Elba HP60ICSXW1 Rangehood User Guide

Elba HP60ICSXW1 Rangehood User Guide
Power Pack rangehood
HP60ICSXW1 & HP90ICSXW2 models
Installation instructions
and User guide
Safety and warnings
Installation instructions
Using your rangehood
Accessories and ratings
Manufacturer’s Warranty
Customer Care
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please visit our local website listed on the back cover
or contact your local Fisher & Paykel dealer.
Safety and warnings
Please read the entire instructions before installing the rangehood.
Always switch power off prior to installation.
Stainless steel is very easily damaged during installation if abraded or knocked by tools.
Protect the rangehood with the cardboard box or plastic bag during installation.
All electrical work must be done in accordance with local and national electrical codes
as applicable.
For safety, this product must be earthed.
A power outlet should be within 1500mm of the power cord exit from the rangehood.
The power socket must be accessible and enable the end user to isolate the rangehood from the
power for the purpose of internal cleaning or maintenance.
150mm and 120mm round ducting adapters are supplied. All other ducting accessories are not
supplied. All ducting must comply with local requirements and building codes.
See Ducting options on page 4.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Young children should be supervised to ensure that they do not play with the appliance.
There shall be adequate ventilation of the room when the rangehood is used at the same time as
appliances burning gas or other fuels.
You must read the details concerning the method and frequency of cleaning.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Do not flambé under the rangehood.
Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from
appliances burning gas or other fuels.
The minimum distance between the hob surface and the lowest part of the rangehood is
600mm. This distance shall be at least 650mm, if the rangehood is installed over a gas hob. If the
instructions for the gas hob specify a greater distance, this has to be taken into account.
Attention should be given to ensure that any applicable regulations concerning the discharge of
exhaust air is fulfilled.
If the supply cord of this equipment is damaged, it must only be replaced by the manufacturer or
its service agent or a similarly qualified person in order to avoid a hazard.
Installation instructions
Contents of packaging
1 x Rangehood body
2 x Face plates
1 x 150mm ducting adaptor
1 x 120mm ducting adaptor
1 x Packet of fasteners and wall plugs
Typical equipment required:
Electric drill
Tape measure
Spirit level
Duct tape (if ducting)
Jig saw (if ducting)
Ladder (if ducting)
l Ø120
270 (600
445 (900
490 (600
665 (900
520 (600
696 (900
Fig 1. Ducting dimensions
270 (600)
445 (900)
520 (600)
696 (900)
Fig 2. Power Pack dimensions
Note: All dimensions are in millimetres.
HP60ICSXW1 is a 600mm unit, and HP90ICSXW2 is a 900mm unit.
Installation instructions
Ducting options
The method of ducting should be carefully considered before installing the rangehood. The guide
below recommends the ducting components to use for all common ducting configurations through the top of the home (for the roof and soffit) and through the rear of the home. 150mm
round ducting should be used in conjunction with this model rangehood. Alternatively this
rangehood can be operated in recirculation mode (see Recirculation mode pg. 6).
Top ducting through roof
Side ducting
(use Charcoal Filter Discs mounted
either side onto the Motor)
Fig 3. Ducting options
It is recommended that Ø150mm ducting is to be used, however a reducer from Ø150mm
to Ø120mm is included with the rangehood should the Ø120 ducting be required.
Extra lengths and/or bends may be required, depending on the length required and whether there
is any structural material in the run, eg. rafters.
Opening to
suit models
Some authorities require rangehoods
to be vented outside. Ducted models should comply with
this requirement in every respect.
Please note that this chart is designed as a guide. Please consult Fisher & Paykel Customer Care
if unsure. For New Zealand please phone 0800 FP CARE or 0800 37 2273. And in Australia please
phone 1 300 650 590.
For Gas 650-800
Face Plate
Mounting holes
either side onto the Motor)
Installation instructions
Installation position
When installing the rangehood, the lower edge of the unit must be a minimum of 600mm
(650mm for gas cooker) above the cooking range. The recommended position for the hood is
650mm above the hotplates.
Opening to
suit models
For Gas 650-800
Face Plate
Fig 4. Minimum height from the hob surface to the underside face
of the rangehood is: 600mm for electric hob, 650mm for gas hob
Note: If the instructions for the gas hob specify a greater distance, this has to be taken into
account. Any installation above 750mm will compromise performance.
Installation instructions
Mounting the rangehood
Fit the ducting adaptor to the rangehood using the short screws supplied.
Provide an opening
on thethrough
Top ducting
roof of the cupboard to suit models: provide 490mm x 258mm
Side ducting
(use Charcoal Filter Disc
for 600 model or 665mm x 258mm for 900 model.
either side onto the
Remove the face plate of the rangehood by undoing the two visible screws located on both sideends. Eight mounting holes around the unit then are accessible.
Lift the rangehood and fit through the opening of the cupboard. Secure unit using long screws
supplied. Refit face plate.
Opening to
suit models
For Gas 650-800
Fig 5. Installation of unit
(NZ model may vary slightly from images)
Face Plate
Mounting holes
Recirculation mode
This unit can be installed to operate in recirculation mode where ducting is not a chosen/
desired or practical option. Ensure that the top ducting outlet are not obstructed. Even a partial
obstruction will restrict the efficiency of the rangehood.
Replace aluminium filters with charcoal filters (Part & Accessories list on pg. 8).
Using your rangehood
The light can be operated independently by sliding the light switch on/off despite the working
status of the fan. Please refer to the icon on switch panel.
The fan is operated by sliding the power switch on. It can be run at three different speeds (Speed
1 / Speed 2 / Speed 3) depending on the cooking requirements. Please refer to the icon on switch
General maintenance
Switch off the rangehood before cleaning or maintenance. To prevent surface damage never use
abrasive or oil based liquid cleaners. To clean the surfaces of the appliance, use mild detergent
and warm water. In areas of high humidity and coastal environments cleaning should be carried
out frequently.
A build up of oil may occur if the rangehood is not cleaned regularly.
Filter Maintenance
To maintain efficiency, the filters should be removed regularly (approximately monthly), and
washed using hot soapy water or the dishwasher.
Note: some discolouration of the frame may occur if washed in the dishwasher.
Rangehoods fitted with charcoal filters are designed to remove grease and odours from cooking
vapours prior to the cleansed air re-entering the kitchen (when the rangehood is in recirculation
mode). Charcoal filters should be replaced every two to four months depending on use.
Note: Fully saturated charcoal filters can become a barrier to air movement therefore limiting
rangehood performance. In the event of fire, grease laden filters could be flammable and
therefore regular replacement is recommended. In ducted installations, conventional aluminium
filters are recommended.
Replacement of incandescent bulbs
To replace a bulb, first disconnect the rangehood from the power supply. Use a small blade
screwdriver to prise off the lamp cover. Care must be taken to avoid the lamp lens falling on to
the hob top. The bulb is a screw fit into the lamp socket. Insert the replacement bulb into the
lamp socket and replace the lamp cover.
Note: replacement bulbs are not covered by warranty.
Accessories and ratings
Parts and accessories list
Charcoal filter (600 model)
Charcoal filter (900 model)
Incandescent bulb
Product approvals and ratings
Product approval number
Product rating
Electric approval AS/NZS
Performance tested
290W (1.21A) MAX at240V 50Hz
Manufacturer’s Warranty
You automatically receive a 2 year Manufacturer’s Warranty with the purchase of this
Product covering parts and labour for servicing within the country of purchase.
Fisher & Paykel undertakes to:
Repair or, at its option, replace without cost to the owner either for material or labour any
part of the Product, the serial number of which appears on the Product, which is found to
be defective within TWO YEARS of the date of purchase.
Note: this Warranty is an extra benefit and does not affect your legal rights.
This Warranty DOES NOT cover
Service calls which are not related to any defect in the Product. The cost of a service call will be
charged if the problem is not found to be a Product fault. For example:
1. Correcting the installation of the Product.
2. Instructing you how to use the Product.
3. Replacing house fuses or correcting house wiring or plumbing.
4. Correcting fault(s) caused by the user.
Noise or vibration that is considered normal, eg drain/fan sounds, refrigeration noises
or user warning beeps.
6. Correcting damage caused by pests, eg rats, cockroaches, etc.
7. Replacement light bulbs.
Defects caused by factors other than:
1. Normal domestic use or
2. Use in accordance with the Product’s User Guide.
Defects to the Product caused by accident, neglect, misuse or Act of God.
The cost of repairs carried out by non-authorised repairers or the cost of correcting such
unauthorised repairs.
Normal recommended maintenance as set out in the Product’s User Guide.
Repairs when the appliance has been dismantled, repaired or serviced by other than a
Fisher & Paykel Authorised Repairer or the selling dealer.
Pick-up and delivery.
Transportation or travelling costs involved in the repair when the Product is installed outside the
Fisher & Paykel Authorised Repairer’s normal service area.
This Product has been designed for use in a normal domestic (residential) environment. This
Product is not designed for commercial use (whatsoever). Any commercial use by a Customer will
affect this Product’s Warranty.
Service under this Manufacturer’s Warranty must be provided by a Fisher & Paykel Authorised Repairer
(refer to the ‘Customer Care’ section at the back of this book). Such service shall be provided during
normal business hours. This Warranty certificate should be shown when making any claim.
For Australian Customers
This Warranty is an extra benefit and does not affect your legal rights. Our goods come with
guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Please keep this User Guide in a safe place.
Customer Care
Before you call for service or assistance…
Check the things you can do yourself.
Refer to your User Guide and check:
Your appliance is correctly installed
You are familiar with its normal operation
If after checking these points you still need assistance, please refer to your nearest Fisher & Paykel
Authorised Repairer, or contact us through our local website listed on the back cover.
In New Zealand if you need assistance...*
Call your Fisher & Paykel retailer who is trained to provide information on your appliance, or if we
can be of any further help, please contact our Customer Care Centre,
Toll Free: 0800 FP CARE or 0800 37 2273 Fax: (09) 273 0656
Email: [email protected]
Postal address: PO Box 58732, Botany, Manukau 2163
If you need service...*
Fisher & Paykel has a network of independent Fisher & Paykel Authorised Repairers whose fully
trained technicians can carry out any service necessary on your appliance. Your dealer or our
Customer Care Centre can recommend a Fisher & Paykel Authorised Repairer in your area.
In Australia if you need assistance...*
Call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care Consultants.
Toll Free: 1 300 650 590
Fax: (07) 3826 9298
Email: [email protected]
Postal Address: PO Box 798, Cleveland QLD 4163
If you need service...*
Fisher & Paykel has a network of qualified Fisher & Paykel Authorised Repairers responsible for
servicing only Fisher & Paykel branded appliances. Our Customer Care Centre can recommend a
qualified Fisher & Paykel Authorised Repairer in your area.
*If you call, write or contact our website please provide: your name and address, model number,
serial number, date of purchase and a complete description of the problem. This information is
needed in order to better respond to your request for assistance.
Product details
Fisher & Paykel Appliances, Ltd
Model/Serial No.
Date of Purchase
Copyright © Fisher & Paykel 2011. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
F&P PN - 791538 B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF