THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION. PLEASE
READ AND KEEP FOR FUTURE REFERENCE.
Lot Number:
Date:
Item No: 63607147
MIN :
2.95in
/75MM
MAX:
15.75in
Congratulations on your Catalyst purchase. Follow these simple instructions and you’ll have your TV mounted in no time.
This kit fits most TVs 12in. - 42in. (30cm - 107cm), up to 55lbs (25kgs).
Keep this Instruction Manual for future reference.
Keep your original proof of purchase (store receipt).
If you have any questions and/or wish to order parts, please call us toll free at 800-747-2660.
Before Proceeding any further please make sure your kit has the following items.
1 x Heavy Duty Low Profile Fixed Mount
2 x 8.66in. (220mm) Velcro Cable Ties
1 x 6 ft. HDMI ™ cable
Tools Needed ( Not Included)
Safety Glasses
Wood
Drill Bit 5/32in.
(4mm)
Masonry/Concrete
Drill Bit 3/8in.
(9,5-10mm)
Philips
Screwdriver
Hammer
Masonry/
Concrete
Wall Anchor
1
Drill
Stud
Finder
Parts List
Item Components
Wall Plate
A
TV Bracket
B
Qty Item
1 C
Components
Lag Bolt
Magnetic Leveler
2 D
Qty
2
1
Hardware List
Mounting Hardware List Qty
J
K
I
L
M8 X 16MM
M6 X 12MM
M5 X 12 MM
M4 X 12MM
4
4
4
4
M
N
M8 X 40 MM
M6 X 35MM
4
4
O
P
Q
R
Mounting Hardware List Qty
4 M5 X 30MM
M4 X 30MM
M4 / M5washer
4
4
M6 / M8washer 4
S 4
T
M6 / M8spacer
M4 / M5spacer 4
2
Assembly Tips:
Become familiar with the instructions and all parts.
Make sure that all parts are in the box and in good condition.
Assemble the product on the open flat carton or a rug to protect the product and your floor.
Some heavy products need a second person to assist in the assembly.
Do not install on sloping surface.
This TV mount is designed for use on a vertical wall that is constructed with wood studs, masonry or solid concrete.
Never let children climb on product or play with product.
Do not sit or stand on product.
Do not fasten a TV that is heavier than the recommended loading to the mount.
Improper installation may cause property damage and or personal injury, so the installation is recommended to be done by two qualified contractors. The manufacturer is not liable for damage or injury caused by incorrect mounting, assembly or use.
The size and weight of your TV must be not exceed 12in. - 42in. (30cm - 107cm) diagonally or 55lbs (25kgs). The wall must be capable of supporting five times the weight of TV plus the mount.
Improper handling can result in cuts and lacerations.
Pictures for reference only, subject to our available products.
3
1
Wall Stud Installation
16in. /407mm
C
A
Using a stud finder, locate the center of wall studs, then hold wall plate (A) against the wall at your desired position. Next use a pen or pencil to mark the location of where the 2 mounting Lag Bolts (C) will go into the center of the wall stud. Before marking, ensure the wall plate is level using the included magnetic leveler (D).
Remove wall plate. Drill pilot holes at the marked 2 holes using 5/32 in. (4mm) drill bit.
Fasten wall plate (A) to wall with Lag Bolts (C).
Do not over-tighten Lag Bolts (C).
This unit is designed for 16in. (407mm) spaced wood studs.
Masonry/Concrete Installation
Wall Anchor
(Not Included)
C
A
Use a pen or pencil to mark the location of where the 2 mounting Lag Bolts (C) will go into wall while holding Wall Plate (A) against the wall at your desired position. Before marking, ensure the wall plate is level using the included magnetic leveler (D).
Remove wall plate. Drill holes at the marked 2 holes using 3/8 in. (9,5-10mm) drill bit. Sink Lag
Bolt Anchors (not included) into holes with hammer until flush with wall surface. Fasten Wall
Plate (A) to wall with Lag Bolts(C).
Do not over-tighten Lag Bolts (C).
4
2
Spacer S or T
B
B
Carefully lay your TV face-down on a rug or flattened carton. Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M4, M5, M6, or M8) to use.
If your TV has a flat back, use the shorter screws. Spacers and longer screws are supplied to accommodate:
Irregular / round back TVs
TVs with inset mounting holes
Extra space is needed to access cable connections
Position your TV brackets (B) over your TV hole pattern, making sure the brackets are vertically centered and level. Install using the short screw or long screw with spacer combination you selected for your TV.
DO NOT TIGHTEN SCREWS WITH ELECTRIIC DRILL/SCREWDRIVER. HAND TIGHTEN ONLY.
3 safety screws
Hang TV to wall plate as shown above. It is recommended two people, one on each side of
TV participate in hanging TV to wall plate.
Tilt the top of the TV towards the wall and carefully position TV brackets (B) over the wall plate (A) until both sides lock into place. Then tighten safety screws.
5
HDMI Cables
Information:
This Kit includes 1 HDMI™ cable.
Each HDMI cable measures 6 feet (1829 mm) in length.
Technical Specifications:
1.4 Version
Supports Ethernet, 3D and 4K Definition.
O.D.: 6.0mm
Double molding
In-Wall CL2 Rated
Velcro Cables Ties
Information:
This kit includes 2 velcro cable ties to help manage your cords.
Each Velcro cable tie measures 8.66in. (220mm)
Product Warranty
This Limited Warranty covers any defects in material or workmanship for purchases made in the
U.S.A and Canada, and excludes claims from conditions, malfunctions or damage not resulting from defects in material or workmanship. The warranty duration is one year. Keep your original proof of purchase (store receipt). If after inspection you find the product is defective, damaged or missing parts. DO NOT return to the store. Please contact customer service at (800) 747-2660 M-Th, 8am-5pm; Fri, 8am-12pm (Pacific Time).
Or email [email protected]
Please keep this Instruction Manual for future reference.
2015
U.S. and other foreign patents pending /
Patentes de los EUA y países extranjeros en trámite /
Brevets en cours pour les États-Unis et autres pays /
U.S. und andere ausländische Patente sind hängig
All rights reserved / Derechos Reservados /
Tous droits réservés
Made in China / Hecho en China /
Fabriqué en Chine
6