NETUM 8541732582 Bar Code Scanner User Manual

NT-1228BL V18.7.12

Quick Setup Guide

This model can work both via USB cable or via bluetooth.

Connection Mode

Working via USB cable

Get Started : Connect scanner with your device via USB cable. If you use US keyboard, it's a plug and play model. If you use other type of keyboard , please refer to below "keyboard language type" to set the keyboard language before use it.

Working via Bluetooth

Get Started : After you connect the bluetooth with your device (please refer to the section of "bluetooth connection" from this manual) then you can start to use it. (US keyboard by default) If you use other type of keyboard , please refer to below "keyboard language type" to set the keyboard language before use it.

Low voltage Alarm : Scanner will make 2x beeps to remind you that it's under low voltage. Plug the USB cable to charge power for it.

Important Notes: In case scanner has run out of battery during the storage, please charge power for 2-3 hours on the first time when you use it.

If you want to have other configurations please refer to below programming barcodes.

Barcode Programming

Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.

Bluetooth Connection

1.

Pairing with windows XP or Windows 7/8/10

1)

2)

3)

Power on the scanner , a few seconds later the blue indicator will keep flashing.

Enter the ‘Control Panel’ - ‘Devices and Printers’ - ‘Add a device’ – select, ‘Bluetooth’ to add the device to your computer

Click ‘Next’, the scanner will beep to indicate a successful pairing, and the light will turn to solid blue.

2.

Android: Connect Android Device in Basic Mode

1)

2)

Power on the scanner. Make sure the scanner is discoverable (unpaired). a few seconds later the blue indicator will keep flashing.

Touch Home | Menu | Settings | Wireless & Networks | Bluetooth settings

3)

4)

5)

6)

Make sure the device has Bluetooth “On”. Scan for devices.

In the list of found devices, select “Netum Bluetooth”. Tap Pair.

The scanner will connect to the Android device.

The scanner will beep once after it has connected and is ready to scan barcodes

3.

Pairing with your IOS device

1) Power on the scanner. Make sure the scanner is discoverable (unpaired). a few seconds later the blue indicator will keep flashing.

2)

3)

Click on “Bluetooth” in the left column. Your IOS device will automatically start searching for any

Bluetooth Devices in the area.

Once you have identified the “Netum Bluetooth” on the screen, tap on it and you will automatically be connected. The scanner’s LED light will turn to solid blue.

Operation mode

A) BT HID Mode (Default)*

No Software installation needed, connects to most devices with bluetooth or USB interface. In this mode, the scanner interacts with the device like a keyboard. Therefore, the scanner will work with Safari, Notes, and any other applications that supports an active cursor.

BT HID Mode

Note: this command barcode is only apply for Bluetooth Wireless Mode

Keyboard Language

In order to let scanner upload the codes in a correct way, you have to set the keyboard language before you use it.

For example

If you use French Keyboard, just scan barcode of "French Keyboard", after that scanner will upload barcodes according to French keyboard layout. American Keyboard is set by default, if you use a US keyboard you can just skip this part.

American Keyboard * Portugal Keyboard

French Keyboard Spanish Keyboard

Germany Keyboard Turkey Q Keyboard

Italy Keyboard Turkey F Keyboard

B) Application Mode (SPP)

For Android or Windows only

Software installation is required, If you have an application that supports mobile scanners this is the mode recommended.

BT SPP Mode

Note: this command is only apply for Bluetooth Wireless Mode

Scan Mode

Trigger Mode (Default)

Scanning this bar code will enable the scanner to enter manual trigger mode.

Continuous Mode

This mode enables the engine to scan/capture, decode and transmit over and over again.

Auto Sense Mode

Scanning this bar code will enable the scanner to enter auto sense mode.

Working Mode

If you are heading for a working area which lies outside the signal range, you may activate the offline mode of the scanner, following the steps described below. Under this enhanced offline mode, all scanned data will be stored directly into the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them time and again to your liking.

1). By scanning the following barcode, the offline mode will be activated

Offline Mode

2). By scanning the following barcode, all data in the buffer memory will be deleted

Clear Memory

3).By scanning the following barcode, all data entries in the buffer memory can be manually uploaded after reconnecting to the working station (only in offline mode).

Uploading the Data

4). By scanning the following barcode, the gross quantity of the uploaded data entries will be summarised

(only in offline mode).

Summarising of uploaded data entry quantity

5). By scanning the following barcode, the device leaves the offline mode, instant uploading mode will be activated. (By default)

Instant uploading mode

Notes: Command barcodes from Working mode section are only applied for Bluetooth wireless mode,

Terminator

The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below.

None CR&LF *

CR TAB

Idle Time

Scanner will stay awake during the idle time that you set for it and turn to sleep if you haven't used it during the whole idle time.

30 s 6 Mins

12 Mins 30 Mins

1Hour 2Hours

IOS Keyboard POP UP/HIDE

During the scanning IOS keyboard can be hided or popped up by scanning below command barcode.

Restore factory default

Scanning the following barcodes one by one to restore the scanner to factory defaults. (Four steps included)

1. Factory Restore

2. Serial Port

3. Baud Rate 19200

4. Enter+LF

Common function Barcodes Enable/Disable UPC-E

1000021

*Enable UPC-E

Enable/Disable EAN-8

1000020

Disable UPC-E

1000041

*Enable EAN-8

Enable/Disable EAN-13

1000040

Disable EAN-8

1000031

*Enable EAN-13

Enable/Disable Bookland EAN(ISBN)

1000030

Disable EAN-13

1000231

Enable Bookland EAN

Decode UPC/EAN Supplementals UPC/EAN

1000230

*Disable Bookland EAN

Supplementals are bar codes appended according to specific format conventions (e.g.UPC

A+2, UPC E+2, EAN 13+2, EAN 13+5). The following options are available:

• Do not read supplementals – The scan engine can only read the barcode no matter the barcode with supplementals or not.

2010E00

*Ignore UPC/EAN with Supplementals

• Only read the barcode with supplementals- The scan engine can only read the barcode with supplementals.

2010E01

Decode UPC/EAN with Supplementals

• Auto read supplementals- The scan engine can not only read the barcode with supplementals,but also read the barcode without supplementals.

Eable/Disable Code 128

2010E02

Auto discriminate UPC/EAN Supplementals

1000101

*Enable Code 128

Enable/Disable Code 39

1000100

Disable Code 128

1000001

*Enable Code 39

Enable/Disable Code 39 Full ASCII

1000000

Disable Code 39

1020111

Enable Code 39 Full ASCII

1020110

*Disable Code 39 Full ASCII

NOTE Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If you get an error beep when enabling Code 39 Full ASCII, disable Trioptic Code 39 and try again.

Enable/Disable Code 93

1000111

Enable Code 93

Enable/Disable Code 11

1000121

Enable Code 11

Enable/Disable Interleaved 2 of 5

1000061

*Enable Interleaved 2 of 5

Enable/Disable Matrix 25

3030201

Enable Matrix 25

Enable/Disable Codabar

1000071

Enable Codabar

1000141

Enable MSI

1000110

*Disable Code 93

1000120

* Disable Code 11

1000060

Disable Interleaved 2 of 5

3030200

*Disable Matrix 25

1000070

Disable Codabar *

1000140

*Disable MSI

Enable/Disable GS1 DataBar-14

1000351

Enable GS1 DataBar-14

Enable/Disable GS1 DataBar Limited

1000350

*Disable GS1 DataBar-14

1000361

Enable GS1 DataBar Limited

Enable/Disable GS1 DataBar Expanded

1000371

Enable GS1 DataBar Expanded

Enable/Disable PDF417

1000360

*Disable GS1 DataBar Limited

1000360

*Disable GS1 DataBar Limited

1000370

*Disable GS1 DataBar Expanded

1000170

Disable PDF417

Enable/Disable QR

1003250

Disable QRCode

Enable/Disable Data Matrix(DM)

1003240

Disable DataMatrix

1000171

*Enable PDF417

1003251

*Enable QRCode

1003241

*Enable DataMatrix

Support

For any inquiries concerning our products, please send an email to [email protected], and we will respond to you as soon as possible.

Contact Information

Tel.:+0086 20-6626-0708

Email:[email protected]

Addr.:Unit 137, The Pacific Industry Park, Xintang Town,Zengcheng District, Guangzhou,China/511340

Made in China