advertisement
◉
Touch to zoom
Table of Contents Notice Installation .......................3 .......................4 Accessories Installation method Tips Introduction .......................7 Interface LED Buttons and Icons Operation .......................11 Switch on Switch off/on Loop recording Emergency recording Motion detection Play PC mode Mute Firmware upgrade Table of Contents Setting ......................14 Resolution Loop recording Exposure WDR Time-lapse Motion Detection GPS Speed Unit G-sensor LDWS(Lane Departure Warning System) FCWS(Forward Collision Warning System) Plate Stamp Date Stamp GPS Info Stamp Record Audio Screen Saver LED Date/Time Time Zone Language Beep Sound Frequency Format Format Warning Default Setting Version Customize Text Notice Installation ② Remove the paper from 3M sticker. Installation • Please do not install or operate with wet hands. • Please do not install in a location of high humidity, Installation Installation 3) Adjust the View Angle The sdjust the angle through turning the lens up/down . Accessories Introduction Introduction Introduction inflammable gas, liquid and position that may affect driver visibility and safety. (8) (9) • Please do not leave the device inside an airtight vehicle exposed to extreme heat. • Please do not use power that exceeds rated voltage. • Keep children away from products, accessories and pack. • Use only original charging cable.The manufacturer is not Car Adapter USB Cable GPS Mount (optional) 2) Connect to Car charger • Please do not press lens forcefully. • Please do not use sharp object against dashcam or accessories. • Please do not remove Micro SD card during recording and shutdown process to avoid file damage. • It is recommended to use a Class 10, 8 GB or above Micro SD Non-GPS Mount Clips Mount Detaching String Plug the cigarette adapter into your vehicle’s power port; Insert the USB plug (opposite end of the power) into the USB port on the camera. Note: ① For GPS version mount, please insert the USB plug into the USB port on the mount. ② For non-GPS version mount, just insert the USB plug into the USB port on the camera. Installation method 1) Install the Mount ① Slide the mount into the slot on the back of camera. card (64 GB SD is highest supported type). parked. If motion detection is enabled while driving, the camera may not continuously record. • It is recommended to keep the G-Sensor set to low (default (3) (4) (5) (1) (2) LED Color� Behavior To turn on/off device Solid� Red Power ON, Recording Back to previous menu Flashing Red 1. Power ON, not recording 2. Upgrading 1. To select the last video 2. To delete the video Playlist Mode driver visibility or safety. Stand-by Mode • Install device in a location close to the rearview mirror for the best view. • The lens should be positioned within the windshield wiper area to ensure a clear view on rainy days. (6) • Please do not install device on or near the area where the (7) ensure stable read and write. Note: Please do not install device on air bag or within its • Product function and contents of this manual may be working range.The manufacturer is not liable for any injury or death caused by deployment of air bag. changed without further notice. Enter Playlist Setting Menu Mode One click can start recording (2) Rec/Left (3) Menu (4) Emergency/Confirm (5) Mic/Right (6) USB Port (7) AV Out (8) Reset (9) Card Slot (10) USB Port Recording Mode To select the last feature To select the next feature ① Connect device to computer with mini-USB cable. ② Device will automatically turn on and “Mass Storage” will be 4) � Emergency recording 1) � Switch on Insert the Micro SD card into the card slot; then connect the car charger to the dashcam's mini USB interface and car cigarette lighter. Start the engine, then the device will switch on automatically. 2) � Switch off/on ①� Automatic: When the power is turned on, simply turn off the engine or unplug charging cable to switch it off automatically. ②� Manual: Switching the device off manually is required for vehicle models whose cigar lighter provides continuous power after the engine is turned off. ③ When the device has a power source, press and hold the power button switch at least 5 seconds to turn the device off. ④ Press the power button switch for at least 3 seconds to switch the device on. 3) � Loop recording 00:00:00 One click can turn off the screen, once again to turn on the screen (1) Power One click can back to recording mode 1080P60 Recording Mode 00:00:00 Recording Time 1080P60 Video Resolution One click can lock the file being recorded Recording Status One click can stop recording Emergency Lock One click can disable audio recording, once again to enable audio recording Microphone 2015/01/30 07:21:15 Operation ① Insert Micro SD card into card slot and automatic loop�� recording will begin after power is supplied. ② Time frame for each video file is 1/2/3/5/10 minutes. ③ When there is insufficient space on the Micro SD card, loop recording will automatically overwrite the old files one by one. ④ Loop recording files are saved in SD card: \DCIM\Movie folder. ①� Automatic emergency recording When the G-sensor is activated and a collision occurs, current footage will be locked automatically to avoid being overwritten by loop recording. (� Note: Collision sensing feature can be adjusted in settings under the ”G-sensor” option� ) ② Manual emergency recording Pressing the emergency recording button during footage recording will lock current footage to avoid being overwritten by loop recording. displayed. ③ The computer will detect “removable disk”. ④ There will be three folders under DCIM folder: ��� \Movie (loop recording video files) ��� \EMR (Emergency recording video file) ��� \Picture (Video snapshot) ⑤ Copy file needed to computer drive. 8) � Mute When you're talking something secret in your car, you just need to press the "Mic" button once to avoid the audio recorded by the dash camera. 9) � Firmware upgrade Setting Press the Menu button during video mode to access the settings. • FCWS (Forward Collision Warning System): • Resolution: • • • • • • • • • ① Download current firmware, unzip the file. Drag/drop or 5) � Motion Detection When this feature is activated, recording will begin if there is movement in front of the camera. Once the camera does not detect movement for 60 seconds, recording will be stopped and the device will switch to detect mode. The device will record again if� it� will� detect� a� new� movement in front of camera. 6) � Play ① Under video mode, press [ ② Using the arrow buttons [ ] button to access the playlist. MIC REC ] to select the desired video and press the button [����� ] to play. ③ Press the menu button to exit. copy/paste the bin file to root directory of the Micro SD card. ② Insert Micro SD card into device card slot after the file transfer is complete. ③ Plug into a power source and turn the device on. ④ LED indicator starts flashing for indication of upgrade. ⑤ Device will reboot automatically after upgrade is completed. ⑥� Access version option in the menu to check if the most current version is presented. Note: • Before using the micro SD card for upgrading the firmware, it is necessary to format it by the device to ensure stable writing and reading. • Do not unplug or power down the device during the system SD Card upgrade to prevent the booting from failing. • • • • Setting video resolution of footage recorded, 1920x1080P 60fps, 1920x1080P 30fps, 1280x720P 120fps, 1280x720P 60fps, 1280x720P 30fps,� are available for selection. Loop recording: Off/1/2/3/5/10 minutes. Exposure: Adjust the value of the EV(Exposure Value) to obtain better recording results under different light sources. Range is from -2.0 up to +2.0. Default is set at 0.0. WDR: Enable/disable WDR(Wide� Dynamic� Range) Time-lapse: Record� video� in� time� lapse� mode. Motion Detection: When this feature is activated, recording will begin if there is movement in front of the camera. Once the camera does not detect movement for 60 seconds, recording will be stopped and the device will switch to detect mode. The device will record again if it will detect a new movement in front of camera. GPS: Turns on/off GPS tracking. If disabled, your camera will no longer measure your� speed and position nor� synchronize the� time/date with the atomic clock. (only available when connect with� GPS signal) Please use “Dashcam Viewer” to playback videos and to visualize your� position and speed on your computer. Speed Unit: Sets the speed unit, kilometer per hour (KPH) or miles per hour(MPH). G-sensor: The G-sensor measures shock forces. The� settings from “low to high” determine the� amount of force needed to lock the file from� being overwritten. We recommend set it to low. LDWS (Lane Departure Warning System): When your vehicle is moving out of its lane on Highways, LDWS warns you by making alarm sound. Copyright (c) 2016,VIOFO Inc ., All rights reserved. -1- -2- -3- -4- -5- -6- -7- -8- -9- -10- -11- -12- -13- Setting Setting 7) � PC Mode To enter the feature selected One click can capture a photo film (window tint) or any other electronic product to ensure optimal use. to prevent from booting failure. One click can turn off the screen, once again to turn on the screen One click can disable audio recording, once again to enable audio recording • Install in a place where it will not be affected by the sun control • Please do not interrupt power supply during system upgrade Behavior Buttons One click can enter setting menu (10) 1. To select the next video 2. To lock/unlock the video 1. To enter the video selected 2. To play/pause the video To turn on/off device setting). airbag operates. • It is necessary to format Micro SD card before first use to Mode • Please do not install device in a location that will interfere with Operation Operation Buttons and Icons • Please do not turn on motion detection unless your vehicle is • Please do not disassemble the device and charging cable. Do not cut charging cable! Damage caused is not covered by warranty! Tips: Operation Introduction ③ Choose a suitable location for instation and make sure you have the best view possible. liable for damage resulting from the use of other charging cables. Introduction LED Interface TM VIOFO Notice Table of Contents TM Table of Contents -14- • • • • • • • • • • • • When your vehicle is getting closer to the front vehicle, FCWS warns you by the alarm sound. Plate Stamp: Imprints a customized set of 11 digits to the recorded video. Useful to add license plates or identifying features. Date Stamp: Imprints the time and date on the recorded video. GPS Info Stamp: Imprints the GPS information on the recorded video. Record Audio: Turns on and off the microphone. This can also be changed during recording by pressing the microphone button[ MIC ]. Screen Saver: Turns off the screen after the set time. LED: Turns on/off LED light. Date/Time: Setting system date/time. Time Zone: Sets the current time zone for GPS� time� and� date� calibration, note the time zone must be manually adjusted for daylight savings. Language: Set the language display of system to English, Traditional Chinese, and French, etc. Beep Sound: Turns on or off all notification sounds. Frequency: Adjusts the camera’s frequency setting to minimize flickering and banding in the recorded video. Format: The operation will delete all data in Micro SD card. ( Note: Once you format the card, all information will be deleted and cannot be restored. Make sure to back up all files before this step. ) Format Warning: Sets� the� format� warning� days. Default Setting: Restore device to factory settings. Version: Check the current firmware version of the device. Customize Text: Imprints the customize text on the recorded video. -15-
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project