnthe fan on push a button to select one of the 3 speeds:
o 2=High
o 3=Medium
o 4=Low
If you choose a new speed by pressing a different button, the new fan speed
will replace the old fan speed.
>= Toturn fan off push button 5
> To operate light on/off push button 1 (Note: The fan and light operate
independently of each other)
12
Power/
Lamp Timer Minus Plus Fan Standby
» Lamp: Press the lamp display one time to activate the light, press the lamp
display again to deactivate it.
> Power/Standby: When the range hood is in the “original” state, touch this
button. It will enter the standby mode.
> Setting the clock: When the range hood is on “Standby” Mode, press and hold
the timer button for 3 seconds. The range hood will then enter the time setting
state; the display screen will show numbers. Press the Plus to set hours and
Press the Minus to set the minutes. After 10 seconds, it will automatically exit
the time setting state and the time you have entered will be saved.
» Timer:
o Whenthe fans are operating, touch the timer button one time. This will
turn on the timer mode and the display with show 03:00. Each time you
press the timer button, it will increase by 1 minute with the maximum
timer setting of 60 minutes. Within the last 3 seconds of the timer setting,
the range hood will make three beeps.
o When range hood is on, touch the Power/Standby once and the shut off
timer will set to 60 seconds. Touch the button twice and the fan will turn
off.
» Fan Operation (this control panel comes with either a 3-speed or 5-speed fan):
o For 3-speed fan:
+ Instandby mode, press the Minus button one time and the range hood
will start at F1 speed. If the button is pressed again, the speed will stay
the same.
» Instandby mode, press the Plus button one time, the range hood will
start at F3 speed. If the button is pressed again, the speed will stay the
same.
* Tolower or increase the fan speed press the Plus or Minus buttons.
» When fan is in the standby mode, press the Fan button to reach
maximum speed immediately. Touching this button while in a lower
speed will automatically take to the maximum speed. Touching the
Fan button twice will turn the fan off.
o For5-speed fan:
+ Instandby mode, press the Minus button one time and the range hood
will start at F1 speed. If the button is pressed again, the speed will stay
the same.
13
* Instandby mode, press the Plus button one time, the range hood will
start at F6 speed for 5 seconds for an initial suction burst then it will
automatically reduce to F5 speed. If the button is pressed again, the
speed will stay the same.
* Tolowerorincrease the fan speed press the Plus or Minus buttons.
* When fan is in the standby mode, press the Fan button to reach
maximum speed immediately. Touching this button while in a lower
speed will automatically take to the maximum speed. Touching the
Fan button twice will turn the fan off.
Powering on/off and Settings:
14
Fan Power/Standby
Lamp Timer Clock
Lamp: Press the lamp display one time to activate the light, press the lamp
display again to deactivate it.
Power/Standby: When the range hood is in the “original” state, touch this
button. It will enter the standby mode.
Setting the clock: When the range hood is on “Standby” Mode, press and hold
the timer button for 3 seconds. The range hood will then enter the time setting
state; the display screen will show numbers. Press the Fan button to set hours
and press the Lamp button to set the minutes. After 10 seconds, it will
automatically exit the time setting state and the time you have entered will be
saved, or press the Timer button to exit and keep saved time.
Fan Operation:
o Instandby mode, press the Fan button one time and the range hood will
start at F3 speed. If the Fan button is pressed again, the speed will reduce
to F2. Ifthe Fan button is pressed again, the speed will reduce to F1.
Pressing the Fan button after the F1 setting will shut off the fan.
Timer:
o Whenthe fans are operating, touch the Timer button one time. This will
turn on the timer mode and the display with show a flashing 03:00, after
8 seconds the display will stop flashing and begin counting down. Each
time you press the timer button, it will increase by 1 minute with the
maximum timer setting of 60 minutes. Within the last 3 seconds of the
timer setting, the range hood will make three beeps.
o Whenrange hood ison, touch the Power/Standby once and the shut off
timer will set to 60 seconds. Touch the button twice and the fan will turn
off.
Timer Lamp Fan Clock
il Tn
Fan Speed Power/Standby
Lamp: Press the lamp display one time to activate the light, press the lamp
display again to deactivate it.
Power/Standby: When the range hood is in the “original” state, touch this
button. It will enter the standby mode.
Setting the clock: When the range hood is on “Standby” Mode, press and hold
the timer button for 3 seconds. The range hood will then enter the time setting
state; the display screen will show numbers. Press the Fan button to set hours
and press the Lamp button to set the minutes. After 10seconds, it will
automatically exit the time setting state and the time you have entered will be
saved, or press the Timer button to exit and keep saved time.
Fan Operation:
Oo Instandby mode, press the Fan button one time and the range hood will
start at high speed (all nine bars will be illuminated on the fan speed bar).
If the Fan button is pressed again, the speed will reduce to medium (six
bars will be illuminated). If the Fan button is pressed again, the speed will
reduce to low (three bars will be illuminated). Pressing the Fan button
after the low speed setting will shut off the fan.
Timer:
o Whenthefans are operating, touch the Timer button one time. This will
turn on the timer mode and the display with show a flashing 01:00, after
8 seconds the display will stop flashing and begin counting down. Each
time you press the timer button, it will increase by 1 minute with the
maximum timer setting of 60 minutes. Within the last 3 seconds of the
timer setting, the range hood will make three beeps.
o When range hood is on, touch the Power/Standby once and the shut off
timer will set to 60 seconds. Touch the button twice and the fan will turn
off.
15
CARE and MAINTENANCE
Cleaning
IMPORTANT: Clean the hood and panel filters frequently per the following
instructions. Replace the panel filters before operating hood.
Exterior Surfaces
To avoid damage to the exterior surface, do not use steel wool or soap filled scouring
pads. Always wipe dry to avoid water marks.
Cleaning Method
Use liquid mild-detergent soap and water, do not use hard abrasive cleaners.
Wipe with damp soft cloth or non-abrasive sponge, then rinse with clean water
and wipe dry.
Do's:
* Cleanyourrange hood using a non-abrasive cloth or sponge and liquid detergent.
* Always wipeinthe direction of the grain pattern.
= Aftercleaningrinse with water.
Make sure range hood is dry after cleaning.
Don'ts:
* Do not use steel wool or like products as this will cause scratching and iron
residue that could lead to rusting and corrosion.
* Donotwipeagainstthe grain pattern as this will impact the original finish.
* Donotuse chlorine bleach.
Grease/Baffle Filter
* Remove the filter by pulling the spring release handle and then pulling down
the filter.
* Woashfilters as needed in dishwasher or hot detergent solution (low temperature,
short cycle).
* If your model has a grease tray, please remove, drain and clean periodically.
* Makesure filters are completely dry before putting back into range hood.
* Reinstall the filter by making sure the spring release handles are toward the
front. Insert filter into upper track.
® Pushthe spring release handle.
* Pushuponfilter and release handle to latch into place.
Grease Tray (If your model contains)
* Periodically remove the grease tray (M) and clean built up grease collection.
16
Replacing the LED light (Replacement Bulb Part Number: WRHLB152)
Turn off the range hood and allow the LED light to cool.
To avoid damage or decreasing the life of the new bulb, do not touch bulb with
bare fingers. Replace bulb wearing cotton gloves to handle bulb.
If new LED light does not operate, make sure the lamps are inserted correctly
before calling for support.
To replace:
NOU EWN
Disconnect the power cord to ensure unit does not turn on.
Remove filters.
Reach behind the light and push towards you until the light pops out.
Disconnect the electrical harness.
Attach new bulbs to the electrical harness.
Snap bulbs back into unit and replace filters.
Reconnect the power cord.
Electrical harness connection
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement