Motorized Recovery

Exerciser

4108.1-042220

IMPORTANT: Read all instructions carefully before using this product.

Retain this owner’s manual for future reference.

The specifications of this product may vary from this photo, subject to change without notice.

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.

STOP. Contact customer service if you have any questions regarding assembly or proper operation of the machine.

Email us at:

[email protected]

TABLE OF CONTENT

SERVICE ------------------------------------------------------------------------ 2

LABEL PLACEMENT --------------------------------------------------------- 3

IMPORTANT SAFETY GUIDELINES ------------------------------------- 4

OVERVIEW DRAWING ---------------------------------------------------- 6

PARTS LIST --------------------------------------------------------------------- 7

HARDWARE PACK------------------------------------------------------------ 9

ASSEMBLY---------------------------------------------------------------------- 10

CONSOLE-------------------------------------------------------------------- 16

ADJUSTMENTS-------------------------------------------------------------- 17

TRANSPORTING------------------------------------------------------------ 20

WARRANTY------------------------------------------------------------------- 21

PARTS REQUEST FORM--------------------------------------------------- 22

1

SERVICE

IMPORTANT: FOR NORTH AMERICA ONLY

For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods:

For The Best Service, please Email: [email protected]

Response Time: 1-2 Business Days

Emailing us with the information above will be the best method to receive a response during peak business hours

Website: www.paradigmhw.com

Toll-Free:

1-844-641-7921

(8:00 AM - 5:00 PM Pacific Standard Time, Monday thru Friday)

Response time may vary via calling





Please have the following information ready when requesting for service:



Your name



Phone number



Model number



Serial number

Part number

Proof of Purchase

For damaged or defective product please contact our customer service before returning to the store.

Paradigm Health & Wellness, Inc.

1189 Jellick Ave.

City of Industry, CA 91748, USA

2

LABEL PLACEMENT

3

IMPORTANT SAFETY GUIDELINES

Read all instructions before using the equipment. When using the equipment, basic precautions should always be followed.

WARNING - To reduce the risk of injury to persons, read and understand the following:

1. Make sure machine is correctly assembled before you use it.

2. Be sure all screws, nuts, and bolts are tightened prior to use.

3. Before using machine, we recommend doing warm ups and stretching of the major muscle groups.

4. Only one person should be using machine at a time.

5. Never operate machine if it is damaged, if it is not working properly, has been dropped, or damaged. If a problem is encountered contact Customer Service before using the equipment again.

6. Always use machine on a clear and level surface.

7. For household use only.

8. Do not use outdoors or near water.

9. Use machine only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

10. Do not wear loose clothing when using the equipment.

11. Never drop or insert any object into any opening.

12. If at any time you feel faint, light-headed, or dizziness while operating the equipment, stop exercising immediately. You should also stop exercising if you are experiencing pain or any discomfort.

13. For any problems contact customer service. Servicing should be performed by an authorized service representative. Our contact number is on the service page.

14. Set up machine as directed in Set Up instructions and place unit on level, non-slip surface.

15. Do not stand on the machine, only exercise in seated position.

16. Keep a minimum safety clearance during operation. The machine is designed as a home use exercise device. User must have full control of their muscles to operate this unit. It may not be suitable for people who are quadriplegic or paraplegic.

Please consult your doctor or physician.

17. Keep a minimum safety clearance during operation. The machine is designed as a home use exercise device. User must have full control of their muscles to operate this unit. It may not be suitable for people who are quadriplegic or paraplegic.

Please consult your doctor or physician.

18. Exercise equipment is to be regularly inspected for maintenance for loose or broken parts.

19. DO NOT pedal in reverse.

20. This product requires a minimum of 6 square feet of space for safe operation.

21. ASSEMBLE ALL PARTS AND HARDWARE IN THE ORDER THAT IS SHOWN IN THE

ILLUSTRATIONS

22.

Warning:

- Risk of Personal Injury - Consult with your personal physician to see if this exercise equipment is appropriate for you. This is especially important for people with pre-existing health problems. Do not use this equipment without your physician's approval.

23.

Warning:

- Risk of Personal Injury – Do not allow children to use this machine.

24.

Warning:

- Risk of Personal Injury - Keep children under the age of 13 away from the machine.

4

IMPORTANT SAFETY GUIDELINES

25.

Warning:

- Risk of Personal Injury

– Keep body parts, hair, loose clothing, and jewelry clear of all moving parts.

26.

Warning:

- Risk of Personal Injury Do not attempt to service the unit yourself.

Discontinue use and contact customer service.

27.

Warning :

- To Reduce The Risk Of Personal Injury - Read And Understand All The

Instructions Before Using the Bike.

Do not use this equipment if you have any of the following conditions or ailments:



Pregnancy



Extreme obesity



Middle ear infection



Hiatus hernia or Ventral hernia



Glaucoma, retinal detachment or conjunctivitis



Use of anticoagulants including Aspirin in high doses.



Spinal injury, Cerebral Sclerosis, or acutely swollen joints



Heart or circulatory disorders for which you are being treated



High blood pressure, Hypertension, Recent stroke or Transient Ischemic attack



Bone weaknesses including Osteoporosis, Unhealed fractures, Modular pins, or surgically implanted orthopedic supports.

Retain this owner’s manual and keep the original purchase receipt for future reference.

SAVE THESE GUIDELINES

5

OVERVIEW DRAWING

6

No. Description

1 Right Handle

2 Left Handle

3 Front Stabilizer

4 Console

5 Pedal Bracket

6 Support Tube

7 Gas Spring

8 Main Frame

9 Adjustable Tube

10 Left Pedal Crank 5"

11 Right Pedal Crank 5"

12 Right Handlebar Crank 4"

13 Left Handlebar Crank 4"

14 Axle

15 Crank Cap

16 Crank Cover

17 Left Cover

18 Right Cover

19 Small Right Cover

20 Small Left Cover

21 Rear Foot Pad

22 Block

23 Speed Sensor Wheel

24 Buffer

25 Console Board

26 Spring Knob

27 Right Pedal

28 Left Pedal

29 Clip

30 Motor

PARTS LIST

1

2

1

1

3

1

1

1

1

1

1

1

4

2

1

1

Qty No.

1

1

1

31 Plate

Description

32 Control Board

33 Magnet Ring

1

1

1

1

34

35

36

37

Optical Sensor

Power Switch

Crank Cover

Nylon Strap

1

1

1

1

2

4

2

38

39

40

41

42

43

44

45

46

47

48

Hex Nut M8

Hex Nut 9/16-18L

Hex Nut 9/16-18R

Cap Nut M8

Phillips Screw M5x6

Phillips Screw M5x10

Hex Bolt M8x15

Hex Bolt M8x30

Hex Bolt M8x35

Phillips Screw M5x10

Phillips Screw M6x12

49 Self-Tapping Screw ST2.9x6.0

50 Self-Tapping Screw ST2.9x10.0

51 Self-Tapping Screw ST4.2x15.0

52

Flat Head Self-Tapping Screw

ST4.2x15.0

53

54

Self-Tapping Screw with Flat Washer

ST2.5x6.5

Self-Tapping Screw with Flat Washer

ST2.9x9.5

55 Flat Washer Φ5.1*Φ10.3*T0.8

56 Flat Washer Φ8.5*Φ16.0*T1.5

57 Spring Washer Φ6.1*Φ9.3*T1.6

58 Spring Washer Φ8.4*Φ13.5*T2.5

59

Curved Washer

Φ8.4*Φ19.0*T1.5*R20.0

60

Internal tooth lock washer

Φ5.3*Φ10.0*0.6T

Qty

6

2

1

2

1

1

2

12

2

1

4

2

1

2

2

1

2

1

2

1

1

1

1

4

6

8

1

1

4

14

7

No. Description

61 Carriage Bolt M8x65

62 Flange Bolt M8x20

63 Upper Sensor Wire

64 Upper Power Cord

65 Lower Sensor Wire

PARTS LIST

Qty No.

2

4

1

66

67

Description

Lower Power Cord

5mm Allen Wrench with Phillilps

Screwdriver

68 S13-S15 Open Wrench

1

1

69 S17-S19 Open Wrench

Qty

1

1

1

1

8

HARDWARE PACK

9

ASSEMBLY

Tool:

13-15mm Open Wrench 1PC

Step 1

1A. Installing the Front Stabilizer

Attach the Front Stabilizer (3) onto the Main Frame (8), and tighten with two Carriage

Bolts (61), two Curved Washers (59) and two Cap Nuts (41) by using S13-15 Open

Wrench provided.

Hardware:

(61) Carriage Bolt

2PCS

(41) Cap Nut

2PCS

(59) Curved Washer

2PCS

10

ASSEMBLY

Tool:

13-15mm Open Wrench 1PC

5mm Allen Wrench with Phillips

Screwdriver 1PC

Step 2

2A. Installing the Gas Spring

Attach the Gas Spring (7) on to the Support Tube (6) & Main Frame (8), and tighten with one Hex Bolt (45) , one Hex Bolt (46) and two Hex Nuts (38) by using S13-15 Open

Wrench and 5mm Allen Wrench with Phillips Screwdriver provided.

NOTE* install the Gas Spring (7) with the handle on the Support Tube (6). Be sure Not to drop the Support Tube (6), Hold it secure during installation.

Hardware:

(46) Hex Bolt

1PC

(45) Hex Bolt

1PC

(38) Hex Nut

2PCS

11

ASSEMBLY

Step 3

3A. Installing the Pedal Bracket

Insert the Pedal Bracket (5) onto the Main Frame (8) , and tighten with one Spring Knob (26).

Tool:

5mm Allen Wrench with Phillips

Screwdriver 1PC

Hardware:

(48) Phillips Screw

3B. Installing the Rear Foot Pad

2PCS

Gently lay down the machine on the floor and insert the Rear Foot Pad (21) onto the Main Frame

(8) , and tighten with two Phillips Screws (48) by using 5mm Allen Wrench with Phillips

Screwdriver provided.

12

ASSEMBLY

Tool:

Step 4

4A. Installing the Left Handlebar

13-15mm Open Wrench 1PC

Attach the Left Handlebar (2) onto the Left Handlebar Crank (13), turn the Handlebar shaft by hand in a COUNTER-CLOCKWISE direction until snug. Tighten the shaft in a

COUNTER-CLOCKWISE Direction using the 13-15mm Open Wrench provided.

4B. Installing the Right Handlebar

Attach the Right Handlebar (1) onto the Right Handlebar Crank (12), turn the Handlebar shaft by hand in a CLOCKWISE direction until snug. Tighten the shaft in a CLOCKWISE Direction using the 13-15mm Open Wrench provided.

13

ASSEMBLY

Tool:

13-15mm Open Wrench 1PC

17-19mm Open Wrench 1PC

Step 5

Tip: Only turn the pedals in direction instructed. The left, right pedals and left, right pedal nuts will have different directions for installation. The Cranks, Pedals, Pedal Shafts, Pedal

Nuts, and Pedal Straps are marked “R” for Right and “L” for Left

5A. Removal of Hardware : Remove the Left Pedal Nut (39) and Right Pedal Nut (40) from the

Left and Right Pedal (28, 27). DO NOT MIX UP THE PEDAL NUTS.

5B. Installing the Left Pedal onto the Left Pedal Crank: Insert the Left Pedal (28) perfectly straight into the threaded hole in the Left Pedal Crank (10) . Turn the Pedal shaft by hand in a

COUNTER-CLOCKWISE direction until snug. Use the S13-15mm Open Wrench to tighten the

Left Pedal (28) until the shaft protrudes through crank. Attach the previously removed Left Pedal

Nut (39) to the protruding shaft in a CLOCKWISE direction. Use both the S17-19mm Open

Wrench and S13-15mm Open Wrench to simultaneously tighten the Left Pedal (28) and the Left

Pedal Nut (39) . Only tighten in the directions instructed.

5C. Installing the Right Pedal onto the Right Pedal Crank: Insert the Right Pedal (27) perfectly straight into the threaded hole in the Right Pedal Crank (11) . Turn the Pedal shaft by hand in a

CLOCKWISE direction until sung. Use the S13-15 Open Wrench to tighten the Right Pedal (27) until the shaft protrudes. Attach the previously removed Right Pedal Nut (40) to the protruding shaft in a COUNTER-CLOCKWISE direction. Use both the S17-19mm Open Wrench and

S13-15mm Open Wrench to simultaneously tighten the Right Pedal (27) and the Right Pedal Nut

(40) . Only tighten in the directions instructed.

14

ASSEMBLY

Step 6

6A. Attaching the Nylon Strap

Attach the Nylon Strap (37) to the Pedal Bracket (5).

15

CONSOLE

DISPLAY FUNCTION:

Scan - Displays each Function for 4 seconds

Level - Shows speed of the pedals and handles.

Time - Counts the time Up or Down.

Count - Accumulation of revolutions of pedals and handles.

RPM - Revolutions per minute of the pedals and handles.

NOTE* Press ‘‘M’’ mode button to cycle through level, time, count and RPM.

MANUAL MODE :

1. Press HAND POWER button or FOOT POWER button to start a

MANUAL session. NOTE* Can do HANDS or FEET one at a time or both at the same time.

2. Control speeds of pedals and handles by clicking the “ + ” to increase or “ – “ Decrease. Speed range is level 1-12.

3. Press the button to change direction of the pedals and handles rotation. NOTE* in MANUAL session will stop when console reaches 30 minutes.

TIMED MODE:

1. Press the “TIME” button to set a timed session. Press the “ + ” to increase or “ – “ to decrease time.

Time range is 1-30 minutes. NOTE*: in timed mode can use all controls like in MANUAL MODE .

PRESETS:

1. The Console has 5 preset sessions that run for 15 minutes. During the 15 minutes the direction of the pedals and handles change forward to backwards.

2. Press the “M” mode button to get into the preset selections. They are designated from P1- P5 .

Press the “ + ” and “ – “ buttons to cycle through the presets. When the desired preset is highlighted press the FOOT POWER button or the HAND POWER button or BOTH to begin the session.

3. The presets are P1- P5 with P1 having the slowest speed. The speed incrementally increases from Level 1-12 between P1- P5 with P5 Having the highest speed.

16

ADJUSTMENTS

Adjusting the Adjustable Tube

Loosen the knob by rotating it Counter-

Clockwise and Pull the Spring Knob (26) out and adjust the Adjustable Tube (9) Up or

Down to the desired height. When desired adjustment is selected rotate the Spring

Knob (26) Clockwise until tight.

NOTE: When adjusting the height of the

Adjustable Tube (9) , make sure the height of the Adjustable Tube (9) does not exceed the MAX line on the Adjustable Tube (9) .

17

Adjusting the Gas Spring

Push down the Knob of the Gas Spring (7) and adjust the Support Tube (6) to the desired height.

ADJUSTMENTS

Adjust for Longer Strap

Hold the Nylon Strap (29) in both hands.

With one hand grip the plastic adjuster and pull toward the end with the looped strap around the clasp hook. Hold the other hand secure. Pull the adjuster until desired length.

Adjust for Shorter Strap

To shorten Nylon Strap (29), hold the top strip of the loop in one hand. With the other hand grab and pull the plastic adjuster away from the loop. Pull the adjust until desired length.

18

ADJUSTMENTS

Secure Chair to Exerciser

Use the Nylon Strap (29) to attach and secure the chair to the exerciser.

This prevents pushing away the exerciser during your workout.

19

TRANSPORTING

Transporting the Ergometer

Hold the Left & Right Handlebar (2) & (1) and till the wheels on the Front Stabilizer (3) make contact with the floor. Push or pull the unit to the desired location, then gently lower the Pedal

Bracket (5) back down to the ground.

20

WARRANTY

MANUFACTURER’S LIMITED WARRANTY

Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operate d in accordance with Paradigm’s Owner’s

Manual. Paradigm’s obligation under this warranty applies to the following:

COMPONENT LENGTH OF WARRANTY

Structural Frame 1 year For Home Use Only

All Other Components 90 days For Home Use Only

(computer display, electronics, upholstery, foam, ball bearings, pulleys, belts, cables, wires, shocks, covers, tension, internal mechanism, wheels, pedals, knobs, accessories and hardware)

Exclusions from Warranty Coverage:

Paradigm does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

1. I mproper installation and/or failure to abide by Paradigm’s installation guidelines;

2. Use of this product beyond normal home use, or in an application for which it was not designed;

3. Cosmetic items such as scratches, dents or discolorations;

4. Damage caused by normal wear and tear, vandalism, accidental or by animals;

5. Any act of Nature (such as fire, flooding, snow, ice, hurricane, earthquake, lightning or other natural disaster), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);

6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to, among other things, flake, chalk, accumulate dirt or stains.

7. Improper operation, alteration, handling, storage, abuse or neglect of the products.

Paradigm, using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of th e original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.

Ordering Replacement Parts

Replacement parts can be ordered by emailing our customer service department:

[email protected]

Open Monday thru Friday 8:00 AM - 5:00 PM (PST).

When ordering replacement parts please have the following information ready:

1. Owner’s Manual

2. Model Number

3. Description of Parts

4. Part Number

5. Date of Purchase

21

PARTS REQUEST FORM

Paradigm Health & Wellness

, Inc.

EMAIL THIS FORM WITH YOUR RECEIPT OF PURCHASE TO

[email protected]

*

NAME: _____________________________________________________________________________________

ADDRESS: __________________________________________________________________________________

CITY: ________________________ STATE: _____________ ZIP: _______________________________________

TELEPHONE: (Day) ______________________________________________________________________

(Night) _____________________________________________________________________

SERIAL#: ___________________________________________________________________________________

MODEL#: ___________________________________________________________________________________

PURCHASE DATE: ___________________________________________________________________________

PLACE OF PURCHASE: _______________________________________________________________________

PART # DESCRIPTION QTY

“YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”

This form can also be faxed to #: 626-810-2166

22