|'

|

:

|

I

2-Year Warranty

Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship andi'or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.

Antennas may also be returned directly to the manufacturer at the consumer's expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics.

Witson Electronics shall. at its option. either repair or replace the product. Wilson Electronics will pay for deiivery of the repaired or replaced product back to the original consumer.

This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected to misuse. abuse. neglect, or mishandling that alters or damages physical or electronic properties.

RMA numbers may be obtained by contacting Technical Support at 866-294-1660.

I

I" l

[

F i

Disclaimer: The information provided by Wilson Electronics, LLC is believed to be complete and accurate. However. no responsibility is assumed by Wilson Electronics. LLC for any business or personal losses arising from its use. or for any infringements of patents or other rights of third parties that may result from its use.

1

I

’

Copyright © 2014 Wilson Electronics, LLC. All rights reserved.

Antenna Speci fi cations l

I

H339;

Frequency

Range

W l $4412 I 30445.1 .

I 304411

703300 MHz 1' 324-894 MHz! 830-960 MHz! 1710-1880 MHz

1350-1900 MHz I 2110-2100 MHz

311135 I 314473. I 31115.5 I 314453-.- | -

698-116 MHz 1‘ new? MI-izi 824649 MHz! 1710-1755

MHz! 1350-1995 11112

131115554350 ggmy fi gj mmg fi z’ i _

18501995 MHz

Impedance 50 Ohms 75 Ohms 50 Ohms 1'5 Ohms 50 ohms 50 ohms 75 Ohms l 50 Ohms 75 Ohms

Corrector

Antenna

Gain

Polarization

BeamTviai fi

Horizontal _ l

N-Fen'iaio . F-Famala

. it EEii

N-Femaie F-Femaie N-Female I N-Female F-Femaie N-Femaie ; F-Female

5'2 fl it] 1 dBi mirag fi jfj fi : 3321;251:3083?) MHZ 3.8 031633-716 MHz {3.6 dBi 776-787 MHz 1‘44 031 824-849? 778-787 MHz! 1.81 dBi 824-849

'

.

ti dBi 2110-2100 114142

.

1.49ciBi698-716MH21126d3i

I MHz {8.2 (113i 1710-1755 MHz! 10.0 081 1850-1995 MHz I MHz i 4.25 dBi 1710-1755 MHz!

5.72 dBi 1350-1995 MHz

Vertical

1'0 i 50 Deg

1ul'eriit‘al Plane

Max Power

Dimension

Weight '

_ 50 ’45 Deg

50 Watts

8.27 x 7.09 x 1.13 {inch} 121 x 18 x 4.39 {cm}

1.32 lbs 1 0.6 kg

Wilson Electronics. LLC

3301 East Deseret Drive. St. George. UT 84790

For additional Technical Support visit www.WilsonElectronics.com

or email at: [email protected]

Phone: 866-294-1660 Local: 435-673—5021 Fax: 435-656-2432 wwwtwittercom fl NiIsonCellular www.facebook.comNViIsonCelluiar

1030?4_Rev13_02.13.15

_

Wide-Band

Panel Antenna

Window, Ceiling, Wall

& Outdoor Mounts

WINDOW

#304452

#304472 cenLnus

#304451

#304471 vnALL

#311135

UPGRADE- #311155-0630

#311155

POLE

# 314453

#314473

UI

.

E

”1”” "'“T'T'” “.-

‘ ‘%

.

" '

“" 45-4/

Appearance of device and accessories may vary.

i The wide-band panel antenna is vertically polarized. For optimum

' performance. install the antenna with the cable running from the bottom or the top.

(9Wilson

Electronics

Wide-Band Panel Antenna

Window, Ceiling, Wall & Pole Mounts

Window Mount:

#304452 - 5t) Ohm

#3044T2 - ?5 Ohm

Ceiling Mount:

#304451 — 5t]| Ohm

#3044T1 - 75 Ohm

Wall Mount:

#311135

#311155

Pole Mount:

#314453

#314473

Optional ln-Wall

Mount Accessory:

;.

W

DTcG Inside Panel

Antenna Upgrade

#31 1 1 55-0630

Panel Antenna wiF-Fernale Connectors

R86 30' Coax Cable wiF—Male Connectors

Required F-Femote to SMA

Mate adapter #2Fl t65

83 ioo t

.

1

(extra parts may be included in hardware packet)

Appearance of device and accessories may vary.

a ..

.. J' ln-Wall Mounting

Bracket

(901123)

Window Mount Installation

To be used as your outside antenna which communicates with the cell tower

Find the window that faces the direction of the nearest cell tower. The signal strength function on your cell phone can help you determine this.

Call Customer Support at 866-294-1660, for instructions on accessing the signal strength function on your particular phone.

Choose an inside window location where the antenna will be hung.

Clean the window and the suction cups with glass cleaner.

It is important that the small tabs on each suction cup be facing outward so they may be used to remove the antenna from the window if desired.

Use firm and even pressure to attach the antenna to the window without breaking the glass. Avoid excessive or sudden pressure against the glass.

Refer to Signal Booster instructions for separation requirements.

' tact Wilson Electronics Customer Support Team with any questions at 866—294-1660

I I . Or email: tecn@ witsonetectronics. com Mon-Fri. Hours: 7am to 6pm MST.

Wide-Band

Panel Antenna

Slide Panel

Antenna into cradle

Remove Back Panel Before

Utilizing Other Mounting Options

Vt remove tape

Window Cradle

Mount

Panel ‘ “111%” a g...

Antenna ..

ii back panel

I

Carefully pull back panel cover away fro ' antenna until tape releases [this will take some force}. Peel off tape and .: residue before installing different m 31:. j options.

