Woods HA35E Auger Operator's Manual

Woods HA35E Auger Operator's Manual
(Rev. 6/1/2017)
MAN0532
HA15E, HA20E, HA30E, HA35E
HA15EBOA, HA20EBOA, HA30EBOA
HA35EBOA
OPERATOR'S MANUAL
HYDRAULIC AUGER
TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual
are completed before releasing equipment to the owner.
The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that
all Dealer Check List items have been completed. Dealers can register all Woods product at
dealer.WoodsConstruction.net under Product Registration.
Failure to register the product does not diminish customer’s warranty rights.
TO THE OWNER:
Read this manual before operating your Woods equipment. The information presented will prepare you to do a better
and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and
become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals
can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at
www.WoodsEquipment.com, or in the United States and Canada call 1-800-848-3447.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces
provided:
Model: _______________________________
Date of Purchase: _____________________
Serial Number: (see Safety Decal section for location) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.
The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with
an exclamation mark) to indicate the degree of hazard for items of personal safety.
2 Introduction
CE Construction (Rev. 3/1/2016)
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 - 22
QUICK COUPLER KITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FITTING TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . .BACK COVER
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
(Rev. 2/15/2008)
MAN0532 (5/26/2006)
Introduction 3
SPECIFICATIONS
HA15E
HA15EBOA
HA20E
HA20EBOA
HA30E
HA30EBOA
HA35E
HA35EBOA
Drive
2" Hex
2" Hex
2" Hex
2" Hex
RPM @ 15 gpm (56.8 lpm)
76 rpm
49 rpm
N/A
N/A
RPM @ 20 gpm (75.7 lpm)
102 rpm
66 rpm
N/A
N/A
RPM @ 25 gpm (94.6 lpm)
126 rpm
85 rpm
N/A
N/A
RPM @ 30 gpm (114 lpm)
N/A
99 rpm
92 rpm
N/A
RPM @ 35 gpm (132.5 lpm)
N/A
N/A
109 rpm
107 rpm
RPM @ 40 gpm (151.4 lpm)
N/A
N/A
123 rpm
124 rpm
RPM @ 45 gpm (170.3 lpm)
N/A
N/A
N/A
138 rpm
1000 - 3500 psi
69 - 241 bar
1000 - 3500 psi
69 - 241 bar
1000 - 5000 psi
69 - 345 bar
1000 - 5000 psi
69 - 345 bar
Specifications
Pressure
Torque
7300 - 25500 lbs-in
825 - 2880 N-m
11200 - 39000 lbs-in 11995 - 59975 lbs-in 14854 - 74268 lbs-in
1265 - 4406 N-M
1355 - 6776 N-M
1678 - 8391 N-M
Bit Length
54 in. (137.2 cm)
Bit Diameter
6, 9, 12, 18, 24, 30 in
15, 23, 31, 46, 61, 76, 91 cm
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your auger. Read it carefully. It furnishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.
4 Introduction
The illustrations and data used in this manual were current at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
Throughout this manual, references are made to right
and left directions. These are determined by standing
behind the equipment facing the direction of forward
travel. Bit rotation is clockwise as viewed from the top
of the auger towards the bit.
(Rev. 2/15/2008)
MAN0532 (5/26/2006)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
INSTALLATION
 Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
 After connecting hoses, check that all control
lever positions function as instructed in the Operator's Manual. Do not put into service until control
lever and equipment movements are correct.
TRAINING
 Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer.) Failure to follow instructions or safety
rules can result in serious injury or death.
 If you do not understand any part of this manual
and need assistance, see your dealer.
 Know your controls and how to stop engine and
attachment quickly in an emergency.
 Operators must be instructed in and be capable
of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
 Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
 Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
Auger SR (Rev. 1/20/2006)
grene, serious injury, or death will result. CONTACT A P HYS ICIA N IM ME DIAT E LY IF FLU ID
ENTERS SKIN OR EYES. DO NOT DELAY.
 Never allow children or untrained persons to
operate equipment.
PREPARATION
 Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
 Counterweight ballast may be required for
machine stability. Check your power unit manual or
contact your dealer.
 Air in hydraulic systems can cause erratic operation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
 After connecting hoses, check that all control
lever positions function as instructed in the Operator's Manual. Do not put into service until control
lever and equipment movements are correct.
 Protective hose sleeves must cover all hydraulic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
 Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
(Safety Rules continued on next page)
Safety 5
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
 Keep bystanders away from equipment.
 Be sure attachment is properly secured,
adjusted, and in good operating condition. Coupler
lockpins must be fully extended and properly
engaged into attachment retaining slots.
 Do not operate or transport equipment while
under the influence of alcohol or drugs.
 Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
 Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
 Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
 Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
 Before drilling, check to make sure that you will
not drill into wires or other objects.
OPERATION
 Improper operation can cause the machine to
tip or roll over and cause injury or death.
• Keep power unit lift arms and attachment as
low as possible.
• Do not travel or turn with power unit lift arms
and attachment raised.
• Turn only on level ground.
• Go up and down slopes, not across them.
• Keep the heavy end of the machine uphill.
• Do not overload the machine.
 Never use attachment to carry loads that exceed
the rated operating capacity or other specifications
of the power unit. Check your power unit manual or
see your dealer for rated operating capacity.
Exceeding this capacity can cause machine to tip,
roll over, or present other hazards that can cause
injury or death.
 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.
 Consult local utilities before digging. Know
location and depth of all underground cables, pipelines, and other hazards in working area and avoid
contact.
 Contact with high voltage, overhead power
lines, underground cables, gas lines, and other
hazards can cause serious injury or death from
electrocution, explosion, or fire.
6 Safety
 Operate only in daylight or good artificial light.
 Always comply with all state and local lighting
and marking requirements.
 Do not allow riders. Do not lift or carry anybody
on the power unit or attachments.
 Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt/operator restraint, place transmission in park
or neutral, engage brake and ensure all other controls are disengaged before starting power unit
engine.
 When digging holes, always sit in operator seat.
 Keep digger under control by running drive
motor at slowest speed possible (no faster than
half-throttle).
 Look down and to the rear and make sure area
is clear before operating in reverse.
 Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
 Do not operate or transport on steep slopes.
 Do not stop, start, or change directions suddenly on slopes.
 Use extreme care and reduce ground speed on
slopes and rough terrain.
 Watch for hidden hazards on the terrain during
operation.
 Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,
using proper procedure. Inspect and repair any
damage before resuming operation.
 Never aim auger point with hands on auger,
gearbox, or boom. To place auger point use skid
steer arms.
TRANSPORTATION
 Use additional caution and reduce speed when
under adverse surface conditions, turning, or on
inclines.
(Safety Rules continued on next page)
Auger SR (Rev. 1/20/2006)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
 Reduce transport speed to avoid bouncing and
brief loss of steering control.
 Always comply with all state and local lighting
and marking requirements.
 Never allow riders on power unit or attachment.
 Turn off power to unit before transporting.
 Do not operate or transport on steep slopes.
 Do not operate or transport equipment while
under the influence of alcohol or drugs.
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.
 Be sure attachment is properly secured,
adjusted, and in good operating condition. Coupler
lockpins must be fully extended and properly
engaged into attachment retaining slots.
MAINTENANCE
 Never perform service or maintenance with
engine running.
 Before leaving operator's seat, lower lift arms
and put attachment on the ground. Engage brake,
stop engine, remove key, and remove seat belt.
 Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
 Before performing any service or maintenance,
lower digger to ground or block securely, turn off
skid steer engine, remove key, and disconnect
hydraulic lines from skid steer.
 Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
 NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
 Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
• Service work does not require going underneath.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
 Do not disconnect hydraulic lines until all system pressure is relieved. Lower unit to ground,
stop engine, and operate all hydraulic control
levers.
 Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
 Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its components in any way.
STORAGE
 Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifications and may be dangerous.
 Keep children and bystanders away from storage area.
 Follow manual instructions for storage.

Auger SR (Rev. 1/20/2006)
Safety 7
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
1 - Serial Number Plate
2 - PN D0196
3 - PN 54519
BE CAREFUL!
Use a clean, damp cloth to clean safety
decals.
Avoid spraying too close to decals when
using a pressure washer; high-pressure
water can enter through very small
scratches or under edges of decals causing
them to peel or come off.
Replacement safety decals can be ordered
free from your Woods dealer, or in the
United States and Canada call 1-800-3196637.
8 Safety
MAN0532 (5/26/2006)
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
4 - D0404
5 - PN 19924
6 - PN 46424
(Rev. 2/15/2008)
MAN0532 (5/26/2006)
7 - PN D0440
Safety 9
OPERATION
The operator is responsible for the safe operation of
the equipment. The operator must be properly trained.
Operators should be familiar with the equipment, the
tractor, and all safety practices before starting operation. Read the safety rules and safety decal instructions
on page 5 through page 9.
Augers are designed for one-man operation. You must
always dig holes while sitting in the operator’s seat. It
is the responsibility of the operator to see that no
one else is within twenty-five feet (25’) of the digger
when it is operating. Accidents have occurred when
more than one person is in the immediate area of the
operating equipment. Be sure no one else is near you
when you operate this product.
DANGER
 Do not put digger into service unless all shields
and guards are in place and in good condition.
Replace if damaged.
WARNING
 Never aim auger point with hands on auger,
gearbox, or boom. To place auger point use skid
steer arms.
 Do not shovel dirt away from a running auger.
The shovel could be caught and thrown by auger.
 Consult local utilities before working. Know
location of all underground cables, pipelines, overhead wires, and other hazards in working area and
avoid contact.
CAUTION
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
 Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
 When digging holes, always sit in operator seat.
PREPARATION
Thoroughly read and understand your Operator’s Manuals.
Before beginning operation, clear area of objects that
wrap around the auger or might be thrown.
Contact local utility companies to make certain there
are no buried gas lines, electrical cables, etc., in the
work area.
Check for ditches, stumps, holes, or other obstacles
that could cause the power unit to roll.
ATTACHING AUGER TO SKID STEER
1. Place the coupler latch handles in the unlocked
position (Figure 1). The latch handles must be
pulled to the UP position and the pins retracted.
 Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
 Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
 Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gangrene, serious injury, or death will result. CONTACT A PH YS ICIA N IM ME DIAT E LY IF FL U ID
ENTERS SKIN OR EYES. DO NOT DELAY.
Figure 1. Coupler Latches - Unlocked Position
 Do not put digger into service unless auger
point and all cutting edges are intact and in good
repair.
2. Rotate the skid steer attach slightly forward.
 Keep bystanders away from equipment.
3. Fully lower the lift arms.
10 Operation
MAN0532 (5/26/2006)
4. Pull forward to the auger. Be sure the outside of the
skid steer attachment coupler (1) is aligned with
the inside of the auger mounting adapter plate (2)
as shown in Figure 2.
14. Hook up the auxiliary hydraulic hoses. Be sure the
hoses are routed to prevent hose interference.
ATTACH AUGER TO BACKHOE
3
1
Figure 4. Attach Auger
1. Position the auger as shown in Figure 4.
2
DP2
Figure 2. Skid Steer to Auger Connection
5. Continue to pull forward until the skid steer
attachment coupler makes contact with the auger.
6. Raise the skid steer arms until the top of the skid
steer attachment coupler contacts the top latch bar
(3) on the auger mounting adapter plate.
2. Move the dipper stick of the backhoe so the
primary pin bore on the dipper stick is aligned with
the primary pin bore (1) on the auger.
3. Insert and secure the primary pin.
4. Activate the curl function until the curl pin bore is
aligned with the curl pin bore (2) on the auger.
5. Insert and secure the curl pin.
7. Roll the skid steer arms back until the auger is
completely off the ground.
8. Engage the parking brake on the skid steer.
9. Stop the engine.
10. Relieve the back pressure in the hydraulic system.
11. Exit the skid steer.
12. Move the coupler pins to the engaged position.
NOTICE
■
Do not over curl attachment. Over curling may
cause damage to host machine or attachment.
OPERATING TECHNIQUE
The auger is a hydraulically powered attachment
intended to drill in soil. The performance of the auger
can vary greatly depending on the skid steer, the soil
conditions, and the bit size. The following operating
procedure will help to ensure the best results.
NOTICE
■
If the auger should become stuck, stop the auxiliary hydraulic flow. Reverse the flow and slowly
lift the auger out of the hole and continue digging.
■
It may be necessary to adjust the position of
the power unit while operating auger to maintain a
vertical digging position.
4
Figure 3. Coupler Pin Fully Engaged
13. Make sure the coupler pins (4) are fully engaged
into the auger mounting adapter plate as shown in
Figure 3.
(Rev. 2/15/2008)
MAN0532 (5/26/2006)
1. Skid Steer: Raise the skid steer arms and roll the
attach frame forward. For proper operation the
attach frame should be rolled far enough forward
so the auger head does not rest against the cradle.
Backhoe: Extend the dipper arms and curl the
backplate outward. For proper operation the attach
frame should be rolled far enough forward so the
auger head does not rest against the cradle.
Operation 11
2. Position the auger bit over the desired hole
location.
2. Lower the auger so the bit is 10 to 15 inches from
the ground.
3. Lower the auger to the ground so the tip of the
auger just penetrates the ground.
3. Avoid excessive ground speed and sudden
maneuvers.
4. Bring the skid steer to high idle and activate the
auxiliary hydraulics.
5. Be sure the auger is operating in a clockwise
direction.
6. Lower the skid steer arms to apply downward
pressure to the auger.
7. If the auger stalls or slows down excessively,
reduce the downward pressure by raising the skid
steer arms.
8. Continue to lower the auger until a depth of
approximately 24 inches is reached.
9. Raise the auger to clean the hole of debris and
lower the auger again.
10. Continue digging, repeating step 9 as needed until
the desired depth is reached.
STORAGE
1. Store the auger inside when possible. If this is not
possible, store the auger on a pallet. Make sure the
auger is stored off the ground to protect the
couplers and hoses.
2. Cap
the
quick
contamination.
disconnects
to
prevent
PRE-OPERATION CHECKLIST
(OWNER RESPONSIBILITY)
___ Review and follow all safety rules and safety
decal instructions on page 5 through page 9.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
11. Once the desired depth is reached, allow the auger
to run a few seconds to clean the hole of debris.
___ Check that all shields and guards are properly
installed and in good condition. Replace if damaged.
12. Shut off the auxiliary hydraulics and raise the auger
out of the hole.
___ Check that equipment is properly and securely
attached to skid steer.
13. Skid Steer: Lower the skid steer arms while
rotating the backplate backward.
Backhoe: Retract the dipper and curl the
backplate inward.
___ Check that all hardware and cotter pins are properly installed and secured.
TRANSPORT
___ Check all lubrication points and grease as
instructed in Lubrication Information on page 13.
The post hole digger auger is free-swinging, and care
should be taken while transporting the machine.
Be sure auger is completely retracted from the hole
before attempting to move the skid steer.
Pay close attention to the Safety Messages regarding
transport. Avoid unnecessary injuries and equipment
damage by exercising cautious, conscientious travel
procedures.
1. Roll the skid steer arms or backhoe dipper
completely back and be sure the auger is resting in
the cradle.
___ Check and keep all bystanders away from equipment working area.
___ Check that all hydraulic hoses and fittings are in
good condition and not leaking before starting
tractor. Check that hoses are not twisted, bent
sharply, kinked, frayed or pulled tight. Replace
any damaged hoses immediately.
___ Consult local utilities before digging. Know location of and avoid contacting all underground
cables, pipelines, overhead wires and other hazards in digging area.
___ Check that auger point and all cutting edges are
intact and in good repair.

12 Operation
MAN0532 (5/26/2006)
OWNER SERVICE
The information in this section is written for operators
who possess basic mechanical skills. If you need help,
your dealer has trained service technicians available.
For your protection, read and follow all safety information in this manual.
WARNING
 NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going underneath.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
LUBRICATION INFORMATION
Replace the gearbox oil after the first 50 hours of operation. Thereafter, change the gearbox oil every year or
1000 hours of operation, whichever comes first. Use
only API 80W90 GL5 gear oil.
1. Position the auger so the head is oriented in a
vertical position with the auger shaft pointing
downward.
2. Remove the lower drain plug from the gearbox with
a 3/16" allen wrench as shown in Figure 5.
 Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
 Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
 Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
 Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gangrene, serious injury, or death will result. CONTACT A P HYS ICI AN I MME DIAT E LY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
DP4
Figure 5. Remove Drain Plug
3. Drain the oil from the gearbox into a suitable
receptacle.
4. Replace the drain plug.
5. Insert a 3/8" drive socket into the access hole in
the back of the chassis and remove the top filler
plug as shown in Figure 6.
ROUTINE MAINTENANCE
1. Check that all bolts, nuts, and screws are tight.
Checking the bolts and nuts on the cutting blades
is particularly important in rocky soil.
2. Check the level of the gearbox oil daily and top-off
at the correct level. Check for gearbox oil leaks. It
should be noted that no warranty claim can be
submitted on a gearbox that has run dry. It is
essential that the gearbox is kept correctly filled
with gearbox oil.
3. Check the wear on the cutting blades. Sharpen
them routinely with an angle grinder or replace
when worn down too far. Keep at least two sets of
cutting blades, bolts, and nuts as spares.
MAN0532 (5/26/2006)
DP5
Figure 6. Fill Plug Access
6. Add the required amount (31 oz) of oil to the
gearbox for HA15E/HA20E or (47 oz) of oil to the
gearbox for HA30E/HA35E.
7. Replace the oil fill plug.
Owner Service 13
CUTTING EDGE REPLACEMENT
Replacing Auger Teeth
2. Replace tooth (2) while maintaining the same
cutting angle.
Check the auger teeth daily for wear or damage.
Replace any worn or damaged teeth immediately to
prevent damage to the mounting bolts, nuts or auger
flighting. To increase the life of the cutting teeth, rotate
the outer tooth on one side with the inner tooth on the
other side.
1
3. Replace the mounting bolt (1) and torque to 85 lbsft. (115 N-m).
Replacing Pilot Bit
Check the pilot bit daily for wear or damage. Replace a
worn or damaged pilot bit immediately to prevent damage to the auger flighting.
To replace a pilot bit:
1. Remove bolt (1) as shown in Figure 8.
2. Remove and replace the pilot bit (2).
3. Replace bolt (1) and torque to 85 lbs-ft (115 N-m).
2
1
2
DP6
Figure 7. Cutting Edge Replacement
DP7
To replace or rotate a tooth:
1. Remove the mounting bolt (1), Figure 7.
Figure 8. Pilot Bit Replacement
Figure 9. Quick Coupler Instruction
14 Owner Service
(Rev. 6/1/2017)
MAN0532 (5/26/2006)
FLIGHTING REMOVAL
4
Removing Flighting
1. Remove the circle cotter (1) from the clevis pin as
shown in Figure 10.
3
2. Remove the clevis pin (2).
3. Slide the flighting from the shaft.
2
DP9
Figure 11. Skid Steer
1
DP8
3
Figure 10. Clevis Pin and Circle Cotter Location
2
1
Installing Flighting
1. Rotate the flighting so the 3/4" cross hole on the
flighting is oriented to the cross hole on the auger
shaft.
2. Slide the flighting onto the shaft.
3. Insert the clevis pin (2) and secure with the circle
cotter (1).
MOTOR/PLANETARY REMOVAL
1. Remove the flighting. (See “Flighting Removal” on
page 15.)
2. Remove the hoses from motor, plug the hoses and
cap the motor ports.
NOTE: A 1-7/16" crows foot wrench (supplied with
each unit) is needed to remove or install the
hydraulic hoses at the motor ports on HA30E,
HA30EBOA, HA35E and HA35EBOA models.
3. Position the auger on the backplate with the auger
head pointing up as shown in Figure 11 for skid
steer. For backhoe, position as shown in Figure 12.
4. Use a hoist to support the auger head (3).
(Rev. 6/13/2008)
MAN0532 (5/26/2006)
4
DP13
Figure 12. Backhoe
5. Skid Steer: Remove the planetary bolts (4).
Backhoe: Remove the snap ring (1) from one side
of the clevis pivot pin (2).
• Remove the clevis pivot pin.
• Remove the auger head assembly (3).
• Remove the planetary bolts (4).
6. Use a hoist to remove the chassis from the
motor/planetary assembly.
7. Place the motor/planetary assembly in a vice as
shown in Figure 13.
8. Remove the two motor bolts (6).
9. Remove the motor (7) from the planetary (8).
Owner Service 15
7
6
4. If the planetary does not have oil, use a funnel to
add oil through the motor input as shown in Figure
15. (For the type and amount of oil to be used see
Lubrication Information on page 13).
8
DP10
Figure 13.
INSTALLING MOTOR/PLANETARY
Figure 15. Fill Planetary, Motor Removed
1
2
Figure 14. HA15, HA20 Motor
1. Before reinstalling the planetary, we recommend
changing the planetary oil.
• Remove the oil drain plug using a 3/16" allen
wrench.
• Drain the oil in a suitable container.
2. Replace the drain plug.
3. Install the O-ring (2) onto the motor pilot (1) as
shown in Figure 14.
O-Ring Selection:
Model
HA15, HA20
O-Ring
HC516
16 Owner Service
10.
16.
17.
18.
O-ring, 2.239 x .07
1/2 NC Hex ut
1/2 Hardened flat washer
1/2 NC x 2-1/4 HHCS GR5
Figure 16. Planetary and Motor Assembly
5. Insert motor shaft into planetary. Make sure O-ring
(10) is in position. Align mounting holes and secure
into position using hardware previously removed.
6. Place planetary housing over motor and align
mounting holes. Secure using cap screws (18),
washers (17), and hex nuts (16). Torque to 77 lbs-ft
(105 N-m). See Figure 16.
MAN0532 (5/26/2006)
Skid Steer Assembly
1. Position the auger backplate flat on the ground
with cradle pointing up.
2. Lower the head assembly (A) onto the backplate
as shown in Figure 17.
3
3. Install the clevis pivot pin (13) and snap rings (12).
2
1
4. Install the motor fittings and hoses.
A
13
12
Figure 18. Backhoe
CLEANING POST HOLE DIGGER
After Each Use
12. Snap ring, .05 x 1.156
13. Pin, 1.25 x 7.32
Figure 17. Skid Steer
●
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Inspect machine and replace worn or damaged
parts.
●
Replace any safety decals that are missing or not
readable.
Backhoe Assembly
1. Lower the head assembly (3) on to the backplate
as shown in Figure 18.
Periodically or Before Extended Storage
●
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Remove the remainder using a low-pressure water
2. Install the clevis pivot pin (1) and snap rings (2).
3. Install the motor fittings and hoses.

MAN0532 (5/26/2006)
Owner Service 17
TROUBLESHOOTING
PROBLEM
Motor on the auger will not operate.
Auger bit rotates sluggishly.
Oil is leaking from the motor area.
O-rings on the fittings are damaged.
Insufficient cutting power.
Excessive oil temperature.
POSSIBLE CAUSE
SOLUTION
Auxiliary hoses are not hooked up to
the skid steer.
Inspect the connections visually
(make sure the QDs are fully
engaged).
There is an obstruction in one or
both of the auxiliary hoses.
Remove and inspect the hoses
visually.
One or more seals on the motor
have failed.
Contact your dealer.
Skid steer auxiliary hydraulics are
not operating properly.
Refer to the skid steer owner’s
manual.
Insufficient hydraulic flow from the
skid steer.
Refer to the skid steer owner’s
manual.
The hydraulic oil filter on the skid
steer is dirty.
Refer to the skid steer owner’s
manual.
One or more seals on the motor
have failed.
Contact your dealer.
One or more seals on the motor
have failed.
Contact your dealer.
O-rings on the fittings are damaged.
Visually inspect the O-rings and
replace as needed.
Fittings are loose or damaged.
Replace or tighten as required.
Hydraulic hoses are loose or
damaged.
Replace or tighten as required.
One or more seals on the motor
have failed.
Contact your dealer.
Oil filter on the skid steer is dirty.
Refer to the skid steer owner’s
manual.
Insufficient auxiliary flow from the
skid steer.
Refer to the skid steer owner’s
manual.
Relief valve on the skid steer is not
set properly.
Refer to the skid steer owner’s
manual.
Cutting teeth are worn.
Inspect the teeth and replace as
necessary.
Excessive downward force on the
auger.
Raise the skid steer arms slightly.
Auger bit is too large for the auger.
Consult Dealer Services about the
proper bit size.
Obstruction in one or both auxiliary
hydraulic hoses.
Remove, visually inspect, and
replace the hoses as necessary.
Hydraulic oil level on the skid steer
is low.
Refer to the skid steer owner’s
manual.
Hydraulic oil in the skid steer is dirty.
Refer to the skid steer owner’s
manual.
Hydraulic oil filter on the skid steer
is dirty.
Refer to the skid steer owner’s
manual.
Relief valve on the skid steer is not
set properly.
Refer to the skid steer owner’s
manual.
18 Troubleshooting
MAN0532 (5/26/2006)
DEALER CHECK LISTS
PRE-DELIVERY CHECK LIST
DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
(DEALER’S RESPONSIBILITY)
Inspect auger thoroughly after assembly to make sure
it is set up properly before delivering it to the customer.
The following check list is a reminder of points to
inspect. Check off each item as it is found satisfactory,
corrections are made, or services are performed.
___ Show customer how to make adjustments.
Describe the options available for this auger and
explain their purpose.
___ Check and grease all lubrication points as identified in Service, LUBRICATION INFORMATION,
page 13.
___ Point out all guards and shielding. Explain their
importance and the safety hazards that exist
when not kept in place and in good condition.
___ Check that flighting assembly has been properly
installed
___ Present Operator's Manual and request that customer and all operators read it before operating
equipment. Point out the manual safety rules,
explain their meanings and emphasize the
increased safety hazards that exist when safety
rules are not followed.
___ Check all bolts to be sure they are properly
torqued.
___ Check that all cotter pins are properly installed
and secured.
___ Check all hydraulic fittings to be sure they are
properly tightened.
___ Check all hydraulic hoses to be sure they are
properly tightened, routed, and secured.
___ Explain importance of lubrication to customer and
point out lubrication points on auger.
___ Explain to customer that when equipment is
transported on a road or highway, safety devices
should be used to give adequate warning to operators of other vehicles.
___ Check that pressure, return, and case drain lines
have the proper hydraulic couplers installed correctly.

MAN0532 (5/26/2006)
Dealer Check Lists 19
HA15E / HA15EBOA / HA20E / HA20EBOA BASE ASSEMBLY
Quick couplers and adapter fittings
are included in HA15E & HA20E
kits. See items 22 and 23 for part
numbers.
Note: Use two adapters (8) to connect male and female quick couplers to hose (21) for HA15E &
HA20E augers.
REF
PART
QTY
DESCRIPTION
REF
PART
QTY
DESCRIPTION
1
1026701
1
Auger attach frame, (Skid Steer) - or -
12
1
1026696
1
Auger attach frame, (Backhoe)
13 1011884
AR Pin, 1.25 x 7.32 (Skid Steer) - or -
2
1026697
1
Auger chassis
13
T1118
AR Pin, 1.25 x 12.89 (Backhoe)
3
1020762
1
Auger clevis
14
70362
4
104251
M0030
AR Retaining ring, 1.25" ext. (Backhoe)
2
1/2 NC x 1-1/2 SHCS
1
Pin, auger shaft 3/4 x 4
15
855 *
2
1/2 Lock washer
5
10378 *
2
1/4 NC x 1 Hex head cap screw GR5
16
1093 *
6
1/2 NC Hex nut
6
5288 *
2
1/4 NC Hex nut
17
57816
18 1/2 Hardened flat washer
7
5336 *
4
1/4 Flat washer
18
25474 *
9
1/2 NC x 2-1/4 HHCS GR5
8
F1087
4
Fitting, 7/8 ORBM x 7/8 JICM
19 1026530
1
Manual tube assembly
9
HC421
1
Motor - HA15 - or -
20
72449 *
1
.1 x 2 Circle cotter
9
1020763
1
Motor - HA20
21
H1128
2
Hose, 115" x 3/4 JICF x 3/4 JICF (NS)
9a S0100111
1
Seal kit, for HA15, HA20 motor (NS)
22
HC546
1
QD 1/2 Flush face, female (NS)
10
HC516
1
O-Ring, 2.239 ID x .07 W
23
HC547
1
QD 1/2 Flush face, male (NS)
11
1020767
1
Planetary - HA15, HA20 hex
NS 1026695
1
Decal set
11a S0100875
1
Seal and bearing kit,
for 1020767 planetary (NS)
AR As required
11b
HC054
1
Shaft seal for 1020767 planetary (NS)
NS Not shown
12
63236
AR Retaining ring, .05 x 1.156 ext.
(Skid Steer) - or -
20 Parts
*
Standard hardware, obtain locally
(Rev. 2/15/2008)
MAN0532 (5/26/2006)
HA30E / HA30EBOA / HA35E / HA35EBOA BASE ASSEMBLY
REF
PART
QTY
DESCRIPTION
REF
PART
QTY
DESCRIPTION
1
1026703
1
Attach frame with decals (skid steer)
14
T1118
1
Pin, 1.25 x 12.89 SR 12.25 (backhoe)
1
1026696
1
Attach cradle with decals (backhoe)
15
21660
2
HHCS 1/2 NC x 1-1/4 GR8
2
1026702
1
Auger chassis with decals
16
2
Washer, lock 1/2
3
1021808
1
WA Clevis
17
8
Nut, lock 1/2 NC
4
104251
1
Pin, Auger shaft 3/4 x 4
18
57816
16 Washer 1/2 SAE flat hardened
25474 *
8
HHCS 1/2 NC x 2-1/4 GR5
1
Manual tube
5
10378 *
2
HHCS 1/4 NC x 1 GR5
19
6
70065 *
2
Nut whiz 1/4 NC
20
7
5336 *
855 *
765 *
1026530
2
Washer 1/4 flat ZP
21
1
.1 x 2 Circle cotter
8
F1293
2
Fitting, 12OM x 12SLM 90°
22
1025572
2
9
F1283
1
Fitting, 10OM x 8SLM 90°
Hose 3/4 x 104 12SLF 12SLF 5000
(not shown)
10
HC321
1
Motor, Sunstrand M33-3004 (HA30E)
23
1025573
1
10
HC551
1
Motor, M44-12 Tooth Sauer-Dan
(HA35E)
Hose 1/4 x 104 8SLF 8SLF R1 (not
shown)
24
1026695
1
Decal set (not shown)
25 S0100358
1
Seal, shaft Sundstrand M35 (HA30E)
(not shown)
26 S0100009
1
Seal, oil Fairfield S2B (HA35E)
(not shown)
27
1007655
1
Seal kit MMF035 for HC550/551
(HA35E) (not shown)
28
1022557
1
Wrench, offset 1.44" crows foot
11
HC536
1
O-Ring, 2-155 SAE 4" OD
12
HC389
1
Planetary, Auburn HA30 hex
13
63236
4
Ring set, .050 x 1.156 (skid steer)
13
63236
2
Ring set, .050 x 1.156 (backhoe)
13
M0030
2
Retaining ring 1-1/4" ext (backhoe)
14
1011884
2
Pin, 1.25 x 7.32 (skid steer)
14
1011884
1
Pin, 1.25 x 7.32 (backhoe)
72449 *
*
(Rev. 6/13/2008)
MAN0532 (5/26/2006)
Standard hardware, obtain locally
Parts 21
AUGER ASSEMBLY
REF
PART
PART
QTY
DESCRIPTION
1
Round
FA6
Hex
FAH6
1
6" Auger
1
1
FA9
FA12
FAH9
FAH12
1
1
9" Auger
12" Auger
1
1
FA15
FA18
FAH15
FAH18
1
1
15" Auger
18" Auger
1
1
FA24
FA30
FAH24
FAH30
1
1
24" Auger
30" Auger
1
1
FA36
FA18TR
FAH36
NA
1
1
36" Auger
18" Tree auger
1
1
FA24TR
FA30TR
FAH24TR
FAH30TR
1
1
24" Tree auger
30" Tree auger
1
2
FA36TR
102282
FAH36TR
102282
1
1
36" Tree auger
Tri-flow bit
2
3
104066-1
102281
104066-1
102281
1
Tri-flow carbide bit
40/50 Tooth - standard
3
3
S0100560
104065-1
S0100560
104065-1
40/50 HFF - optional
40/50 Carbide tooth - optional
4
4
3034959
B0842 *
3034959
B0842 *
1/2 NC x 1-1/2 Carriage bolt
5
5
3034960
765 *
3034960
765 *
1/2 NC Lock nut
6
6
1637 *
10380 *
1637 *
10380 *
7
8
3035060
R256
3035060
H200
1/2 NC x 3-1/2 HHCS GR5
1/2 NC x 4 HHCS GR5
Hardware kit
Interchangeable collar
* Standard hardware, obtain locally
TOOTH REQUIREMENTS
22 Parts
40/50
Tooth
40/50
HFF
Tooth
40/50
Carbide
tooth
2
2
2
6" Auger
4
4
4
9" Auger
4
4
4
12" Auger
5
5
5
15" Auger
6
6
6
18" Auger
8
8
8
24" Auger
Auger
10
10
10
30"Auger
12
12
12
36" Auger
8
8
8
18" Tree auger
9
9
9
24" Tree auger
11
11
11
30" Tree auger
12
12
12
36" Tree Auger
(Rev. 6/1/2017)
MAN0532 (5/26/2006)
BoRH HEAD
REF
(Rev. 6/1/2017)
MAN0532 (5/26/2006)
PART
QTY
DESCRIPTION
1
3034961
BoRH Replacement tooth
2
3034962
6 - BoRH
2
3034963
9 - BoRH
2
3034964
12 - BoRH
3
3035170
6" BoRH Wear cap
3
3035171
9" BoRH Wear cap
3
3035172
12" BoRH Wear cap 1
4
3035173
12" BoRH Wear cap 2
5
765
1/2 NC Hex lock nut
5
3034960
1/2 NC Hex lock nut
6
1637
1/2 NC x 3-1/2 HHCS, GR5
7
C257595
1/2 NC x 1-3/4 HHCS, GR5
Parts 23
QUICK COUPLER KITS
High-Flow with Auxiliary
High-Flow with No Auxiliary
Low-Flow
QC Kit
Description
QC Kit
Description
QC Kit
Description
Bobcat
HC356
Flush Face
HC355
Flush Face
HC357
Flush Face
HC243
Poppet
HC211
Ag Ball Valve
HC279
Flush Face
HC211
Ag Ball Valve
Vintage
Make
1013825
Flush Face
HC278
Flush Face
HC209
Flush Face &
Ag Ball Valve
Cat
HC538
Flush Face
1014196
Flush Face
1014197
Flush Face
Daewoo
HC209
Flush Face
HC212
Flush Face
HC211
Ag Ball Valve
Gehl
HC398
Flush Face
1014195
Flush Face
HC400
Flush Face
HC305
Poppet &
Ag Ball
Vintage
Vintage
Case
HC212
Flush Face
John Deere
1014198
Flush Face
1013826
Flush Face
HC310
Flush Face
Komatsu
1013834
Flush Face
1013833
Flush Face
1013835
Flush Face
New Holland
1014199
Flush Face
HC308
Flush Face
HC310
Flush Face
Scat Trak
HC537
Flush Face
HC243
Poppet
QUICK COUPLER KIT COMPONENTS
QC KIT
HC209
HC211
HC212
HC278
HC279
Includes
Style
Male/Female
Body
Size
Hose End
HC193
Flush Face
Male
3/4
SAE #12 O-ring
HC194
Flush Face
Female
3/4
SAE #12 O-ring
HC195
Ag Ball
Female
1/2
1/2-14 NPT
HC196
Ag Ball
Male
1/2
1/2-14 NPT
HC197
Flush Face
Female
1/2
SAE #10 O-ring
HC195
Ag Ball
Female
1/2
1/2-14 NPT
HC196
Ag Ball
Male
1/2
1/2-14 NPT
HC193
Flush Face
Male
3/4
SAE #12 O-ring
HC194
Flush Face
Female
3/4
SAE #12 O-ring
HC197
Flush Face
Female
1/2
SAE #10 O-ring
HC193
Flush Face
Male
3/4
SAE #12 O-ring
HC194
Flush Face
Female
3/4
SAE #12 O-ring
HC197
Flush Face
Female
1/2
SAE #10 O-ring
HC201
Flush Face
Male
1/2
SAE #10 O-ring
HC197
Flush Face
Female
1/2
SAE #10 O-ring
HC201
Flush Face
Male
1/2
SAE #10 O-ring
24 Quick Coupler
Quick Coupler Chart (Rev. 10/13/2006)
QUICK COUPLER KIT COMPONENTS
QC KIT
HC308
HC310
HC355
HC356
HC357
HC398
HC400
HC537
HC538
1013825
1013826
1013833
Includes
Style
Male/Female
Body
Size
Hose End
HC416
Flush Face
Female
5/8
SAE #12 O-ring
HC417
Flush Face
Male
5/8
SAE #12 O-ring
HC418
Flush Face
Male
3/8
SAE #8 O-ring
HC414
Flush Face
Male
1/2
SAE #12 O-ring
HC415
Flush Face
Female
1/2
SAE #12 O-ring
HC344
Flush Face
Male
12 mm
SAE #12 O-ring
HC345
Flush Face
Female
12 mm
SAE #12 O-ring
HC346
Flush Face
Female
9 mm
SAE #8 O-ring
HC342
Flush Face
Female
7 mm
SAE #6 O-ring
HC343
Flush Face
Male
7 mm
SAE #6 O-ring
HC344
Flush Face
Male
12 mm
SAE #12 O-ring
HC345
Flush Face
Female
12 mm
SAE #12 O-ring
HC346
Flush Face
Female
9 mm
SAE #8 O-ring
HC344
Flush Face
Male
12 mm
SAE #12 O-ring
HC345
Flush Face
Female
12 mm
SAE #12 O-ring
HC344
Flush Face
Male
12 mm
SAE #12 O-ring
HC345
Flush Face
Female
12 mm
SAE #12 O-ring
HC346
Flush Face
Female
9 mm
SAE #8 O-ring
HC344
Flush Face
Male
12 mm
SAE #12 O-ring
HC345
Flush Face
Female
12 mm
SAE #12 O-ring
HC415
Flush Face
Female
1/2
SAE #12 O-ring
HC416
Flush Face
Female
5/8
SAE #12 O-ring
HC417
Flush Face
Male
5/8
SAE #12 O-ring
HC418
Flush Face
Male
3/8
SAE #8 O-ring
HC521
Flush Face
Female
16 mm
SAE #12 O-ring
HC522
Flush Face
Male
16 mm
SAE #12 O-ring
1532994
Flush Face
Female
3/4
SAE #12 O-ring
1532995
Flush Face
Male
3/4
SAE #12 O-ring
1532997
Flush Face
Female
1/2
SAE #8 O-ring
HC417
Flush Face
Male
5/8
SAE #12 O-ring
HC418
Flush Face
Male
3/8
SAE #8 O-ring
HC545
Flush Face
Female
5/8
SAE #12 O-ring
HC546
Flush Face
Female
1/2
SAE #10 O-ring
HC547
Flush Face
Male
1/2
SAE #10 O-ring
HC343
Flush Face
Male
7 mm
SAE #6 O-ring
HC521
Flush Face
Female
16 mm
SAE #12 O-ring
HC522
Flush Face
Male
16 mm
SAE #12 O-ring
HC415
Flush Face
Female
1/2
SAE #12 O-ring
HC521
Flush Face
Female
16 mm
SAE #12 O-ring
HC522
Flush Face
Male
16 mm
SAE #12 O-ring
Quick Coupler Chart (Rev. 10/13/2006)
Quick Coupler 25
QUICK COUPLER KIT COMPONENTS
QC KIT
1013834
Includes
Style
Male/Female
Body
Size
Hose End
HC414
Flush Face
Male
1/2
SAE #12 O-ring
HC415
Flush Face
Female
1/2
SAE #12 O-ring
HC521
Flush Face
Female
16 mm
SAE #12 O-ring
HC522
Flush Face
Male
16 mm
SAE #12 O-ring
1013835
46058
Flush Face
M/F Set
3/4
SAE #12 O-ring
1014195
HC344
Flush Face
Male
12 mm
SAE #12 O-ring
HC345
Flush Face
Female
12 mm
SAE #12 O-ring
HC346
Flush Face
Female
9 mm
SAE #8 O-ring
HC521
Flush Face
Female
16 mm
SAE #12 O-ring
HC522
Flush Face
Male
16 mm
SAE #12 O-ring
1532997
Flush Face
Female
1/2
SAE #8 O-ring
1014196
1014197
1014198
1014199
1532994
Flush Face
Female
3/4
SAE #10 O-ring
1532995
Flush Face
Male
3/4
SAE #10 O-ring
HC343
Flush Face
Male
7 mm
SAE #6 O-ring
HC414
Flush Face
Male
1/2
SAE #12 O-ring
HC415
Flush Face
Female
1/2
SAE #12 O-ring
HC521
Flush Face
Female
16 mm
SAE #12 O-ring
HC522
Flush Face
Male
16 mm
SAE #12 O-ring
HC414
Flush Face
Male
1/2
SAE #12 O-ring
HC415
Flush Face
Female
1/2
SAE #12 O-ring
HC416
Flush Face
Female
5/8
SAE #12 O-ring
HC417
Flush Face
Male
5/8
SAE #12 O-ring
HC418
Flush Face
Male
3/8
SAE #8 O-ring
26 Quick Coupler
Quick Coupler Chart (Rev. 10/13/2006)
FITTING TORQUE CHART
Always tighten fittings to these values unless a different torque value is listed
for a specific service procedure.
Make sure fastener threads are clean and threads are engaged properly.
All torque values are adopted from SAE J514 and SAE J1453.
Size
SAE (JIC)
37° Flare Thread
Size
O-Ring Style
Straight Thread
Size
Seal-Lok
Thread
2
5/16 - 24
5/16 - 24
---
3
3/8 - 24
3/8 - 24
---
4
7/16 - 20
7/16 - 20
9/16 - 18
5
1/2 - 20
1/2 - 20
---
6
9/16 - 18
9/16 - 18
11/16 - 16
8
3/4 - 16
3/4 - 16
13/16 - 16
10
7/8 - 14
7/8 - 14
1 - 14
12
1-1/16 - 12
1-1/16 - 12
1-3/16 - 12
14
1-3/16 - 12
1-3/16 - 12
---
16
1-5/16 - 12
1-5/16 - 12
1-7/16 - 12
20
1-5/8 - 12
1-5/8 - 12
1-11/16 - 12
24
1-7/8 - 12
1-7/8 - 12
2 - 12
32
2-1/2 - 12
2-1/2 - 12
---
TORQUE
SAE
Dash
Size
Lbs-Ft
N-m
Lbs-Ft
N-m
Lbs-Ft
N-m
2
4
5
4
5
---
---
3
8
11
9
12
---
---
4
12
16
16
22
18
25
5
15
20
22
30
---
---
6
18
25
35
48
27
37
8
37
50
60
82
40
54
10
48
65
105
143
63
86
12
74
100
140
190
92
125
14
88
120
184
250
---
---
16
100
135
221
300
122
165
20
133
180
258
350
147
200
24
166
225
317
430
166
225
32
236
320
---
---
---
---
SAE 37° Flare
Fitting Torque Chart (7/15/2005)
O-Ring Straight Thread
Seal-Lok
Appendix 27
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE SERIES
TORQUE
CHART
A
SAE Bolt Head
Identification
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
1/4"
5/16"
7/16"
1/2"
6
12
8
17
10
19
13
26
14
27
18
37
3/8"
7/16"
9/16"
5/8"
23
36
31
48
35
55
47
75
49
78
67
106
1/2"
9/16"
3/4"
13/16"
55
78
75
106
85
121
115
164
120
171
163
232
5/8"
3/4"
15/16"
1-1/8"
110
192
149
261
170
297
230
403
240
420
325
569
7/8"
1"
1-5/16"
1-1/2"
306
467
416
634
474
722
642
979
669
1020
907
1383
A
METRIC SERIES
TORQUE
CHART
A
Metric Bolt Head
Identification
8.8
Metric
Grade 8.8
10.9
Metric
Grade 10.9
COARSE THREAD
FINE THREAD
MARKING ON HEAD
MARKING ON HEAD
A
Diameter &
Thread Pitch
(Millimeters)
Wrench
Size
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
Diameter &
Thread Pitch
(Millimeters)
6 x 1.0
10 mm
8
6
11
8
8
6
11
8
6 x 1.0
8 x 1.25
10 x 1.5
13 mm
16 mm
20
39
15
29
27
54
20
40
21
41
16
30
29
57
22
42
8 x 1.0
10 x 1.25
12 x 1.75
14 x 2.0
18 mm
21 mm
68
109
50
80
94
151
70
111
75
118
55
87
103
163
76
120
12 x 1.25
14 x 1.5
16 x 2.0
18 x 2.5
24 mm
27 mm
169
234
125
172
234
323
173
239
181
263
133
194
250
363
184
268
16 x 1.5
18 x 1.5
20 x 2.5
22 x 2.5
30 mm
34 mm
330
451
244
332
457
623
337
460
367
495
270
365
507
684
374
505
20 x 1.5
22 x 1.5
24 x 3.0
30 x 3.0
36 mm
46 mm
571
1175
421
867
790
1626
583
1199
623
1258
459
928
861
1740
635
1283
24 x 2.0
30 x 2.0
Typical Washer
Installations
Bolt
Metric 8.8
Lock Washer
Metric 10.9
Metric 8.8
Metric 10.9
Flat Washer
8/9/00
28 Appendix
Bolt Torque & Size Charts (Rev. 3/28/2007)
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
IN
MM
5/8
3/4
7/8
1
2
3
4
5
6
7
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM
10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG............................................................... Agriculture
ASABE .................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP ............................ British Standard Pipe Parallel
BSPTM ................British Standard Pipe Tapered Male
CV .................................................... Constant Velocity
CCW .............................................. Counter-Clockwise
CW ...............................................................Clockwise
F....................................................................... Female
FT .............................................................. Full Thread
GA..................................................................... Gauge
GR (5, etc.) ...........................................Grade (5, etc.)
HHCS........................................ Hex Head Cap Screw
HT ........................................................... Heat-Treated
JIC ................ Joint Industry Council 37° Degree Flare
LH .................................................................Left Hand
LT ........................................................................... Left
m ......................................................................... Meter
mm ................................................................Millimeter
M .......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
MPa .........................................................Mega Pascal
N...................................................................... Newton
NC ......................................................National Coarse
NF........................................................... National Fine
NPSM .....................National Pipe Straight Mechanical
NPT .......................................... National Pipe Tapered
NPT SWF .........National Pipe Tapered Swivel Female
ORBM........................................... O-Ring Boss - Male
P ...........................................................................Pitch
PBY ...................................................... Power-Beyond
psi ..........................................Pounds per Square Inch
PTO ..................................................... Power Take Off
QD ....................................................Quick Disconnect
RH ..............................................................Right Hand
ROPS ........................... Roll-Over Protective Structure
RPM ....................................... Revolutions Per Minute
RT........................................................................ Right
SAE ..........................Society of Automotive Engineers
UNC......................................................Unified Coarse
UNF .......................................................... Unified Fine
UNS......................................................Unified Special
Appendix 29
WARRANTY
Construction Equipment
Please Enter Information Below and Save for Future Reference.
Date of Purchase: ___________________________
From (Dealer): ______________________________________
Model Number: _____________________________
Serial Number: ______________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defects in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be twelve (12) months commencing on the in-service date of the product or fifteen months after
shipment from the factory or 2,000 hours of service, whichever occurs first. Proof of the in-service date must be provided for claims involving
product that originally shipped more than twelve (12) months prior to the date of the claim.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, inappropriate application or an accident. This Warranty does not apply in the event that the
product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a
WOODS authorized service center. This Warranty does not cover normal wear and tear, or normal maintenance items, as more specifically
described below. This Warranty also does not cover repairs made with parts other than those obtained through WOODS.
This Warranty is extended solely to the original purchaser of new and unused product, including, but not limited to, purchases made from
authorized Woods dealers. Should such original purchaser sell or otherwise transfer this product to a third party, this Warranty does not transfer
to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, WOODS specifically disclaims any damages relating to (i) lost profits, business,
revenue or goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (iii) any other type of damage to
property or economic loss.
This Warranty is subject to any existing conditions of supply, which may directly affect WOODS’ ability to obtain materials or manufacturer
replacement parts.
No agent, representative, dealer, distributor, serviceperson, or employee of any company, including without limitation, WOODS, its authorized
dealers, distributors, and service centers, is authorized to alter, modify or enlarge this Warranty.
Contact an authorized WOODS dealer or service center for warranty service. Common issues that would NOT be covered by this Warranty
Policy include, but are not limited to, the examples listed below this Policy.
WOODS®| A Blount International Brand
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
woodsequipment.com
Examples of Common, Non-Covered Claims
1. The owner and operator are responsible for maintaining weld integrity on attachments subject to weld erosion from ongoing contact with soils, rocks,
and other materials. Different materials have differing abrasive characteristics that will erode the structural welds of ground-engaging attachments at
differing rates. Structural failures may occur as a result of excessive weld erosion. The owner and operator are responsible for maintaining necessary
weld sizes and re-welding eroded welds with industry-approved procedures. Woods will not accept warranty claims for weld erosion or structural
failures of the attachment as a result of weld erosion.
2. Attachments are used extensively in ground-engaging operations and, as a result, the teeth, tooth holders, cutting edges, bucket edges, ripper shanks, and
other portions of the attachment are subject to abrasion and resulting wear. Woods will not accept warranty claims for wear of components or wear of
areas of the attachment subject to ground-engaging wear.
3. The owner and operator are responsible for examining the attachment for any weld or structural cracking. Any such cracking caused by a defect in
materials or workmanship by Woods will be covered under the Woods Warranty Policy. If the owner or operator continues to operate the attachment
after weld cracking or structural cracking is visible or should have reasonably been visible, and as a result of continued operation, additional damage to
the attachment results, Woods will not accept responsibility for the additional damage caused to other welds or to the attachment structure.
4. Materially modifying Woods attachments may result in premature failures of the attachment. Woods will not accept warranty claims on attachments that
have been materially modified.
5. Misapplications of attachments may result in premature wear, breakage, or structural failures of the attachment. Woods will not accept warranty claims
on attachments that have been misapplied. For instance, using a general purpose excavator bucket in an application requiring a heavy or severe duty
bucket or using the excavator bucket as a “jack hammer” to break concrete are considered misapplications.
©2016 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
W-10023-V CE Manuals (Rev. 3/9/2016)
WARRANTY
(Replacement Parts For All Models Except Mow’n MachineTM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser
with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty
does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or
otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any
way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this
Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after
such defect or noncompliance is discovered or should have been discovered, routed through the dealer and
distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete
such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO
OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS
WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly
or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty,
negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing,
Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of
crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain
materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including
without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify,
or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
WOODS®| A Blount International Brand
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
woodsequipment.com
©2017 Woods Equipment Company. All rights reserved. Woods® and the Woods logo are trademarks of Woods Equipment Company. All other
trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective
companies or mark holders. Specifications subject to change without notice.
F-8494 (Rev. 1/3/2017)
PART NO.
MAN0532
WOODS®| A Blount International Brand
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
woodsequipment.com
© 2017 Woods Equipment Company. All rights reserved. Woods® and the Woods logo are trademarks of Woods Equipment Company. All other
trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement