SCHLAGE BE469NXCAM619 Deadbolt Quick Start Guide

Quick Start Guide

Backplate

Backup Key

Touchscreen

Assembly

Parts

Strike

Bolt

Reinforcement

Screws

Inside Assembly

Screw

Battery

Cover

Inside

Assembly

Thumbturn

Backplate

Screws

Bolt/Strike

Screws

Reinforcement

Plate

Set Screw

Interactive experience

For an improved installation experience, follow the link below or scan the QR code for online interactive instructions, warranty, and reference information.

https://instructions.allegion.

com/instr/86/2110

Tools

1

4 5

2

3

Phillips screwdriver

Don’t use a power drill!

Support

U.S.A.: 888-805-9837

Canada: 800-900-4734

Mexico: 018005067866

step

1 Need Help?

See “Help with Step 1” in the online instructions. The link is on the back cover or the third page of this guide.

Install the bolt.

You may have to adjust your bolt length. Make sure the slot in the bolt is centered in the hole.

Make sure the word “ TOP ” is facing up.

Twist the faceplate to extend.

Slot is centered in the hole.

No change needed.

Keep twisting until 2 ¾”.

Actual Size

step

2

Need Help?

Trouble installing the strike reinforcer? See

“Help with Step 2” in online instructions.

Install the strike into the door frame.

If you have a window next to your door, you may not be able to use the longer wood screws to install the reinforcer.

Install this strike reinforcer for enhanced security.

Actual Size

Actual Size

step

3

Is it hard to install the touchscreen?

Is the tailpiece not installing correctly?

If the hole through your door seems too small, you may need to remove the spacer. See the online instructions.

Install the touchscreen.

Route the cable through the door BELOW the bolt. Align the tailpiece as shown and push the touchscreen onto the door.

The bump on the tailpiece aligns with the slot in the bolt.

step

4

4 5

3

2 1 Phillips screwdriver

Don’t use a power drill!

You may damage your lock!

Install the inside backplate.

Route the cable below the bolt and through the hole on the bottom of the backplate. Secure the backplate with screws.

TOP

Make sure that “TOP” is facing out.

Actual Size (2)

Hold the touchscreen on the outside of the door while you tighten the screws.

Phillips screwdriver step

5

Take off the battery cover.

step

6

Connect the cable.

The connector fits only one way.

step

7

Secure the lock to the door.

If the bump on the tailpiece doesn’t align with the slot in the back of the inside assembly, make sure your thumbturn is vertical

(up and down). Tuck the wire into the channel.

Tuck wire.

Align bump on tailpiece with notch.

step

8

4 5

3

2 1

Install the screws.

Install the lower screw first.

Phillips screwdriver

Don’t use a power drill!

You may damage your lock!

2 nd

Actual Size

1 st

Actual Size

Phillips screwdriver step

9

Install batteries and slide the cover on.

-

+

-

+

-

+

-

+

step

10

Set up your lock.

1. Open your door!

2. Enter one of the two default user codes.

The codes are located on the back of this guide and on the back of the inside assembly. You need to remove the inside assembly to see the label.

3. Your lock will enter a setup routine.

When the bolt stops moving, setup is complete.

step

11

Need Help?

If the bolt doesn’t extend or retract during testing, see the online instructions and make sure spindle is aligned properly.

Test your lock.

1. Close your door.

2. Extend and retract the bolt using the inside thumbturn.

3. Make sure the bolt retracts smoothly. If it doesn’t your door and frame may not be aligned.

4. Open your door.

5. Extend the bolt using the inside thumbturn.

6. Now enter a user code at the touchscreen to check that the bolt retracts.

step

12

Enroll your lock.

1. Place your smart home system or panel into enrollment mode (see documentation for that device for details).

2. Remove the battery cover.

3. Press then release button.

4. A yellow flashing light indicates enrollment is in progress.

5. A solid green light indicates successful enrollment.

L A red light indicates an enrollment issue, try repeating steps 1-3.

Lock and unlock

To lock your door just tap the logo.

You can also lock your door by entering a user code while the door is closed or by turning the thumbturn toward the door edge.

To unlock your door enter a user code.

You can also unlock your door from inside by turning the thumbturn away from the door edge.

Add and delete codes

1

Press

2

Enter

Programming

Code

(6 digits)

• The lock supports user codes between 4 and 8 digits and is set to a default length of 4 digits.

• The first 4 - 6 digits must be different from the first 4 - 6 digits of the programming code.

3

Choose and press: add or delete

4

Enter the user code you’d like to add or delete.

5

Enter that code again.

indicates success add or delete another user code

Factory defau

l

t reset

If you have forgotten your programming code, you can restore the default codes. If you want to move the lock to a different door, you need to restore default settings. Move the lock to the new door, and then set it up again.

1. Disconnect

your batteries.

2. Press and hold

down the

logo.

While you are pushing

the logo, reconnect

your batteries.

3. Test your lock

with one of your

default codes,

located on the

back of this

guide.

Now set up your lock, see: step

10

Save this guide!

PLACE LABEL

HERE

PLACE LABEL

HERE

© Allegion 2018

Printed in U.S.A.

P518-669 Rev. 06/18-b

Access step-by-step instructions and help.

https://instructions.

allegion.com/ instr/86/2110

*P518-669*

P518-669