advertisement
▼
Scroll to page 2
of 4
DriveRight CarChip Fleet & CarChip Fleet with Alarm Installation Instructions ® This manual provides installation instructions for CarChip Fleet (# 8241) and CarChip Fleet with Alarm (# 8245). CarChip Fleet with Alarm provides an audible warning to the driver whenever safe driving limits are exceeded. Refer to the DriveRight Fleet Management Software’s (FMS) Getting Started Guide, User’s Manual, and the software’s online Help for the additional information necessary to set up and use your CarChip Fleet or CarChip Fleet with Alarm. Note: The DriveRight FMS User’s Manual is in the Adobe Acrobat file “User’s Manual.pdf” located in the program folder. Before Installing CarChip Before installing CarChip Fleet or CarChip Fleet with Alarm in your vehicle, we recommend that you add the device to the database in the DriveRight Fleet Management Software (FMS) and check the CarChip settings. 1. Connect CarChip to your computer. See instructions on page 3. 2. Add the CarChip to your DriveRight FMS database. Note: Refer to the DriveRight FMS Help or User’s Manual for instructions on using DriveRight FMS. 3. In DriveRight FMS, verify the following CarChip settings and change if necessary: • • • • • Time and date Engine performance data parameters Speed bands Acceleration limits and deceleration limits LED State (Controls both the LED and alarm on CarChip Fleet with Alarm) 4. Use the Clear CarChip Memory command in the DriveRight FMS CarChip menu to clear the device’s memory. This step ensures that none of the manufacturing test data remains when you put your CarChip into service. Configuring CarChip Fleet with Alarm 1. Select the Set CarChip LED State command in DriveRight FMS CarChip menu. The Set CarChip LED State command controls the alarm and LED functions. 2. Select Enable to turn ON the alarm and LED, or select Disable to turn OFF the alarm and LED. 1 Installing CarChip The alarm functions in the following manner: • • • • Note: One beep when initially connected to the vehicle’s OBDII port. Two beeps when the vehicle’s OBDII protocol is identified. Five beeps for each acceleration & deceleration violation. Continuous beeps when violating the speed limit. The LED functions the same way in both CarChip Fleet models. Installing CarChip Use these instructions to install CarChip in your vehicle’s OBDII port. 1. Find the OBDII port on your vehicle. The OBDII port will be located within 3 feet of the steering wheel within or near the general area indicated by the dotted line in the illustration below. The port should be easily accessible to a person in the driver's seat. OBD II Port If you have trouble finding the OBDII port, be sure to check the following areas: • • • • • 2. Note: 2 Under the dash In front of the passenger seat Behind the ash tray Behind a small access panel in the dash In or around the center console Plug CarChip into the OBDII port checking to make sure the indicator light blinks when first connected. The indicator light will always blink when initially connected to a vehicle. Unless the indicator has been enabled via the software, it will stop blinking once it has established communications with the OBDII computer. Installing CarChip OBD II Port Indicator Light CarChip Fleet Connecting CarChip to Your Computer To connect the CarChip data logger to your computer using a USB connector: 1. Locate a free USB port on the front or back of your computer and insert the USB connector of the download cable into the USB port. 2. Plug the microminiature connector into the port on the CarChip data logger. 3 Contacting Davis Technical Support If you have questions, or encounter problems installing or operating your CarChip, first check the troubleshooting information in the DriveRight FMS Help and User’s Manual. If you are unable to resolve the problem or if you have questions about CarChip, please contact Davis Technical Support. Note: Please do not return items to the factory for repair without prior authorization. Phone Support: (510) 732-7814 – Monday – Friday, 7:00 a.m. – 5:30 p.m. Pacific Time. (510) 670-0589 – Fax to Technical Support. Email Support: [email protected] – E-mail to Technical Support. [email protected] – E-mail to Davis Instruments. Web Support: www.davisnet.com – Copies of User Manuals are available on the “Support” page. Watch for FAQs and other updates. CarChip and CarChip with Alarm Manual Rev. A, March 11, 2005 Document Part Number: 07395.284 For CarChip # 8241, 8245 CarChip® is a registered trademark of Davis Instruments Corp., Hayward, CA. © Davis Instruments Corp. 2005. All rights reserved. Information in this document subject to change without notice. 3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A. 510-732-9229 • Fax: 510-732-9188 E-mail: [email protected] • www.davisnet.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project