Contact Wilson Electronics CustomerSupport Team with any questions at SSS-Mt t.....ii::_.l'

Or email: tech@ wilsonelectronicscorn Mon—Fri. Hours: ?am to 6pm MST: _

Ceiling Mount Installation

Select a location on the ceiling that you can access from above to run the antenna cable. Verify that your chosen location allows for the necessary separation between the Inside and Outside Antenna

(see Signal Booster installation instructions for antenna separation requirements).

Use the antenna as your template in your predetermined location.

Note: Ensure that the cable connector location is NOT below a ceiling rafter.

A A

:1 n :r 9, drill hole in ceiling for end connector

Ceiling Mount léanohor

N "'x

0 wood screw g wood screw

I

Wide-Band Panel Antenna

Drill a hole large enough to accommodate the dimension of the connector on the location you have marked for the cable. Hold the antenna to the ceiling and mark the locations for the screws and then drill a 3/16 inch hole and tap anchors into the pre—drilled screw holes.

Remove Ceiling Mount Before

Utilizing Other Mounting Options

Attach the Signal Booster “Inside

Antenna” cable to the connector on the

Ceiling Mount Antenna. Place the antenna flush against the ceiling, and then screw the antenna into place

(screws and anchors provided). Be

Tgcareful not to over—tighten.

" if you have any questions about the

-"-"'j;_ gallation procedure, please

*‘i .. ct our Customer Support Team toll

-_;.._§66-294-1660 or email

"f"isonelectronicscom.

Panel Antem

“1 am :“‘"=-g~::m:tgiln:om

tastiest“

//

Vii,

" M a 1c:

{ $1

ll , l/__

Wall Mount Installation

Find the desired location for the Panel Antenna. Verify that the Panel

Antenna and the Outside Antenna have the necessary separation (see

Signal Booster instructions for requirements).

For optimum results, the antenna should be mounted a minimum of 6 feet from the floor.

Utilize Wall Mount Bracket (see diagram below) as your template. Drill out the four holes for the screws in the wall, using a 3/16 size drill bit, following your template. Tap in wall anchors provided and place the mounting bracket over the wall anchors, insert the screws and tighten.

Slide the Panel Antenna onto the wall mount bracket (see diagram below).

fl

Wide-Band

Panel Antenna a

-

I

_ l

_

,

I anchor &

‘7 slide into mount

/

Wall Mount

& hardware anchor & screw

(

' l

'

V l

_

I i

I v

Remove Mount Before Utilizing

Other Mounting Options xfi —Tm fifi V remove back panel

-- '"' mount from Panel

Antenna beiore utilizing other mounting options

.._,,_

"-3x drywall

H.

as

Panel Antenna H

.__‘_\_—

Contact Wilson Electronics CustomerSupport Team with any questions at 8661'

Or email: tech@wilsonelectronicscom Mon-Fri. Hours: 7am to 6pm be ck view

Pole Mount Installation

The antenna should be mounted as shown in the illustration below. The included mounting bracket is adjustable and will accommodate pipe diameters from 1.25 inches to 2 inches (pipe sold separately #901117).

Mount the antenna so that there is at least 3 feet of clearance in front and sides. Position the antenna so that it has the most unobstructed line of sight to the cellular service provider's strongest signal. If you are using a wireless Signal Booster, make sure the antenna is not pointing across your own roof.

Refer to Signal Booster instructions for separation requirements.

& Warning: Lightning protection is recommended for all installations, sold separately (Wilson Electronics #859902—50 Ohm &

#859992—75 Ohm). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines.

Postion for strongest signal

O

0

Ii)

0

'tl‘;|"“-:@3

@ _____?0 @-"—-II[]:--'(

‘3

,3

@ hi

' "

\

@

.'

Q .

fl .

Pole Mount

& hardware pipe sold separately

#901117

.

tact lMtSDn Electronics Customer Support Team with any questions at 866-294-1660 or email: [email protected]

Mon-Fri. Hours: 7am to 6pm MST.

Adjusting the Antenna for Maximum Performance

To adjust the antenna for best performance, connect it to your cell phone with an External Adapter and a length of cable (External Antenna

Adapters and cables are sold separately). Put the cell phone in test mode and turn the antenna in 10-degree increments while checking the cell phone’s signal level. At each point you may need to wait a few seconds as your cell phone updates.

Eh

Cell Tower

RF Signal \

1—-

‘ EEK

‘ l

Wide fl and

Antenna

EXCELLENT

Signal Strength

GOOD

Signal Strength

POOR

Signal Strength

NO

SIGNAL

L

Hal l

‘13 ~50dB

I

~60dB

I

—70dB l sods l sous

| I mods mods J

Signal readings usually appear as a negative number (for example, -86).

The larger the number, the more powerful the signal (-75 is stronger than

-84). See graph above.

Once you have obtained the strongest signal, fully tighten the mounting hardware. After the Signal Booster and the rest of the system is installed and performing correctly, weatherproof all connections.

Important: If you are using a Wireless Signal Booster, be sure the antenna is not pointing across the building in which you are trying to get coverage. The antenna should point away from the building to help prevent oscillation (feedback).

Ultra low loss cable is recommended for lengths 20 feet or greater to prevent significant signal loss. Wilson Electronics offers WILSON 400 cable in several lengths from 20-100 feet Wilson Electronics also offers a wide range of phone adapters to connect your cell phone to a Signal

Booster or directly to the antenna. To find the adapter for your phone, or . '_. f?

call toll free 866-294-1660.

Contact Wilson Electronics CustomerSupport Team with any questions at 866-294-166Q

Or email: [email protected] Mon-Fri. Hours: 7am to 6pm MST