null  null
CD RDS RECEIVER
AUTORADIO CD RDS
REPRODUCTOR DE CD CON RECEPTOR RDS
DEH-80PRS
Installation Manual
Manuel d’installation
Manual de instalación
Section
Connections
Connections
WARNING
! Use speakers over 50 W (output value) and
between 4 W to 8 W (impedance value). Do
not use 1 W to 3 W speakers for this unit.
! The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire first.
Ensure that the ground wire is properly connected to metal parts of the car’s body. The
ground wire of the power amp and the one of
this unit or any other device must be connected to the car separately with different
screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.
Ground wire
Other devices
(Another electronic
device in the car)
POWER AMP
Metal parts of car’s body
F
O
N
OF
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
ACC position
STAR
T
01
No ACC position
! Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire or malfunction.
! To prevent a short-circuit, overheating or malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the battery before installation.
— Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.
— Place all cables away from moving parts,
such as the shift lever and seat rails.
— Place all cables away from hot places, such
as near the heater outlet.
— Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power with
other devices. The current capacity of the
cable is limited.
— Use a fuse of the rating prescribed.
— Never wire the negative speaker cable directly
to ground.
— Never band together negative cables of multiple speakers.
! When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
! Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
This unit
Power cord
9
3
4 56
a b
4
2
1
d
1
L
78
c
1 USB port 1
2 USB port 2
3 Antenna input
15 cm (5-7/8 in.)
4 Audio input
5 Fuse (10 A)
6 Power cord input
7 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
8 Microphone input
9 Microphone
4 m (13 ft. 1 in.)
a Rear output or high range output
b Front output or middle range output
c Subwoofer output or low range output
d USB cable
1.5 m (4 ft. 11 in.)
! If connecting both USB1 (USB storage
device1)/iPod1 (iPod connected using
USB input1) and USB2 (USB storage device2)/iPod2 (iPod connected using USB
input2) at the same time, use a Pioneer
USB cable (CD-U50E) in addition to the
regular Pioneer USB cable.
R
2
3


F/M

5

R/H

6
7
8
9
a
b
c
d



e
f
g
h
i
1
2
3
4
5
6
7
8
9
a
b
c
d
e
f
g
h
i
To power cord input
Left
Right
Front speaker or middle range speaker
Rear speaker or high range speaker
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black (chassis ground)
Connect to a clean, paint-free metal location.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by ignition
switch (12 V DC).
Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).
Orange/white
Connect to lighting switch terminal.
Section
Connections
Power amp (sold separately)
Standard mode with internal amp
Important
! Change the DSP switch to standard mode
(STD).
For more details on change settings, refer to
the operation manual or Switching the DSP
setting mode on this page.
! The following signals are output from the
speaker leads when this connection is in
use.
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left +
Green/black: Rear left *
Violet: Rear right +
Violet/black: Rear right *
3
1
2
5




01
Connections
4
5
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cable (sold separately)
4 To subwoofer output
5 Subwoofer
Standard mode without internal
amp
Important
! Change the DSP switch to standard mode
(STD).
For more details on change settings, refer to
the operation manual or Switching the DSP
setting mode on this page.
! If using this system, we recommend that this
unit’s internal amp is turned off.
For details, refer to the operation manual.
! The speaker leads are not used when this
connection is in use.
3
1
2
5




5




7
3
1
9
2




2
5
8
9
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cable (sold separately)
4 To Rear output
5 Rear speaker
6 To Front output
7 Front speaker
8 To subwoofer output
9 Subwoofer
3-way network mode with
internal amp
Important
! Change the DSP switch to 3-way network
mode (NW).
For more details on change settings, refer to
the operation manual or Switching the DSP
setting mode on this page.
! The following signals are output from the
speaker leads when this connection is in
use.
5








7
4
5
3
2
1




6
7
3
2
6
3
1
3
1
3
2
1
7
4
White: Middle range left +
White/black: Middle range left *
Gray: Middle range right +
Gray/black: Middle range right *
Green: High range left +
Green/black: High range left *
Violet: High range right +
Violet/black: High range right *
4
5
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cable (sold separately)
4 To low range output
5 Low range speaker
3-way network mode without
internal amp
Important
! Change the DSP switch to 3-way network
mode (NW).
For more details on change settings, refer to
the operation manual or Switching the DSP
setting mode on this page.
! If using this system, we recommend that this
unit’s internal amp is turned off.
For details, refer to the operation manual.
! The speaker leads are not used when this
connection is in use.
1
9
2




8
9
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cable (sold separately)
4 To high range output
5 High range speaker
6 To middle range output
7 Middle range speaker
8 To low range output
9 Low range speaker
Switching the DSP setting mode
This unit features two operation modes: the 3way network mode (NW) and the standard mode
(STD). You can switch between modes as desired. Initially, the DSP setting is set to the
standard mode (STD).
! After switching, reset the microprocessor.
WARNING
Do not use the unit in standard mode when a
speaker system for 3-way network mode is connected to this unit. This may cause damage to
the speakers.
Section
01
Connections
Installation
02
1 Use a thin, flathead screwdriver to
change the DSP switch on the bottom of this
unit.
If connecting the unit to a car
stereo with no RCA output
1
2 Press RESET with a pen tip or other
pointed instrument.
For details, refer to the operation manual.
2
3
4
5
6
7
8
1
2
3
4
5
6
7
Car stereo with no RCA output
To speaker output
Red: Right +
Black: Right *
Black: Left *
White: Left +
Speaker-RCA conversion cable (supplied)
19 cm (7-1/2 in.)
8 To audio input
Important
! Check all connections and systems before
final installation.
! Do not use unauthorized parts as this may
cause malfunctions.
! Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
! Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
! The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
Use commercially available parts when installing.
DIN Front-mount
1 Insert the mounting sleeve into the dashboard.
For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space,
use the mounting sleeve that came with the vehicle.
2 Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°) into
place.
1
Audio input
If you connect the unit to an audio device with
RCA output, or to one with no RCA output, you
can set it up so that the audio from the audio device is output through speakers connected to
the unit. Change settings as necessary based on
whether the connected device has RCA output
or not.
For more details on change settings, refer to the
operation manual or Switching between RCA
input modes on this page.
Switching between RCA input
modes
% Use a thin, flathead screwdriver to
change the RCA input mode switch on the
bottom of this unit.
3
4
1
1
2
3
4
Car stereo with RCA output
To audio output
Connect with RCA cable (sold separately)
To audio input
2
! When installing, to ensure proper heat dispersal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not blocking the vents.
1 Dashboard
2 Mounting sleeve
3
Install the unit as illustrated.
1
2
If connecting the unit to a car
stereo with RCA output
2
60°
3
! L (Low) - If inputting from the RCA output of a
connected device
! H (High) - If inputting from the speaker output of a connected device
Leave ample
5 cm
space
5 cm
4
5
5cm
cm
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
1
2
3
4
5
Nut
Firewall or metal support
Metal strap
Screw
Screw (M4 × 8)
Section
Installation
Installation
# Make sure that the unit is installed securely in
place. An unstable installation may cause skipping
or other malfunctions.
! Releasing the front panel allows easier access to the trim ring.
! When reattaching the trim ring, point the
side with the notched tab down.
1 Attach the holders to both sides of the
front panel.
DIN Rear-mount
1 Determine the appropriate position
where the holes on the bracket and the side
of the unit match.
2 Insert the supplied extraction keys into
both sides of the unit until they click into
place.
3
Pull the unit out of the dashboard.
1 Holder
2
Replace the front panel to the unit.
3
Flip the holders into upright positions.
3
1
Removing and re-attaching
the front panel
2
1
2
3
!
Screw
Mounting bracket
Dashboard or console
Use either truss (5 mm × 8 mm) or flush surface (5 mm × 9 mm) screws, depending on
the bracket screw holes.
Removing the unit
1
2
Tighten two screws on each side.
Remove the trim ring.
You can remove the front panel to protect your
unit from theft.
Press the detach button and push the front
panel upward and pull it toward you.
For details, refer to operation manual.
Fastening the front panel
If you do not plan to detach the front panel, the
front panel can be fastened with supplied
screws and holders.
4 Fix the front panel to the unit using fixing screws.
1 Trim ring
2 Notched tab
1 Screw
02
Section
03
Installing the microphone
Installing the microphone
2 Install the microphone clip on the steering column.
1
CAUTION
It is extremely dangerous to allow the microphone lead to become wound around the steering column or shift lever. Be sure to install the
unit in such a way that it will not obstruct driving.
1
Note
Install the microphone in a position and orientation that will enable it to pick up the voice of the
person operating the system.
When installing the
microphone on the sun visor
1 Install the microphone on the microphone clip.
1
2
2
2
1 Microphone clip
2 Clamp
When installing the
microphone on the steering
column
1 Install the microphone on the microphone clip.
1
2
1 Microphone
2 Microphone clip
2 Install the microphone clip on the sun
visor.
With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the voice
recognition rate.)
3
3
4
1 Microphone
2 Microphone base
3 Microphone clip
4 Fit the microphone lead into the groove.
# Microphone can be installed without using microphone clip. In this case, detach the microphone
base from the microphone clip. To detach the microphone base from the microphone clip, slide the microphone base.
1 Double-sided tape
2 Install the microphone clip on the rear side of
the steering column.
3 Clamp
Adjusting the microphone
angle
The microphone angle can be adjusted.
Section
Connexions
Non fourni avec cet appareil.
PIONEER CAR STEREOS
O
Avec position ACC
STAR
*1
F
N
*1
Important
! Lors de l’installation de cet appareil dans un
véhicule sans position ACC (accessoire) sur
le contact d’allumage, ne pas connecter le
câble rouge à la borne qui détecte l’utilisation de la clé de contact peut entraîner le déchargement de la batterie.
OF
ATTENTION
! Utilisez des haut-parleurs avec une puissance de sortie de 50 W et une impédance
de 4 W à 8 W. N’utilisez pas des haut-parleurs
d’impédance 1 W à 3 W avec cet appareil.
! Le câble noir est la masse. Lorsque vous installez cet appareil ou un amplificateur de
puissance (vendu séparément), assurez-vous
de connecter le fil de masse en premier. Assurez-vous que le fil de masse est connecté
correctement aux parties métalliques de la
carrosserie du véhicule. Le fil de masse de
l’amplificateur de puissance et celui de cet
appareil ou de tout autre appareil doivent
être connectés au véhicule séparément et
avec des vis différentes. Si la vis du fil de
masse se desserre ou tombe, il peut en résulter un incendie, de la fumée ou un dysfonctionnement.
Connexions
T
01
Sans position ACC
! Utilisez cet appareil uniquement sur des véhicules avec une batterie 12 volts et une
mise à la masse du négatif. Le non respect
de cette prescription peut engendrer un incendie ou un dysfonctionnement.
! Pour éviter un court-circuit, une surchauffe
ou un dysfonctionnement, assurez-vous de
respecter les instructions suivantes.
— Déconnectez la borne négative de la batterie
avant l’installation.
— Fixez le câblage avec des serre-fils ou de la
bande adhésive. Pour protéger le câblage, enroulez dans du ruban adhésif les parties du
câblage en contact avec des pièces en métal.
— Placez les câbles à l’écart de toutes les parties mobiles, telles que le levier de vitesse et
les rails des sièges.
— Placez les câbles à l’écart de tous les endroits
chauds, par exemple les sorties de chauffage.
— Ne reliez pas le câble jaune à la batterie à travers le trou dans le compartiment moteur.
— Recouvrez tous les connecteurs de câbles qui
ne sont pas connectés avec du ruban adhésif
isolant.
— Ne raccourcissez pas les câbles.
— Ne coupez jamais l’isolation du câble d’alimentation de cet appareil pour partager l’alimentation avec d’autres appareils. La
capacité en courant du câble est limitée.
— Utilisez un fusible correspondant aux caractéristiques spécifiées.
— Ne câblez jamais le câble négatif du haut-parleur directement à la masse.
— Ne réunissez jamais ensemble les câbles négatifs de plusieurs haut-parleurs.
! Lorsque cet appareil est sous tension, les signaux de commande sont transmis via le
câble bleu/blanc. Connectez ce câble à la télécommande du système d’un amplificateur
de puissance externe ou à la borne de
commande du relais de l’antenne motorisée
du véhicule (max. 300 mA 12 V CC). Si le véhicule est équipé d’une antenne intégrée à la
lunette arrière, connectez-le à la borne d’alimentation de l’amplificateur d’antenne.
! Ne reliez jamais le câble bleu/blanc à la
borne d’alimentation d’un amplificateur de
puissance externe. De même, ne le reliez pas
à la borne d’alimentation de l’antenne motorisée. Dans le cas contraire, il peut en résulter un déchargement de la batterie ou un
dysfonctionnement.
8
9
a
b
c
d
Un adaptateur de télécommande câblée
(vendu séparément) peut être connecté.
Entrée microphone
Microphone
4m
Sortie arrière ou sortie des aigus
Sortie avant ou sortie des médiums
Sortie des extrêmes graves ou sortie des graves
Câble USB
1,5 m
! Si USB1 (périphérique de stockage USB
1)/iPod1 (iPod connecté via l’entrée USB
1) et USB2 (périphérique de stockage
USB 2)/iPod2 (iPod connecté via l’entrée
USB 2) sont connectés simultanément,
utilisez un câble USB Pioneer (CD-U50E)
en plus du câble standard USB Pioneer.
Cordon d’alimentation
1
L
R
2
4
Cet appareil
9
3
4 56
78
a b
1 Port USB 1
2 Port USB 2
3 Entrée antenne
15 cm
4 Entrée audio
5 Fusible (10 A)
6 Entrée cordon d’alimentation
7 Entrée télécommande câblée

5

R/H

6
7
8
9
a
b
c
d




e
f
g
h
i
2
1
d

F/M
3
c
1
2
3
4
Vers l’entrée cordon d’alimentation
Gauche
Droite
Haut-parleur avant ou haut-parleur de médiums
5 Haut-parleur arrière ou haut-parleur d’aigus
6 Blanc
7 Blanc/noir
CAR AUDIO SYSTEMS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement