Whynter ARC-110WD Portable User Manual

Whynter ARC-110WD Portable User Manual
WHYNTER 11,000 BTU DUAL HOSE PORTABLE AIR CONDITIONER
co
MODEL# : ARC-110WD
Instruction Manual
Congratulations on your new WHYNTER product. To ensure proper operation, please read this Instruction
Manual carefully before using this product. Keep this manual in a safe place for future reference.
TABLE OF CONTENTS
INTRODUCTION
3
SAFETY PRECAUTIONS
4-5
IDENTIFICATION OF ACCESSORIES
6
IDENTIFICATION OF PARTS
7
INSTALLATION INSTRUCTIONS
8-9
AIR FILTERS INSTALLATION
10
REMOTE CONTROL
11
OPERATION INSTRUCTIONS
11-14
WATER DRAINAGE
15
CARE AND MAINTENANCE
16
TECHNICAL DATA
17
TROUBLESHOOTING
18-19
WARRANTY INFORMATION
20
2|Page
Thank you for choosing the Whynter portable air conditioner. Please follow the instructions provided
in this user guide to obtain the very best performance from your portable air conditioner and take full
advantage of the many features your portable air conditioner offers you. We trust that your Whynter
air conditioner will provide the performance and reliability that we stand for.
Please keep this user manual in a safe place for future reference.
DISPOSAL
This symbol on the product or its packaging indicates that the appliance cannot be treated as normal
domestic trash, but must be handed in at a collection point for recycling electric and electronic
appliances. Your contribution to the correct disposal of this product protects the environment. Further
information about the recycling of this product can be obtained from your local municipal authority.
3|Page
Your safety and the safety of others are very important to us.
To reduce the risk of fire, electrical shock or injury when using your appliance, follow these basic precautions.
SAFETY PRECAUTIONS
Before the portable air conditioner is used, it must be properly positioned and installed
as detailed in this manual.




















Do not under any circumstances cut or remove the third (ground) prong from the power
cord.
Make sure this unit is connected to a correctly grounded power supply outlet. Do not use an
extension cord or power strip.
The power cord is UL listed. It has a built-in L.C.D.I. (leakage, current, detection,
interruption) circuit breaker for added safety. If the power supply is interrupted, press the
reset button to reconnect the unit to power source.
It is recommended to use a separate circuit that its size should be 15 Amps for the air
conditioner.
Do not use an excessively wet cloth, industrial solvents, oil-based products to clean this
portable air conditioner.
To avoid the risk of shock, the product should never be used in bathrooms, shower rooms,
or in any other steamy or wet areas.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliances.
Do not repair, disassemble and/or modify the unit by yourself.
Always turn off the portable air conditioner when cleaning the air filter, and transporting.
Do not turn this unit on and off by plugging and unplugging. Always use the ON/OFF switch.
Transport the unit in an upright position only, or leave it in an upright position for a minimum
of 4 hours before first use.
Ensure curtains or other objects are not obstructing the air inlet filters.
Do not bend or crush the exhaust hose while in use.
Always allow at least 20” of clearance around the unit for ventilation. Do not use this unit
inside closets, cabinets and/or cramped spaces between furniture.
This unit is optimized to operate in an ambient temperature of 64°F – 95°F.
This unit must be installed in an area protected from the elements, such as wind, rain,
water spray or drips.
The unit should not be placed next to ovens, grills or other heat sources.
Always place the unit on even and hard and level surface.
Do not sit or place objects on the unit.
Do not allow children to climb, stand or hang on the unit. The air conditioner could tip over
and get damaged and/or seriously injure somebody.
4|Page









Keep fingers out of the air intakes and air outlets.
The unit is an electrical appliance. To avoid injury from electrical shock do not operate it with
wet hands, while standing on a wet surface or while standing in water. Do not use it in
outdoors or in wet conditions.
When positioning or moving the unit, ensure it is not turned upside down or greater than 45°
or more off level.
This unit is designed for household, non-commercial use only. Any other use will void the
warranty.
Do not plug into the power outlet before set up is completed.
Do not operate this unit without the air filter(s).
Do not use harsh chemicals to clean the filter(s). Dry thoroughly before inserting the filter(s)
into the unit.
Do not add extra length to the exhaust hose by more than a total length of 9’. This will
reduce the cooling efficiency of the portable air conditioner.
At the end of each season, all water must be drained from the unit and filter(s) must be
cleaned before storage.
THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY IF THE ABOVE INSTRUCTIONS
ARE NOT FOLLOWED.
OPERATING CONDITION
MODE
ROOM TEMPERATURE
DRY
Higher than 60°F
COOL
Higher than 66°F
Your portable air conditioner is supplied with a Leakage-Current
Detection and Interruption (LCDI) plug. This plug reduces the risk of
fire due to arcing faults in the power supply cord. Please follow the
instructions below to ensure that LCDI plug works properly.
1. Plug the power cord to a grounded wall outlet. Do not plug to
a power strip or extension cord.
2. Press the TEST button on the plug. This should trip the plug
and cut the power to the air conditioner. If the plug does not
trip and the unit comes on, please contact technical support.
3. Press the RESET button to start the air conditioner.
4. Do NOT use the TEST and RESET buttons to turn the air
conditioner on and off.
5|Page
IDENTIFICATION OF ACCESSORIES
IMAGE
ACCESSORY NAME
QUANTITY
Exhaust hose (large)
1 piece
Intake hose (small)
1 piece
Fixture
2 pieces
Screws
8 pieces
1 Large Exhaust Hose Connector to Window
Kit with tab cut-outs
1 piece
1 Large Slide Locking Exhaust Hose
Connector to unit
1 piece
1 Small Slide Locking Intake Hose
Connector to unit
1 piece
1 Small Intake Hose Connector to Window
Kit with tab cut-outs
1 piece
Window Slider Kit
1 set
Cover
2 pieces
Remote control
1 piece
Storage Cover
1 piece
Carbon Filter
1 piece
Optional Intake filter (sold separately)
• Note: Please contact us at [email protected] or visit
whynter.com for optional accessories information
6|Page
1 piece
IDENTIFICATION OF PARTS
Front
1.
Remote control
2.
Front display
3.
Air outlet
4.
Handle
5.
Wheels
Rear
6.
Air filter
7.
Air intake (evaporator)
8.
Air exhaust - large hose
9.
Air intake (condenser) - small hose
10. Power cord
11. Upper drain port (rubber plug and cover)
12. Lower drain port (rubber plug and cover)
7|Page
INSTALLATION INSTRUCTIONS
Location
The air conditioner should be placed on a hard and level surface strong enough to support its weight. The
unit is equipped with caster wheels for portability. It should only be rolled on smooth, flat surfaces. Use
caution when rolling on carpet surfaces. Do not attempt to roll the unit over objects.
The air inlet and outlet should be free of any obstructions and be placed with at least 20” of clearance for
efficient air-conditioning and circulation.
Exhaust hose Installation
When using the air conditioner, the hot air from the exhaust hose must be exhausted out of the room to
complete the air exchange of the condenser. The intake hose is optional. When the unit is operating in
dehumidifying or fan-only mode, installation of the exhaust hose is optional.
1.
Expand each end of the exhaust (large) and intake (small)
hoses about 6”.
2.
Install the Large Exhaust Slide Locking Hose Connector to
one end of the exhaust hose (large hose) and the Large Exhaust
Hose Connector with tab cut-outs to the other end of the exhaust
hose (large hose) by turning clockwise.
3.
Install the Small Intake Slide Locking Hose Connector to
one end of the intake hose (small hose) and the Small Intake Hose
Connector with tab cut-outs to the other end of the intake hose
(small hose) by turning clockwise.
4.
Slide each of the slide locking hose connectors onto the
rear of the unit (See illustration)
Only extend the hose to the necessary length, keeping it as short
and as straight as possible. We do not recommend extending the
hose more than 9' long. If you are interested in purchasing an
additional 5’ exhaust hose, please contact [email protected]
for retail sales information or visit whynter.com for a list of optional
accessories.
Note: To remove the hose(s) from the unit, press the release
button and slide the hose and connector out.
8|Page
Window kit Installation
Your window kit has been designed to fit most standard vertical and horizontal windows.
However, it may be necessary for you to modify the installation procedures for your window.
NOTE:
If your window opening is smaller than the minimum length of the window slider kit, the window
slider kit can be cut to fit the window opening. Never cut into the exhaust and intake hose cutouts on the window slider kit.
If your window opening is larger than the maximum length of the window slider kit, additional
material will be needed to cover the open space such as, Plexiglas, PVC plastic, ply wood, etc.
Alternately, an additional window slider kit can be purchased to be used in combination with the
included kit.
When using the window slider kit on a window or sliding door, additional security measures may
be needed.
1. Open the window approximately 5”.
2. Adjust the length of the window slider to the same length
and width of the opening of the window. Cut the window slider if
necessary to fit the length of your window.
3. Insert the fixture through the back grooved side of the
window slider hose cut-out. Line up the fixture with the 4 screw
holes and tighten the fixture with 4 screws from the front side of
the slider panel. (Fig. 1)
4. Fit the window slider kit into the window opening and close
the window to secure the window slider kit. For long term
installation, you may screw the window kit into your window
frame.
5. Move the air conditioner close to the window, extend the
hoses to the necessary length, keeping them as short and as
straight as possible and attach the other end of each hose to
the window slider kit.
6. Align the tab cut-outs of the hose connectors to the tabs on
the fixtures and snap the hose connectors to the window slider
kit.
9|Page
Figure 1
AIR FILTERS INSTALLATION
Your Whynter portable air conditioner is equipped with a washable Pre-Filter and an activated
carbon filter.
The washable Pre-Filter removes large particles such as dust, pet hair and dander.
The activated carbon filter is designed to remove smoke and other odor. It is recommended to
replace the activated carbon filter every 2-3 months. Follow the steps below to install the filters.
WARNING: NEVER OPERATE THE AIR CONDITIONER WITHOUT THE PRE-FILTER
1. Pull up the pre-filter frame and remove from the unit.
2. Place the activated carbon filter on the pre-filter frame by inserting it through the three
pins.
3. Once the activated carbon filter is secured, insert the assembled filter frame into the unit.
10 | P a g e
OPERATION INSTRUCTIONS
Before you begin, thoroughly familiarize yourself with the control panel of the remote control.
Follow the symbol for the desired function. The functions of the unit can be controlled by the
remote control only. When using the remote control, make sure the reception of the signal is
confirmed by a beep.
NOTE:
 Other appliances in the same room controlled by a remote control (TV, radio, stereo, etc.),
may cause interferences.
 Electronic and fluorescent lamps may interfere with the signal transmissions between the
remote control and the air conditioner.
 Remove the batteries if the remote control is not used for long periods.
REMOTE CONTROL PANEL
Timer / Temperature Set Control
Power Control
Turns the unit on and off.
The set temperature can be set between 61°F (16 °C)
and 89°F (32°C) by pressing the
and
buttons in
cooling mode only.
Clock
Fan Speed Control
Controls the 4 fan speeds: Auto, High, Medium & Low.
NOTE: Unit does not need to be vented in Fan mode.
Timer
Mode Control
Controls the 4 function modes: COOL
, FAN ONLY
Sets the current time.
and AUTOMATIC
, DEHUMIDIFY Turns the timer function on and off.
.
Fahrenheit / Celsius Selector
Changes the display temperature from Fahrenheit to
Celsius and vice versa.
11 | P a g e
FRONT PANEL
SWITCHING ON/OFF THE AIR CONDITIONER
 The unit can be switched ON or OFF by pressing the Emergency on/off switch button
on
the front display panel or the remote control.
NOTE: The functions of the portable air conditioner can be switched on by the remote
control ONLY. Without using the remote control, the unit can only be switched on at the
previous setting and turn off the unit.
LED LAMPS ON/OFF SWITCH
 Press the LED lamps on/off switch to turn on and off the LED lamps indicators.
WARNING LIGHT
 When the internal water reservoir is full, the red light will flash and the unit will stop. Remove
the drain plug to drain out the water and the unit will restart at the previous setting.
 BEFORE USING YOUR PORTABLE AIR CONDITIONER
 Remove the exterior and interior packaging
 Before connecting the appliance to a power source and operating, let the unit stand upright
for a minimum of 4 hours. This will reduce the possibility of a malfunction in the cooling
system from handling during transportation
COOLING MODE
 In this mode, the air conditioner cools and dehumidifies the room. To activate this function


mode, press the Mode Control button until the
indicator comes on. When the cooling
mode is set, the blue light on the front panel comes on and the compressor will start in
approximately 3 minutes.
NOTE: In cooling mode, hot air is exhausted from the outdoor exhaust port and the exhaust
hose must be connected to exhaust out the hot air.
The temperature setting range of this air conditioner is from 61°F to 89°F. To set the
temperature, press the
aor
buttons. This air conditioner has a 5°F temperature
cushion which if the set temperature is within 5°F of the ambient temperature, the unit runs
on fan only mode. This saves energy and prolongs the life of the compressor of the air
conditioner. Once the set temperature is achieved, the fan runs continuously.
To set the fan speed, press the Fan Speed button. In cooling mode, the difference in
noise level between the fan speeds is not very noticeable when the compressor is on.
Try setting the unit to Fan only mode, you should be able to hear the difference between
high and low fan speed settings.
12 | P a g e
DEHUMIDIFYING MODE
 In this mode, the air conditioner only dehumidifies the room, the compressor will activate
intermittently depending on the ambient temperature. To activate this function mode, press
the Mode Control button until the
indicator comes on. When the dehumidifying mode is
set, the orange light on the front panel comes on.
 Please note that when switching function mode, there will be an approximately 3 minute
transition time. In dehumidifying mode, the exhaust hose does not need to be vented. If the
exhaust hose is vented, the room will be cooled as it dehumidifies. To prevent cooling,
remove the exhaust hose from the window kit and allow the warm air from the rear to be recirculated into the room. If room temperature is higher than 77°F, the fan speed can be
adjusted. If room temperature is lower than 77°F, the fan speed is set at Low.
NOTE: When using dehumidifying mode, venting the exhaust hose to the outside is not
required. If vented, the warm air is exhausted to the outside and cooling within the room may
occur. Additionally, if the exhaust hose is not vented, the unit may require more frequent
draining. The air conditioner does not have a humidistat in which a specific humidity level
can be set.
FAN ONLY MODE
 In this mode, only the fan of the air conditioner runs and circulates the air in the room. To
activate this function mode, press the Mode Control button until the
indicator comes on.
When the fan only mode is set, the green light on the front panel comes on.
 In this function mode, the temperature cannot be set. Subsequently, set the desired fan
speed by pressing the Fan Speed button. Fan Only mode requires that the exhaust hose be
removed.
NOTE: The unit does not require venting in Fan Only mode.
AUTOMATIC MODE
 When you set the air conditioner in AUTOMATIC mode, it will automatically select cooling or
fan only operation between 77 - 85F depending on the ambient temperature. The fan speed
is automatically selected and cannot be changed and the temperature cannot be set.

To activate this function mode, press the Mode Control button until the
indicator comes
on. When the automatic mode is set, the light on the front panel displays the color of the
mode that the unit is currently operating in.
NOTE: In Automatic mode, hot air is exhausted from the outdoor exhaust port and the
exhaust hose must be connected to exhaust out the hot air.
FAN SPEED CONTROL

To set the fan speed, press the fan speed control
Automatic, High, Medium and Low.
button. Fan speed can be set at
CLOCK
for 3 seconds. Press the up or down
 To set the clock, press and hold the clock button
buttons to set the current time. To save the current time, press and hold the clock button
again for 3 seconds.
TIMER (DELAYED SWITCH ON / OFF) FUNCTION
 This function mode enables a delayed switch ON or delayed switch OFF of the air
conditioner. The time (hours) delay can be set, enabled and disabled. The timer is
adjustable between 1-24 hours.
13 | P a g e
SETTING SWITCH OFF TIMER
With the air conditioner operating in any function mode, press the Timer Control button
.
Then the
and the two digits timer indicator will come on. Set the desired time delay OFF
hours (1 – 24 hours) by pressing the up or down buttons. When the delay time set has elapsed,
the air conditioner will switch off.
To cancel the switch off timer, press the Timer Control button
and set the hour to 00.
SETTING DELAYED SWITCH ON TIMER
When the air conditioner is off, press the Timer Control button
. Then the
and the two
digits timer indicator will come on. Set the desired time delay ON hours (1 – 24 hours) by
pressing the up or down buttons. When the delay time set has elapsed, the air conditioner will
switch on in the previous setting.
To cancel the switch on timer, press the Timer Control button
and set the hour to 00.
AUTO RESTART
In the event of a power outage, the air conditioner restarts at the previously set function mode
and settings when power is restored.
NOISE LEVEL
Portable air conditioners may make sounds that are not familiar to you. The sounds listed below
are normal. Noise reflecting off hard surfaces such as a floor or wall can make the sounds seem
louder than they actually are.
 The compressor may make a pulsating or high-pitched sound.
 Water running from the evaporator to the water tank may make a splashing sound.
 Refrigerant flowing may make a gurgling sound.
 Fan sound may come from front and back air vents.
14 | P a g e
WATER DRAINAGE
The air conditioner has the capacity to dehumidify up to 81 pints per day. The patented selfevaporating function of the unit fully exhausts all condensation automatically in most environments
when humidity is less than 70%. Areas with more than 70% humidity, the self-evaporating function
can still exhaust about 98% of the moisture and the remaining 2% of moisture will be collected in
the water tank of the air conditioner.
When there is excess water condensation inside the unit, the air conditioner stops running and the
RED Stop light illuminates. The Stop light indicates that the water condensation needs to be
drained manually:
Manual Drainage
1. Turn off the unit.
2. Carefully roll the unit to a drain location or position a flat container, dish or optional drain bucket
accessory (sold separately) under the drain area of the lower drain port.
3. Remove the drain cover and rubber plug and the condensed water will drain out automatically.
4. Once all the condensed water is drained, replace the drain rubber plug and cover into the drain
firmly.
Continuous Gravity Drainage Option
This option is recommended if uninterrupted operation is desired.
1.
2.
3.
4.
Remove the drain plug cover and rubber plug from the upper drain port.
Install the drain hose (sold separately) through the drain cover.
Thread the drain cover onto the upper drain port.
Place the open end of the drain hose downward to an area appropriate for draining.
WARNING: The hose must be directed downward from the upper drain port to allow the
condensed water to flow with gravity.
Note: Please contact [email protected] for retail sales information or visit whynter.com for a
list of optional accessories.
15 | P a g e
CARE AND MAINTENANCE
IMPORTANT:
 Switch off the air conditioner and disconnect the plug from the power outlet
 Drain water by removing the drain plug.
 Always transport the air conditioner in an upright position only.
CLEANING THE PRE-FILTER
 To ensure the air intake is filtered properly and to assure that your air conditioner runs
efficiently, it is recommended to clean the Pre-filter at least once every two weeks.
 Switch off the air conditioner and pull out the filter frame from the unit.
 Remove the Activated Carbon filter from the Pre-filter.
 Use a vacuum cleaner or tap lightly to remove loose dust and dirt from the Pre-filter. Then
rinse it thoroughly under warm or cold running water (no hotter than 100F.)
 Dry thoroughly before re-inserting the filters.
 NOTE: The Activated Carbon filter is not washable. It should be replaced every 2-3 months or as
needed.
WARNING! Never operate the air conditioner without the filter in place.
CLEANING THE AIR CONDITIONER



Always switch off the air conditioner and disconnect the plug from the power supply outlet
before cleaning the air conditioner.
Use a soft damp cloth to wipe the body of the unit.
Never use harsh chemicals, oil-based products, detergents, chemically treated cloths or
other cleaning solutions. These could possibly damage the body of the air conditioner.
END OF SEASON STORAGE
This portable air conditioner comes with one end of season storage cover. We highly
recommend that storage cover bag is utilized when the unit is not going to be used for a
period of time.
WARNING: To avoid danger of suffocation, keep this bag away from babies and children.








Switch off the air conditioner and disconnect the power plug from the power supply outlet
before cleaning the air conditioner.
Clean the pre-filter.
Drain the condensed water completely.
On a warm day, set the unit to Fan only mode for half a day to dry the unit internally.
Gather the power cord and bundle it.
Remove the batteries from the remote.
If leaving the window kit in place, disconnect the exhaust and intake hose from the
window slider kit and place the included covers on the fixtures. Otherwise, remove the
window kit from the window opening. To remove the hose connectors from the fixtures
on the window kit, slightly turn, push and gently pull the connector to release.
Place the storage cover over the air conditioner.
NOTE:
Depending on use, it is recommended that the air conditioner be cleaned internally annually. Please
contact Whynter at [email protected] for internal maintenance cleaning instructions.
16 | P a g e
TIPS:
1. Keep the exhaust hose as short and straight as possible
The exhaust hose removes heat from the room. It should remain as short and straight as possible
without sharp bends or twists to maximize efficiency. If the exhaust hose must be extended, do
not exceed 9’.
2. Turn the air conditioner on early
Turning the air conditioner on early instead of waiting until the hottest point of the day will allow
the unit to be more effective. The air conditioner will not have to work as hard to cool the room
down and maintain the set temperature.
3. Reduce heat sources
Direct sunlight, televisions, computers and other heat generating appliances work against the air
conditioner by introducing heat into the space.
• Close window curtains and blinds to keep direct sunlight out
• Close doors and windows
• Keep ovens and stoves off
• Turn off unused lights
• Add weather stripping around windows and doors
4. Keep the air filter clean
Regular cleaning will help keep your air conditioner working properly. Dusty filters and vents
greatly reduce the airflow and efficiency of the unit.
• Clean the washable pre-filter regularly
• Replace the activated carbon filter every 2-3 weeks depending on use
• Vacuum any accumulated dust from around all vents
TECHNICAL DATA
Model
ARC-110WD
Cooling capacity
11,000 BTU
Power supply
115v/ 60Hz
Maximum power input
1040 Watts
Maximum input
9.5 Amps
Dehumidifying capacity
81 Pts / Day
Thermostat
61°F to 89°F
Refrigerant
R-410A
Air flow (max.)
300 m3/ Hour
Unit Dimensions
17.3” W x 15.4” D x 30.5” H
Package Dimensions
18.7” W x 19.5”D x 35”H
Unit Weight
62 lbs
17 | P a g e
TROUBLESHOOTING
Problem
The portable air
conditioner does not
turn on
Possible Causes
Power failure / outage.
Restore the power supply.
The automatic switch, line
fuse, or breaker has been
tripped.
Flip the switch / change the fuse / turn the
breaker back on. Also note that you may have
too many appliances drawing power on one
circuit, you may need to move the other
appliances to another circuit.
The power supply voltage is
too low.
The power cord is damaged.
The L.C.D.I. power plug for the
unit is tripped.
The unit turns on but
the compressor does
not turn on (the fan
runs but the unit is not
cooling)
The internal water reservoir is
full.
The room temperature is
outside of the operational
tolerances of the unit.
The Cooling mode is not on.
Move the unit onto another circuit with the
correct voltage.
Call for service. Only authorized personnel
should replace damaged power cord or power
plug.
Press the Reset button on the L.C.D.I. power
plug.
Drain water from the air conditioner.
This unit is designed to work in ambient
temperatures of 64°F to 95°F.
Press the MODE button until the COOL light
is shown on the display.
The compressor has not
turned on yet because of its
time delay.
Give the compressor 3 minutes to turn on
after the Cooling mode has been selected.
The set temperature is too
high.
Set the air conditioner to a lower temperature.
It is recommended to set the temperature to
at least 5°F of the ambient temperature.
The internal water reservoir is
full.
The air coming out of
the unit is not very
cold, or the airflow
volume is weak
Solutions
The filters are dirty or
obstructed.
The air intake or exhaust is
obstructed.
Either manually drain the water by removing
the drain plug or allow the unit to exhaust the
water itself by running the fan only mode.
Then cooling will resume.
Clean the air filters.
Make sure there is at least 20" of clearance
from the air intake. Make the length of the
exhaust hose is as short as possible.
The unit is set in DRY or FAN
mode.
Set the unit to the cooling mode.
The unit is set to low fan
speed.
Set the unit to a higher fan speed.
18 | P a g e
The unit has worked for
a long time, but the
room is not cold
enough
Windows or doors are open.
Close all windows and doors.
There are too many people in
the room.
You may need additional cooling or another
air conditioner.
There is direct sunshine into
the room.
Close curtains or blinds and try to minimize
the amount of direct sunlight into the room.
The room is a kitchen or with
many heat-producing
appliances
There is a server in the room.
The room is too large.
The unit is very noisy
The unit is not level.
The surface underneath the
unit is uneven.
Low power voltage.
The unit leaks water
The unit is tilted or not leveled
The water tank is full.
Fan speed cannot be
changed
Fan speed differences are not
very noticeable
19 | P a g e
You may need additional cooling or another
air conditioner.
You may need additional cooling or another
air conditioner.
You may need additional cooling or another
air conditioner.
Make sure the unit is on hard, level and
stable surface.
Move the unit to a location with a level and
hard floor.
Make sure the wall outlet and support the
required power consumption of the air
conditioner and do not use an extension cord.
Make use the unit is leveled.
Drain water from the drain plugs at the back
of the air conditioner.
The fan speed difference is not very
noticeable when the compressor is on. Try
setting the unit to Fan only mode, you should
be able to hear the difference between high
and low fan speed settings.
ONE YEAR LIMITED WARRANTY &
THREE YEAR WARRANTY ON COMPRESSOR
This WHYNTER product is warranted to the original owner, purchased from an authorized Whynter dealer within the 48
U.S. continental states, for one year from the original purchase date against defects in material and workmanship under
normal residential usage. Should your WHYNTER product prove defective within one year from the date of purchase,
contact Whynter’s Customer Support team with the serial number and proof of purchase to make a warranty claim. A
Return Authorization number must be issued before returning any parts or products. Parts or products received without
a Whynter issued Return Authorization number will be refused. Under this warranty, Whynter will repair or replace any
parts found defective with new or remanufactured parts or exchange the defective product with a new, refurbished, or
remanufactured product at our discretion. All defective products and parts covered by this warranty will be repaired or
replaced on a mail-in basis to Whynter’s Service Center. This warranty is not transferable. After the expiration of the
warranty, the cost of labor and parts will be the responsibility of the original owner.
The compressor of portable air conditioners is warranted for an additional two years after the one year limited warranty
expires from the date of purchase.
Return freight is prepaid by Whynter within two months of purchase. After two months to one year, the customer will be
responsible for the return freight cost to Whynter’s Service Center. Please package the product carefully in its original
packaging to avoid damage in transit. Whynter is not responsible for damage resulting from shipper mishandling or
improper packaging. Please retain the original box and packaging materials.
THIS WARRANTY DOES NOT COVER:
• Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes.
• Improper power supply such as power surge, low voltage, defective household wiring or inadequate fuses.
• Use in commercial or industrial applications.
• Damage, accidental or otherwise, to the product while in the possession of a consumer not caused by a defect in
material or workmanship.
• Damage caused by consumer misuse, tampering, lack of maintenance or failure to follow the care and special
handling provisions in the instructions.
• Damage to the finish of the case, or other appearance parts caused by wear.
• Damage caused by repairs or alterations to the product by anyone other than authorized by the manufacturer.
• Removal, Replacement Packaging, Freight and Insurance cost for the warranty service.
• Products sold AS IS or from an unauthorized reseller.
• Products that have had their serial numbers removed or defaced.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD
ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH
OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION
OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
The warranty, product contents and specifications are subject to change at any time without notice; please refer to
www.whynter.com for the most current information.
Please retain the original proof of purchase.
To register your warranty, please visit www.whynter.com and fill out the online
Warranty Registration form. Please be sure to include a copy of your purchase invoice.
To obtain service or information, contact Whynter LLC via email at
[email protected] or call 866-WHYNTER (866-949-6837).
Copyright © 2017 Whynter LLC
www.whynter.com
V 4.20.2017-1200
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement