Dura Faucet Limited Lifetime Warranty Dura Faucet products have been manufactured under the highest standards of quality and workmanship. Dura Faucet warrants to the original purchaser for as long as the original purchaser owns their RV that this product will be leak- and drip-free during normal use, and that all parts and finishes of this product will be free from defects in material and manufacturing workmanship. Plated metal and plated plastic finishes are warranted for (1) year. If the product should develop a leak or drip during the warranty period, Dura Faucet will, free of charge, provide the parts necessary to put the product back into good working condition by you. They may also replace any part or finish that proves defective in material and manufacturing workmanship, under normal installation, use and service, free of charge. Proof of purchase (original sales receipt) from the original purchaser must accompany all warranty claims. Defects or damages caused by the use of other products or parts is not covered by this warranty. If repair or replacement is not practical, Dura Faucet may elect to refund the purchase price in exchange for the return of the product. This warranty covers replacement of all defective parts and finishes. However, damage due to product abuse, product misuse, installation error, or the use of cleaners containing alcohol, abrasives, or other solvents, whether performed by a contractor, service company, or yourself, will void this warranty. Dura Faucet will not be responsible for labor charges and/or damages incurred in installation, repair or replacement, nor any indirect, incidental or consequential damages, losses, or injury costs of any nature relating to this product. Except as provided by law, this warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed or implied, statutory or otherwise, including without restriction those of merchantability or of fitness for use. Dura Faucet will advise you on how to proceed in making warranty claims. To begin a warranty claim, write to Dura Faucet explaining the defect and include proof of purchase and your name, address and telephone number. Email is [email protected] * Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents or other products not recommended for plated metal or plastic finishes. This will void the warranty. th 19215 SE 34 St. Ste. 106-382 Camas, WA 98607 DF-PK100 | Plastic Pull-Out RV Kitchen Faucet IN S T A LLA T IO N O F T H E F A U C E T 1 New Faucet Preparation Completely shut off the water supply. Remove the old faucet by disconnecting it from the water supply tubes under the sink. Clean the sink’s top surface in preparation for installation of the new faucet. 3 Install Faucet Under Sink Screw the provided locknuts upward from under the sink onto faucet connectors using your hands only. Tighten the nuts alternating until they are nearly flush with the underside of the sink top. Then, align the faucet as desired. While maintaining set alignment, tighten down the locknuts to lock faucet into place. Attach water supply lines to faucet by tightening nuts A and B. Do not overtighten. M A IN T E N A N C E A N D C L E A N IN G Cleaning Tips: The finish on your product is designed to retain its beautiful sheen for years. To maintain the original look of the finish, a little care and caution should be used. We recommend the use of mild soap and water to clean the product. THE USE OF ABRASIVE CLEANERS MAY SCRATCH THE FINISH OR CAUSE OTHER DAMAGE. RECOMMENDED TOOLS AND M A T E R IA LS ¨ ¨ ¨ Adjustable Wrench Plumbers Tape (Thread Seal Tape) Phillips Screw Driver B E F O R E Y O U B E G IN 2 Install Faucet and Basket Strainer on Sink Position the faucet onto the sink’s top. (A). Hand tighten locknuts. (B). If your sink is uneven, and the faucet does not sit flush, use silicone under the base. (R). Pass the hose through the faucet, and adjust the position of the faucet so that the hose does not rub against the edge of the sink hole. Attach the hose onto Check valve (M) and Wand assembly (P), and tighten securely. (S). Attach zinc weight to hose assembly as shown. 4 Connect to Water Supply Last step is to connect to the water supply. (G). Turn the faucet handles all the way on. (H). Next turn on both the hot and cold water supply and allow both the hot and cold water to run for at least one minute each. While the water is running, check for leaks around and under the sink. There are a variety of things to do before installing any new plumbing system into your home or residence. Before you begin work make sure you: ¨ ¨ ¨ ¨ Shut off the main water supply Cover your drain to prevent loss of parts Observed any local plumbing codes Inspect fixture for damage Replace as necessary * Dura Faucet reserves the right to make any revisions in the design of products without notice. 1. Stainless Steel Screw 2. ABS(BN) Handle 3. POM Ring 4. ABS(BN) Nut 5. POM/Rubber/Stainless Steel Cartridge-Hot 6. ABS(BN) Cylinder 7. POM/Brass/ABS/Rubber/Stainless/TPR Spray Gun Group 8. Rubber O-Ring 9. Rubber O-Ring 10. ABS(BN) Escutcheon 11. Rubber O-Ring 12. Rubber Washers (2) 13. Stainless Steel Springs 14. POM/Rubber Body 15. POM Base 16. Stainless Steel Spring 17. POM Heart Son 18. Rubber O-Ring 19. POM Cover 20. Rubber O-Ring 21. PP Base Plate 22. Stainless Steel Screws (2) 23. Pb Up Pb Chunk 24. PB Down Pb Chunk 25. ABS/Brass/PVC Hose Group 26. Stainless Steel Screws (2) 27. Rubber Washers (2) 28. ABS Mounting Nuts (2) 29. Rubber Washers (2) 30. ABS Coupling Nuts (2)
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021