Elba HF60CSX2 User guide

Elba HF60CSX2 User guide
Installation instructions
and user guide
Canopy rangehoods
HC60PCIX1 & HC90PCIX1 models
NZ AU
Contents
Safety and warnings
Installation instructions
Using your rangehood
Care and cleaning
Manufacturer’s warranty
Customer care
1
2
3
7
8
9
10
Important!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not be available in all markets and are subject to change at any
time. For current details about model and specification availability in your country, please go to our website
www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
2
Safety and warnings
Important safety precautions
This appliance is not intended for use by young children or infirm persons without
adequate supervision.
Young children should be supervised to ensure that they do not play with the appliance.
In the event this appliance needs repair, please refer to an authorised service agent. Other than
light bulbs and filters, there are no user serviceable parts inside this device. The supply cord, if
damaged, must be replaced by the manufacturer, an authorised service agent or
qualified person.
There is a risk of fire if the appliance is not cleaned.
Don’t flambé under the range hood.
The appliance’s main plug or an isolating switch must be accessible after installation.
Model
HC60PCIX1 & HC90PCIX1
Voltage
220-240V AC / 50Hz
Rated Motor Input Power
198W
Lumination
Max 60W
Rated Input Power
260W
Noise Level
≤65Dba
Extraction Capacity
840±60m³/hr
Outlet Diameter
150mm
WARNING!
Electrical Shock Hazard
Improper use of the grounding plug can result in a risk of electric shock.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
Installation instructions
3
Specifications
Installation height requirements
Where an electric cooktop is installed under this rangehood, the minimum distance
between the top of the cooktop and the underside of the rangehood must be 60cm and
the maximum 70cm.
Where a gas fuelled cooktop is installed under this rangehood, the minimum distance between
the top of the pot rests and the underside of the hood, must be 65cm and the maximum 75cm.
Please note:
Your relevant gas authority may specify different height requirements. Care should be taken to
comply with any applicable regulations concerning the discharge of exhaust air.
Other installation requirements
The air collected must not be conveyed into a duct used to blow off smoke from appliances
fed with an energy other than electricity (central heating systems, thermosiphons, water
heaters etc).
Comply with the official instructions provided by the competent authorities in merit when
installing the disposal duct. In addition, exhaust air should not be discharged into a wall or
ceiling cavity, unless the cavity is designed for that purpose.
Flame/fire retardant materials must be used for all ducting. Self extinguishing VO plastics
are recommended.
The room must be well aerated in case the rangehood and some other heat equipment fed with
an energy other than electricity (gas, oil, coal heaters etc) operate at the same time.
The hood, while disposing of air, could create a vacuum in the room. The vacuum should not
exceed 0.04 mbar. This prevents the gas exhausted by the heat source from being taken in again.
It is therefore advisable to ensure the room contains air gaps able to ensure a steady flow of
fresh air.
Installation options
All Fisher & Paykel canopy range hoods are designed to be ducted to the atmosphere, however
selected models can also be set up to recirculate the extracted air inside your kitchen.
External ducting option
Rangehoods ducted to the outside atmosphere draw air from the kitchen and force it outside
using flame proof ducting (not supplied) as shown in Fig. 1. When installed as a ducted hood
(Fig. 1) an exhaust duct conveys the steam and cooking odours directly outside through the
installed ducting exiting through either the wall or ceiling. Therefore this type of installation
does not require charcoal filters.
4
Installation instructions
Internal recirculation option
Recirculating hoods draw air from the kitchen and purify it using charcoal filters and return the
air back to the kitchen through gaps in the flue, as shown in Fig. 2. When using hoods in the
recirculating option, charcoal filters must be used. These can be purchased through your retailer
or through an authorised service centre.
Fig.1 External ducting
Fig.2 Internal recirculation
Installation process
Please note: If you wish to have the flue run all the way to the ceiling, please ensure that you
work your measurements out fully before attempting the installation. In some instances, extra
lengths of flue or a customised flue maybe required.
1
Establish the desired height of the rangehood above the benchtop according to the ‘Installation
height requirements’ above. Measure this distance from the top of the benchtop and, using a
spirit level, draw a light horizontal line on the wall. Make sure that the line can easily be erased
or will be hidden after installation. This is where the bottom of the rangehood will sit (Fig.3).
60 – 75 cm
Fig.3 Establishing height of rangehood
Installation instructions
2
3
4
5
Mark the position of the rangehood on
the wall. Using a spirit level, also mark a
vertical line intersecting the horizontal
line, (ensuring that the line can easily be
erased or will be hidden after installation)
showing the position where the centre of
the rangehood will be. This is normally over
the centre of the cooktop (Fig. 4).
Remove the grease filters (this is to make
installation easier). Press inward on the
clamp at the handle and pull the filter
downward (Fig. 5).
Determine location of the fixing “keyholes”
on the wall. When the flue is removed,
you will notice that the hood is secured to
the wall by two “keyholes” located above
the motor behind the air exit opening.
From the point where the horizontal and
vertical lines drawn earlier intercept, use
a spirit level and pencil and draw another
horizontal line 290mm above the first
horizontal line (ensuring that the line can
easily be erased or the line will be hidden
after installation) as shown in Fig 6. This
now indicates where the top of the “fixing
keyholes” are.
Where the vertical line meets the top
horizontal line (just drawn), measure and
mark both sides of the vertical line, showing
where to drill.
5
Rangehood Centre
Bottom of Rangehood
Benchtop
Fig.4 Marking the position of the rangehood on the wall
Fig.5 Removing the grease filters
290 mm
Drill holes and secure rangehood to the
wall. Depending on the wall type (concrete,
drywall etc) drill/screw appropriate fittings
in the two locations just marked. The
rangehood should now be able to be hung
on these bolts/screws through the two
keyholes in the hood.
Fig.6 Determining location of the two fixing “keyholes”
6
6
7
Installation instructions
Create additional means of attachment.
Keyholes alone are insufficient means of
attachment. Drill two extra holes in the
back panel, put screws in with an anchor (if
required) to ensure proper attachment and
fix the rangehood by these screws as well, as
shown in Fig. 7. Ensure all fixings are secure.
Assemble and fit ducting. If you choose the
external ducting installation option (Fig.1),
fit the ducting as per the manufacturer’s
instructions. Make sure that the diameter
of the exit opening on the rangehood is
150mm.
Keyholes
Extra
fitting
holes
Fig.7 Creating additional means of attachment
Optional: If desired, the one-way butterfly
valve can now be fitted to the exit opening of the rangehood by simply snapping the two pieces
into place.
8
Test the operation of the rangehood. Plug the rangehood in and test its operation on all speed
levels. This will ensure that any imperfections in the installation, such as unwanted sounds or lack
of suction can be addressed before the flue is in place. Over 95% of service calls are a result of
faulty installation. Please be aware that in the event of a service call for a faulty installation, you
will be charged as this is not covered under the manufacturer’s warranty.
9
Position and secure the flue. Secure the top mounting bracket at the highest possible point on the
ceiling using a single screw through the supplied bracket.
Ensure all ducting and electrical connections are secured correctly and switched on. Place the
bottom part of the flue onto the rangehood and slide the upper part into the lower part so the
tabs “hug” the folded edge of the flue.
Raise the upper part of the flue to the required height and using the four screws supplied, secure
the upper flue to the bracket on the wall.
Installation is now complete.
Using your rangehood
Fig.8 Slide control
3 = Fan On / High
2 = Fan On / Medium
1 = Fan On / Low
0 = Fan Off
1 = Lights On
0 = Lights Off
7
8
Care and cleaning
Cleaning the anti-grease filters
Make sure that you periodically clean the anti-grease filters (at least once every six months, but
more often if you live in high-humidity and/or coastal areas).
To clean the anti-grease filters, remove them
and wash them either by hand or in the
dishwasher using a neutral detergent.
Replacing the charcoal filters
If your rangehood is installed to recirculate
the extracted air, make sure you periodically
replace the charcoal filters, usually every six
to twelve months depending on how much
you use your rangehood.
Fig.9 Replacing the charcoal filter
Cleaning the grease deposit container
Your Fisher & Paykel rangehood is fitted with a clear container underneath the motor housing.
This is only visible when the grease filters are removed. Over time, oil, fat and grease that is
normally deposited inside the rangehood body is directed into this container for easy cleaning.
This unique design will help ensure your Fisher & Paykel rangehood remains in peak condition by
minimising the amount of fat/grease collected in the motor.
Important!
This container should be cleaned as necessary, usually on an annual basis.
Always ensure the container is in place when the rangehood is in operation.
DO NOT ATTEMPT TO BLOCK THE HOLE.
Manufacturer’s warranty
9
When you purchase any new Fisher & Paykel rangehood you automatically receive a two year
Manufacturer’s Warranty covering parts and labour for servicing.
Fisher & Paykel undertakes to
Repair or, at its option, replace without cost to the owner either for material or labour any part of
the Product, the serial number of which appears on the Product, which is found to be defective
within TWO YEARS from the date of purchase.
This warranty DOES NOT Cover
A Service calls which are not related to any defect in the Product. The cost of a service call will be
charged if the problem is not found to be a Product related fault. For example:
1. Correct the installation of the product.
2. Instruct you how to use the product.
3. Replace house fuses or correct house wiring.
4. Correcting fault(s) caused by the user.
5. Noise or vibration that is considered normal, eg. fan sounds, regeneration noises or user
warning beeps.
6. Correcting damage caused by pests, eg. rats, cockroaches etc.
B Defects caused by factors other than:
1. Normal domestic use or
2. Use in accordance with the Product’s User Guide.
C Defects to the Product caused by accident, neglect, misuse or ‘Act of God’.
D The cost of repairs carried out by non-authorised repairers or the cost of correcting such
unauthorised repairs.
E Normal recommended maintenance as set out in the Product’s User Guide.
F Repairs when the appliance has been dismantled, repaired or serviced by other than a
Fisher & Paykel AUTHORISED CUSTOMER SERVICE CENTRE or the selling dealer.
G Pick up and delivery.
H Transportation or travelling costs involved in the repair when the product is installed outside the
Fisher & Paykel AUTHORISED CUSTOMER SERVICE CENTRE’S normal service area.
Service under this manufacturer’s warranty must be provided by an Authorised Service Agent
(refer to the Customer care section for contact details). Such service shall be provided during
normal business hours. This warranty certificate should be shown when making any claim.
Note:
This Warranty is an extra benefit and does not affect your legal rights and applies only to product
purchased in New Zealand and Australia.
Please keep this User Guide in a safe place.
Do not return to Fisher & Paykel.
10
Customer care
Check the things you can do yourself.
Refer to your User Guide and check:
1
2
your appliance is correctly installed
you are familiar with its normal operation
If after checking these points you still need assistance, please refer to the following:
In New Zealand if you need assistance...*
Call your Fisher & Paykel retailer who is trained to provide information on your appliance, or if we
can be of any further help, please contact our Customer Care Centre,
Toll Free: 0800 FP CARE or 0800 37 22 73
Fax: (09) 273 0656
Email: [email protected]
Postal address: P.O. Box 58732 , Greenmount, Auckland
If you need service...*
Fisher & Paykel has a network of independent Fisher & Paykel Authorised Service Centres whose
fully trained technicians can carry out any service necessary on your appliance. Your dealer or
our Customer Care Centre can recommend an Authorised Service Centre in your area.
In Australia if you need assistance...*
Call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care Consultants.
Toll Free: 13 00 650 590
Fax: (07) 3826 9298
Email: [email protected]
Postal Address: PO Box 798, Cleveland QLD 4163
If you need service...*
Fisher & Paykel Australia Pty Ltd has a network of independent Fisher & Paykel Authorised
Service Centres whose fully trained technicians can carry out any service necessary on your
appliance. Our Customer Care Centre can recommend an Authorised Service Centre in your area.
*If you call or write, please provide: name, address, model number, serial number, date of
purchase and a description of the problem. This information is needed in order to better respond
to your request for assistance.
Product Details
Fisher & Paykel Appliances Ltd
Model/Serial No.
Date of Purchase
Purchaser
Dealer
Suburb
Town
Country
Copyright © Fisher & Paykel 2008. All rights reserved.
The product specifications in this booklet apply to
the specific products and models described at the
date of issue. Under our policy of continuous product
improvement, these specifications may change at any
time. You should therefore check with your Dealer to
ensure this booklet correctly describes the product
currently available.
www.fisherpaykel.com
NZ AU
Canopy rangehood installation instructions
and user guide
Published: 03/2008
Part No. 599516 A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement