Micronet SP668C EtherFast Gigabit Switch Manual

Add to my manuals
8 Pages

advertisement

Micronet SP668C EtherFast Gigabit Switch Manual | Manualzz

Quick Installation Guide

EtherFast Gigabit Switch

Model No.: SP668C http://www.micronet.info

Introduction

This switch provides 8 Gigabit Ethernet ports to offer an economical way for the SOHO and small to medium business users to benefit from the increased bandwidth. It upgrades your desktops to Gigabit connections has never been cost-effective. Also, it is perfect for graphics, multimedia, and other applications that have to move large files across the network quickly.

With its intelligent addressing engine, it provides users with a wire-speed filtering and forwarding of the traffic. All ports support auto-uplink detection, so users don't have to worry about the cable type. Each port will automatically communicate for best speed and to run in half- or full-duplex mode. Store-and-forward switching prevents damaged packets and network errors from being passed on into the network.

1

Package Contents

Before you start installing the device, verify the following items are in the package: y Gigabit Ethernet Switch y Quick installation guide y Screws and wall-mount kit y Power adapter

Features

y Complies with 10Base-T/100Base-TX/1000Base-T specifications of the IEEE802.3/802.3u/802.3ab standard y Support auto-negotiation function to automatically select optimal speed (10/100/1000M) and mode (full/half duplex) y Support 802.3x flow control for full-duplex mode and back-pressure flow control for half-duplex mode y 8K MAC address entries y 144K bytes memory buffer y Support jumbo frame up to 9000 bytes y Support auto uplink, no more cross-over cable y Forward and filter packets at non-blocking, full wire speed

2

Physical Description

Front view

Rear view

Please refer to the following table for LED definition

LED Status Operation

Power

Steady Green

Off

1000M

100M

Steady Green

Steady Green

Power is on

Power is off

1000M network connection established

100M network connection established

10M/ACT

Steady Green

Blinking Green

10M network connection established

Transmitting or receiving data

3

Installation

This switch does not require software configuration. Users can immediately use any of the features of this product simply by attaching the cables and turning on the power.

Connect each station to the switch by twisted-pair cable. Plug one

RJ-45 connector into a RJ-45 port of the switch, and plug the other

RJ-45 connector into the station’s network adapter. Power on the switch and then system is ready.

In making a switch interconnection, you could use any port to connect another switch with straight or crossover cable. As all the ports support auto-uplink (MDI / MDI-X) function, using a straight cable to make a switch-to-switch connection is allowed.

For cable selection, refer to the following table

Network Speed Cable Type Max. Length

10M

100M

Cat. 3, 4, 5 UTP/STP

Cat. 5 UTP/STP

100 meters

100 meters

1000M Cat. 5, 5e UTP/STP 100 meters

Note: To prevent costly equipment damage and downtime, please consider installing a surge suppression device or a UPS

(Un-interrupted Power Supply).

4

Specifications

Standard

Interface

Cable Connections

Network Speed

IEEE802.3, IEEE802.3u, IEEE802.3ab

IEEE802.3x flow control

8 * RJ-45 ports (10/100/1000M)

10BASE-T: Category 3, 4, 5 UTP/STP

100BASE-TX: Category 5 UTP/STP

1000BASE-T: Category 5, 5e UTP/STP

10/100/1000M & full/half duplex mode auto detection (1000M for full duplex only)

Auto-uplink (Auto MDI / MDI-X)

16.0Gbps

144K bytes

Uplink

Switch Fabric

Memory

MAC Address Table

Jumbo Frame

Filtering/Forwarding

Rate

8K entries

9000 bytes

10M: 14,880pps/14,880pps

100M: 148,800pps/148,800pps

1000M: 1,488,100pps

Emission FCC, CE

Operating Temperature 0

o

~ 50

o

C (32

o

~ 122 o

F)

Operating Humidity 10% ~ 90% (Non-condensing)

Dimension

Power Supply

146 x 117 x 30 mm

External power adapter

12V DC 1.0A

5

CE Mark Warning

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date.

Please check with your local distributors for the latest information.

No part of this document can be copied or reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Copyright © 2005, All Rights Reserved.

6

7

P/N: 2300-0340

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement