Mircom LT-979 TX3 Programming Manual

Add to my manuals
62 Pages

advertisement

Mircom LT-979 TX3 Programming Manual | Manualzz
TX3 Series
Telephone Access System
Programming Manual
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright November 2019
1
Copyright November 2019 Mircom Inc.
All rights reserved.
Mircom Telephone Access System Programming Manual Version 3.1
Microsoft, MS-DOS, Windows, and Windows 2000/NT/XP/Vista/7/8/10 are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Mircom
25 Interchange Way
Vaughan, Ontario
L4K 5W3
905.660.4655
http://www.mircom.com
2
LT-979
TX3 Telephone Access System Programming Manual
Copyright November 2019
Version 3.1
Contents
1
Introduction 4
1.1
1.2
1.3
1.4
1.5
1.6
TX3 Systems 5
Features 6
Warranty and Special Notices 7
About This Manual 7
Contact Us 8
Viewing Resident List 8
2
Configuration 9
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
Keypad Navigation 10
Beginning Configuration 10
Accessing the Operation Menu 11
Viewing Configuration Information 13
Viewing the Time and Date 14
Configuration Menu 15
System Option 15
Database Menu 32
Schedule Menu 43
Holidays Menu 45
Set Time & Date 46
Factory Default 47
Input/Output 47
Correlations 49
Changing Passcodes 52
Test LCD 53
Warranty and Warning Information 54
Special Notices 59
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
3
1
Introduction
This manual provides you with detailed instructions on how to configure the
TX3 Telephone Access System from the main entry panel keypad.
This manual must be read in its entirety before beginning the configuration.
Configuration must be performed by a qualified technician and must adhere to
the standards and special notices set by the local regulatory bodies.
Note:
Mircom periodically updates panel firmware and
Configurator Software to add features and correct any minor
inconsistencies. For information about the latest firmware or
software visit the Mircom website at www.mircom.com.
For warranty and special notices information see the Warranty and Special
Notices chapter on page 54.
This manual explains
4
LT-979
•
The TX3 Telephone Access System
•
How to configure the TX3 Telephone Access System
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Introduction
1.1
TX3 Systems
The Mircom's TX3 series of telephone access systems provide high quality twoway communication between residents and their visitors in a multi-unit dwelling
establishment.
The basic TX3 system consists of the TX3 Entry Panel and depending on the
application, may be integrated with a combination of Mircom Elevator
Restriction Units and Card Access Units. All access systems may be networked
together using an RS-485 connection.
The TX3 system is capable of providing ADC or NSL telephone access from a
single panel or from a networked system. The TX3 system also may consist of
one or more access systems networked together using an RS-485 connection.
The access system can be configured as an autodialer controller (ADC) or as a no
subscriber line (NSL) system. Both system setups can be configured for multiple
entrances with independent doors and control devices such as electric door locks,
cameras, and garage doors.
1.1.1
ADC and NSL Capability
A single TX3 Entry Panel supports full ADC and NSL telephone connectivity.
An ADC connection requires a dedicated subscriber telephone line service
connected to an outside telephone line. This mode lets the visitor call the tenant
and access their voice mail.
An NSL connection uses the existing building telephone lines for
communication and does not require a separate telephone line. This system may
consist of one or more entry panels connected to TX3-NSL-8M NSL Units,
typically located in the electrical/telephone room of a building. The NSL units
intercept all telephone lines into the building’s suites if the lines are not in use.
This mode lets the visitor call the tenant and access their voice mail and call
waiting.
1.1.2
Elevator Restriction Units
The TX3-ER-8 Elevator Restriction Unit limits building accessibility by
granting visitor access only to the destination floor.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
5
Introduction
1.2
Features
Features of the TX3 series include:
6
LT-979
•
Stainless steel front panel
•
Universal Series enclosure with a built-in rain hood
•
Large scrolling 8 x 20 LCD display that eliminates the need for an external
directory
•
Back-lit 16 digit keypad with dedicated operational buttons for Page Up,
Page Down, Call and Info
•
Provisions for postal lock and camera
•
Multilingual Display and Voice Greeting (English, French-Canadian and
Spanish) that provides instructions on how to use the entry panel
•
Concierge/Security Desk/Guard Phone capability
•
Card Access Interface
•
Supports both Auto Dialer (ADC) and NSL (no phone bill)
•
Ability to network panels together (peer-to-peer)
•
Hands free, full duplex communication
•
Flexible one to four digit resident dial codes
•
Dials up to 18 digit telephone numbers
•
System can be configured locally using the keypad or a computer with the
TX3 configuration software
•
Upload/download configuration files without taking the whole system
off-line
•
Programming from one location
•
Records a maximum of 5000 event logs
•
Elevator restriction capability
•
Schedule based call restrictions provide more security and flexibility
•
Capability of one person testing of the NSL controller without using the
lobby panel
•
Industry Canada and F.C.C. approved
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Introduction
1.3
Warranty and Special Notices
Mircom values your business and always attempts to provide you with the very
best service.
Please see the Warranty and Special Notices chapter on page 54 for information
about the warranty and special notices about equipment use.
1.4
About This Manual
This manual provides comprehensive information on the configuration of the
TX3 Series Telephone Access System. Tasks are described in the order that they
are likely to be performed.
This manual applies to the following models:
1.4.1
•
TX3-120U and TX3-120U-A/C
•
TX3-200-8U, TX3-200-8U-A and TX3-200-8U-B/C
•
TX3-1000-8U, TX3-1000-8U-A and TX3-1000-8U-B/C
•
TX3-2000-8U, TX3-2000-8U-A and TX3-2000-8U-B/C
•
TX3-200-4U-A and TX3-200-4U-B/C
•
TX3-1000-4U-A and TX3-1000-4U-B/C
•
TX3-2000-4U-A and TX3-2000-4U-B/C
•
TX3-120C-A/C
•
TX3-200-8C-A and TX3-200-8C-B/C
•
TX3-1000-8C-A and TX3-1000-8C-B/C
•
TX3-2000-8C-A and TX3-2000-8C-B/C
•
TX3-200-8CH-A, TX3-1000-8CH-A and TX3-2000-8CH-A
•
TX3-200-8UH-A, TX3-1000-8UH-A and TX3-2000-8UH-A
•
TX3-2000-8K-A
Additional Documentation
For additional documentation, see the following Mircom literature:
Version 3.1
LT-979
•
LT-995 TX3-CX Touch Screen Administrators Guide
•
LT-968 TX3 Telephone Access System User’s Guide
TX3 Telephone Access System Programming Manual
Copyright 2019
7
Introduction
1.5
Contact Us
1.5.1
Canada and USA
Phone: 905-660-4655
Toll Free: 1-888-660-4655
Fax: 905-660-4113
1.5.2
International
Phone: 905-660-4655
1.5.3
Website
http://www.mircom.com
1.6
Viewing Resident List
The TX3 Entry Panel LCD shows a scrollable view of the resident names and dial
codes. The LCD comes in a four or eight line LCD handset version. A paper
version of the resident list is also available.
To view the resident list
1.
Press the up or down arrow keys on the Entry Panel keypad to scroll
through the list line by line.
or
To view the resident list page by page use the star key to scroll page up and
number key to scroll page down.
8
LT-979
2.
Key in the dial code associated with the resident you wish to speak to or
press the Telephone Key when the cursor is on the resident’s name. For the
handset version, first pick up the phone and then key in the dial code or
press the Telephone Key.
3.
Once the resident grants entry permission, the door unlocks. For the
handset version, hang up the phone and proceed through the door.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
2
Configuration
This chapter provides detailed information about the TX3 Telephone Access
System configurable functions.
This chapter explains
Version 3.1
LT-979
•
Keypad Navigation
•
Beginning Configuration
•
Accessing the Operation Menu
•
Viewing Configuration Information
•
Viewing the Time and Date
•
Configuration Menu
•
System Option
•
Database Menu
•
Schedule Menu
•
Holidays Menu
•
Set Time & Date
•
Factory Default
•
Input/Output
•
Correlations
•
Changing Passcodes
•
Test LCD
TX3 Telephone Access System Programming Manual
Copyright 2019
9
Configuration
2.1
Keypad Navigation
Figure 1 shows how to use the keypad when in CONFIGURATION MODE.
Note that the keypad buttons can have different functions when creating resident
entries. Refer to 2.8.1 Adding a New Record and Table 1: List of Screens for
more information.
In configuration
mode
Press
to scroll up.
Press
down.
to scroll
In configuration
mode
Press
left.
*
to move
Press
to enter
and confirm selection.
#
Press
to move right for checking
and un-checking the check box.
Figure 1.
2.1.1
Press
to cancel
the selection or exit
mode.
Keypad Navigation
Exiting Configuration Mode
You can exit the configuration mode at any time.
To exit configuration mode
1.
2.2
To exit the configuration mode, press the info key
previous menu.
to return to the
Beginning Configuration
To configure the Telephone Access panel, you must first enter the configuration
mode.
10
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
To enter configuration mode
1.
Press
.
The main menu appears with four choices.
Main Menu
1 Configuration
2 Operation
3 View Cfg Info
4 View time & dat
To access the Operation menu see section 2.3.
To access the View Configuration Information menu see section 2.4.
To view the time and date see section 2.5.
2.
Select Configuration, then press the telephone key.
message appears.
The passcode
Enter the Passcode
[_________]
3.
Enter your passcode, then press the telephone key.
or
If you have not set a personal passcode, press 3 3 3 3, then press the
telephone key. This number is the four-digit factory default. You are now
in configuration mode.
To continue with configuration see section 2.6.
2.3
Accessing the Operation Menu
The Operation Menu lets you view and delete logs.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
11
Configuration
To access the operation menu
1.
Press 9 9 9 9. The configuration information appears.
Main Menu
1 Configuration
2 Operation
3 View Cfg Info
4 View time & dat
2.
Press the
(scroll down) to “Operation”.
3.
Press the telephone key.
4.
Enter your passcode, then press the telephone key.
or
If you have not set a personal passcode, press 3 3 3 3, then press the
telephone key. This number is the four-digit factory default.
5.
The “Operation” menu appears.
Operation Menu
1 View logs
2 Delete logs
To view logs
1.
Press the arrow key to scroll to “View Logs” and press the enter
(telephone) key. The system information appears.
If you have just installed the system, following message appears.
Logging data not
present
12
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.
If recent events have occurred, such as, entering of dial codes and the
opening of the main door, this information appears along with the date and
time as follows.
User log info
Log: 190 of 5000
Event: Call Connect
Acc pt: N/A
Acc Code: D20
Jan 15 2010
12:22 pm
The first four digits represent the index of logged events in sequence
from 1 (0001) up to 5000.
The following letter “D” indicates that the preceding number was a dial
code (D = dial code, K = keyless code).
The term “Acc:” represents the word “access”. The term “Yes” indicates
that access was granted.
3.
Press info key to return to previous menu.
To delete logs
1.
Press the arrow key to scroll to “Delete Logs” and press the telephone key.
The “Delete Logs” selection appears.
Delete Log
User log (s)
System log (s)
All log (s)
2.4
2.
Use the up and down arrow keys to select the log and press the telephone
(enter) key to delete.
3.
Press info key to return to previous menu.
Viewing Configuration Information
Configuration information includes the following:
•
Version 3.1
LT-979
Hardware Version
TX3 Telephone Access System Programming Manual
Copyright 2019
13
Configuration
•
Firmware Version
•
Panel Type (for example, telephone access or card access)
•
Model (for example, 200 names)
•
Last Modified
•
Configuration tool used (for example, Configurator or front panel)
•
Panel ID
•
RS485 Address
•
IP Address
To view configuration information, you must first enter the configuration mode.
To select viewing mode
1.
Press 9 9 9 9. The Main Menu appears. You may need to scroll up or
down to view the entire selection.
Main Menu
1 Configuration
2 Operation
3 View Cfg Info
4 View time & dat
2.5
2.
Press the
(scroll down) to “View Cfg Info”.
3.
Press the telephone key.
4.
The system configuration information appears.
5.
Press the info key
to return to the previous menu.
Viewing the Time and Date
To view time and date
1.
Press 9 9 9 9. The configuration information appears.
Main Menu
1 Configuration
2 Operation
3 View Cfg Info
4 View time & dat
14
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.
Press the
(scroll down) to “View time & date”.
3.
Press the telephone key.
The display shows the time and date.
4.
2.6
Press the info key to return to previous menu.
Configuration Menu
The Configuration Menu consists of the following configurable items.
•
System Option
•
Database Menu
•
Schedule Menu
•
Holidays Menu
•
Set Time & Date
•
Factory Default
•
Input/Output
•
Correlations
•
Changing Passcodes
•
Test LCD
For a description on how to configure these items see paragraphs 2.7 to 2.16.
2.7
System Option
Selecting “System Option” from the Configuration Menu gives you the
following configuration options:
Version 3.1
LT-979
•
Tone/Pulse mode
•
Line Type
•
Main Door DTMF
•
Aux Door DTMF
•
Main door timer
•
Aux door timer
•
Talk timer
•
Language
•
Welcome Message
TX3 Telephone Access System Programming Manual
Copyright 2019
15
Configuration
•
Guard Phone
•
Calling Sch
•
Unlock Schedule
•
Keycode Sch
•
Call Wait Key
•
Keypad Active
•
No of rings
•
Postal usage
•
Scroll speed
•
Day light saving
•
Clock adjustment
•
Elevator Rest Timer
•
Speaker volume
•
MIC volume
•
Select Font (only available on 8-line display)
•
Voice Help Option
•
Auto Unlock Schedule
•
DTMF Sensitivity
•
Handset
For a description on how to configure these items see paragraphs 2.7.1 to 2.7.28
2.7.1
Tone/Pulse mode
Note:
Although this option appears on the front panel, it is not
configurable. The telephone always operates in tone mode. Pulse
dialing is not available.
To access the Tone/Pulse option screen
16
LT-979
1.
Press the arrow key to scroll to “Tone/Pulse mode” and press the
telephone key. The tone/pulse selection appears.
2.
Press the info key to return to the previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.7.2
Line Type
The Line Type function defines each of the 5 telephone lines as ADC, NSL or not
used. By default is line 1 is ADC and lines 2 to 5 as unused.
To define the line type operation
1.
Press the arrow key to scroll to “Line Type” and press the telephone key.
The line selection appears.
Line Type
L-1
L-2
L-3
2.
Using the down arrow key to select L-1, and press the telephone (enter)
key. The line type selection appears.
Select Line Type
[ x ] ADC Type
[ ] NSL Type
[
2.7.3
] Unused
3.
Use the ‘*” and or “#” key to make a selection.
4.
Press the telephone key to enter the selection.
5.
Press the info key to return to the previous menu.
Main Door DTMF
The Main Door DTMF function defines the key the resident presses to open the
main door. The default key is 9.
To define the Main Door DTMF key
1.
Press the arrow key to scroll to “Main Door DTMF” and press the
telephone key. The Main Door DTMF selection appears.
Main Door DTMF
[ x ] ‘9’
[
2.
Version 3.1
LT-979
] ‘0’
Use the up or down key to move to the key number.
TX3 Telephone Access System Programming Manual
Copyright 2019
17
Configuration
3.
Use the * key to select the number and the telephone (enter) key to confirm
the DTMF code. Valid numbers are 1 to 9, * or #.
Note:
Do not select 4 (this is used to refuse entry or disconnect).
Do not use the same number for the main door, auxiliary door, and
call waiting (call waiting works on NSL systems only).
If the Telephone Access System Panel has controller board model
MD-1245, do not select 1, 7, or *.
2.7.4
4.
Press the info key to return to the configuration menu.
5.
Press the info key to return to the previous menu.
Aux Door DTMF
The Aux Door DTMF function defines the key the resident presses to open the
auxiliary door. The default key is 6.
To define the Aux Door DTMF key
1.
Press the arrow key to scroll to “Aux Door DTMF” and press the
telephone key. The Aux Door DTMF selection appears.
Aux Door DTMF
[ ] ‘6’
[ ] ‘7’
[ ] ‘9’
2.
Use the up or down key to move to the key number.
3.
Use the * key to select the number and the telephone (enter) key to confirm
the DTMF code. Valid numbers are 1 to 9, * or #.
Note:
Do not select 4 (this is used to refuse entry or disconnect).
Do not use the same number for the main door, auxiliary door, and
call waiting (call waiting works on NSL systems only).
If the Telephone Access System Panel has controller board model
MD-1245, do not select 1, 7, or *.
4.
18
LT-979
Press the info key to return to the previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.7.5
Main Door Timer
The Main Door Timer function defines the length of time that the main door stays
unlocked after the resident opens the main door using the telephone keypad. The
default is 10 seconds.
To set the Main Door Timer
1.
Press the arrow key to scroll to “Main Door Timer” and press the
telephone key. The Main Door Timer selection entry appears.
Main Door Timer
[ 010 ]
2.7.6
2.
Use the up or down keys to select the number of seconds. Valid
programmable time is 1 to 60 seconds.
3.
Press the info key to return to the previous menu.
Aux Door Timer
The Auxiliary Door Timer function defines the length of time that the auxiliary
door stays unlocked after the resident opens the auxiliary door using the
telephone keypad. The default is 10 seconds.
To set the Auxiliary Door Timer
1.
Press the arrow key to scroll to auxiliary “Door Timer” and press the
telephone key. The Auxiliary Door Timer selection entry appears.
Auxiliary Door Timer
[ 010 ]
2.7.7
2.
Use the up or down keys to select the number of seconds. Valid
programmable time is 1 to 60 seconds.
3.
Press the info key to return to the previous menu.
Talk Timer
The Talk Timer function defines the length of time that a visitor may be on the
telephone with a resident. The default is 60 seconds.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
19
Configuration
To set the Talk Timer
1.
Press the arrow key to scroll to “Talk Timer” and press the telephone key.
The Talk Timer selection entry appears.
Talk Timer
[ 060 ]
2.7.8
2.
Use the up or down keys to select the number of seconds. Valid time is
from 10 to 300 seconds.
3.
Press the info key to return to the previous menu.
Language
The default language is English. Selecting Multi Language makes the opening
screen flip through messages in English, French, and Spanish. Once a key is
pressed, the language that is displayed on the screen at that moment will be used
for the rest of the messages.
To select a language
1.
Press the arrow key to scroll to “Language” and press the telephone (enter)
key. The language selection appears.
Language
[ x ] English
2.
2.7.9
[
] French
[
] Spanish
Press the info key to return to the previous menu.
Welcome Message
The Welcome Message function lets you change the welcome message on the
front of the TX3 Entry Control Panel.
20
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
To change the welcome message
1.
Press the arrow key to scroll to “Welcome Message” and press the
telephone (enter) key. The welcome message appears.
Enter Msg Line - 1
MIRCOM TX3 #1
2.
Press the up arrow key to scroll to the next message line (Line-2) and scroll
up again for next message (Line-3).
3.
Edit each message.
Press the 1 key 9 times to get an asterisk (*).
2.7.10
4.
Press the telephone (enter) key to accept.
5.
Press info key to return to previous menu.
Guard Phone
The Guard phone is an optional auxiliary phone on the lobby control unit that lets
you place calls to residents using their dial code.
To enable the guard phone
1.
Press the arrow key to scroll to “Guard Phone” and press the telephone
(enter) key. The Guard Phone selection appears.
Guard Phone
[
] Guard Phone
[ x ] No Guard Phone
2.7.11
2.
Press the up arrow key to see all 3 lines as shown above.
3.
The default is no guard phone. Use the * key to select the Guard Phone if
required and press the telephone (enter) key to accept.
4.
Press info key to return to previous menu.
Calling Schedule
The Calling Schedule function lets you define when calls to residents are
allowed. For a description on how to define schedules see paragraph 2.9.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
21
Configuration
To set the calling schedule
1.
Press the arrow key to scroll to “Calling Sch” and press the telephone
(enter) key. The Calling Schedule selection appears.
Calling Sch
0 Always
1 Never
2 Weekdays
3 Weekend
4 Evenings
5 Holidays
2.
Press the up and down arrow keys to scroll to one of the schedules shown
above. There are two default schedules to choose; ALWAYS and
NEVER. The other calling schedules are defined by the administrator.
The default is “Always”. See more information about schedules see
paragraph 2.9.
3.
Use the up and down arrow keys to select the schedule and press the
telephone (enter) key to accept.
Note:
4.
2.7.12
The configurator software program defines up to 64 schedules.
Press info key to return to previous menu.
Unlock Schedule
The Unlock Schedule function lets you define when residents can grant access to
a visitor according to the day and/or time.
22
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
To set the Unlock Schedule
1.
Press the arrow key to scroll to “Unlock Sch” and press the telephone
(enter) key. The Unlock Schedule selection appears.
Unlock Sch
0 Always
1 Never
2 Weekdays
3 Weekend
4 Evenings
5 Holidays
2.7.13
2.
Press the up and down arrow keys to scroll through all of the available
schedules as shown above. The default is “Always”.
3.
Use the up and down arrow keys to select the schedule and press the
telephone (enter) key to accept.
4.
Press info key to return to previous menu.
Keycode Schedule
The Keycode Schedule functions lets you define different schedules for keyless
entry.
To set the Keycode Schedule
1.
Press the arrow key to scroll to “Keycode Sch” and press the telephone
(enter) key. The Keycode Schedule selection appears.
Unlock Sch
0 Always
1 Never
2 Weekdays
3 Weekend
4 Evenings
5 Holidays
2.
Version 3.1
LT-979
Press the up and down arrow keys to scroll through the schedules as shown
above. The default is “Always”.
TX3 Telephone Access System Programming Manual
Copyright 2019
23
Configuration
2.7.14
3.
Use the up and down arrow keys to select the schedule and press the
telephone (enter) key to accept.
4.
Press info key to return to previous menu.
Call Wait Key
The Call Wait Key function defines the key the resident presses to place an
outside call on hold. The default key is 2.
Note:
This feature applies to NSL lines only.
To set the Call Wait key
1.
Press the arrow key to select the “Call Wait Key” and press the telephone
(enter) key. The Call Wait Key selection appears.
Call Wait Key
] 1
[
] 2
[
] 3
2.
Press the up and down arrow keys to scroll through the available keys.
Valid keys are 1 to 9, * or #.
3.
The default call wait key is 2 and the available range is 1 to 9. Once
selection is made using the up/down selection keys, press the (enter) key
to accept.
Note:
4.
2.7.15
[
Do not select 4. This is used to refuse entry or disconnect.
Press info key to return to previous menu.
Keypad Active
The Keypad Active function activates the Telephone Access System panel
keypad for the visitor to use during a call. For example, when an answering
machine picks up the call, the visitor is able to use the keypad to leave a message.
24
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
To set the Keypad Active function
1.
Press the arrow key to select “Keypad Active” and press the telephone
(enter) key. The “Keypad Active” selection appears.
Keypad Active
[ x ] Active
[
2.7.16
] Not Active
2.
Press the * key to change the selection and then press the telephone (enter)
key to accept. The default is “Active”.
3.
Press info key to return to the previous menu.
Number of Rings
The number of rings function lets you set the maximum number of rings the
resident receives with a call originates from the entry panel. This feature applies
to NSL lines only.
To set the Number of Rings function
1.
Press the arrow key to select “No of rings” and press the telephone (enter)
key. The “No of rings” entry appears.
No of Rings
[ 007 ]
2.7.17
2.
Use the up and down arrow keys to scroll to the number of rings. The
number of rings ranges from 1 to 15. The default number of rings is 7.
3.
Press the telephone (enter) key to accept.
4.
Press info key to return to the previous menu.
Postal Usage
The “Postal Usage” function lets you define the maximum daily usage for the
postal lock. The range is 1 to 254 and the default is 4. For unlimited usage set the
value to 255.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
25
Configuration
To set the maximum daily postal usage
1.
Press the arrow key to “Postal usage” and press the telephone (enter) key.
The “Postal usage” entry appears.
Postal lock usage
[ 004 ]
2.7.18
2.
Press the up and down arrow keys to select the number. Press the
telephone (enter) key to accept.
3.
Press the info key to return to previous menu.
Scroll Speed
The “Scroll Speed” function lets you set the resident directory scrolling speed for
the Entry Panel display.
To set the Scroll Speed function
1.
Press the arrow to scroll to “Scroll speed” and press the telephone (enter)
key. The “Scroll Speed” entry appears.
Scroll speed
[ 005 ]
2.7.19
2.
Press the up and down arrow keys to scroll through the numbers. The
default is 5, and the range is 1-10.
3.
Press the telephone (enter) key to accept.
4.
Press info key to return to previous menu.
Daylight Saving
The “Daylight Saving” function lets you set the daylight savings time for the
Entry Panel LCU. When active this feature automatically adjusts the time by one
hour in the spring and the fall each year.
26
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
To set the Daylight Saving function
1.
Scroll the arrow to “Daylight Saving” and press the telephone (enter) key.
The “Day light Saving” selection appears.
Daylight saving
< x > Active
<
2.7.20
> Not Active
2.
Press the up and down arrow keys to scroll to the ‘active’ or ‘not active’
selection. The default is ‘active’.
3.
Use the “#” key to make a selection.
4.
Press the telephone (enter) key to accept.
5.
Press info key to return to previous menu.
Clock Adjustment
The “Clock Adjustment” function lets you set the number of seconds to
automatically adjust the clock daily drift. If you find that the clock on your panel
is running slow, use this option to set a daily correction for your panel’s clock.
To set the Clock Adjustment function
1.
Press the arrow to scroll to “Clock Adjustment” and press the telephone
(enter) key. The “Clock Adjustment” entry appears.
Clock adjustment
[ 000 ]
2.7.21
2.
Press the up and down arrow keys to increase the adjustment or the down
arrow key to decrease the adjustment. The range is -15 to 15 seconds and
the default is 0.
3.
Press the telephone (enter) key to accept.
4.
Press info key to return to previous menu.
Elevator Rest Timer
The “Elevator Restriction Timer” function lets you define the elevator access
time.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
27
Configuration
The elevator restriction cabinet houses up to 96 Form C type relay contacts.
These relay contacts are normally connected to the input circuits of the elevator
manufacturer’s button controller. When a resident releases the door, a designated
relay is energized to signal the elevator button controller to enable a particular
floor select button on the elevator and disable all others.
The elevator is restricted to stop only on the selected floor. The time period for
these relays to remain in an energized state depends on the assigned timer period.
Note:
Each elevator restriction cabinet can have only one common timer.
The timer range is 5 to 600 seconds, with 60 seconds as the default.
To set the Elevator Restriction Timer function
1.
Press the arrow key to select the “Elevr Rest Tmr” and press the telephone
(enter) key. The “Elevr Rest Tmr” entry appears.
Elev Rest Timer
[ 060 ]
2.7.22
2.
Press the up and down arrow keys to scroll through the numbers. The
range is 5 to 600 seconds and the default is 60 seconds.
3.
Press the telephone (enter) key to accept the number in view.
4.
Press info key to return to previous menu.
Speaker Volume
The “Speaker Volume” function lets you adjust the Entry Panel speaker volume.
To set the “Speaker Volume” function
1.
Press the arrow key to scroll to “Speaker volume” and press the telephone
(enter) key. The “Speaker volume” entry appears.
Speaker volume
[ 011 ]
2.
28
LT-979
Press the up and down arrow keys to scroll through the numbers. The
range is 1-15 and the default is 11.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.7.23
3.
Press the telephone (enter) key to accept.
4.
Press info key to return to previous menu.
MIC Volume
The “Microphone Volume” function lets you adjust the sensitivity of the Entry
Panel microphone volume.
To set the “Microphone Volume” function
1.
Press the arrow key to scroll to “MIC volume” and press the telephone
(enter) key. The “MIC volume” entry appears.
MIC volume
[ 005 ]
2.7.24
2.
Press the up and down arrow keys to scroll through the numbers. The
range is 1-15 and the default is 5.
3.
Press the telephone (enter) key to accept.
4.
Press info key to return to previous menu.
Select Font Option
The Select Font Option function lets you select the system font and is only
available on the 8-line display.
Note:
Version 3.1
LT-979
The Select Font Option is only available for 8 line display Entry
Panels.
TX3 Telephone Access System Programming Manual
Copyright 2019
29
Configuration
To set the “Select Font Option” function
1.
Press the arrow key to scroll to “Select Font Option” and press the
telephone (enter) key. The “Select Font Option” selection appears.
Select Font
[ x ] Fixed system
2.7.25
[
] Lucida console
[
] Courier bold
[
] Courier reg
[
] Raize
[
] Large Font
2.
Press the up and down arrow keys to scroll to a selection. The default is
‘Fixed system’.
3.
Use the “#” key to make a selection.
4.
Press the telephone (enter) key to accept.
5.
Press info key to return to previous menu.
Voice Help Option
The “Voice Help Option” function lets you turn on or off Voice Help.
To set the “Voice Help Option” function
1.
Press the arrow key to scroll to “Voice Help Option” and press the
telephone (enter) key. The “Voice Help Option” selection appears.
Voice help opt
[ x ] Active
[
30
LT-979
] Not Active
2.
Press the up and down arrow keys to scroll to the ‘Active’ or ‘Not Active’
selection. The default is ‘Active’.
3.
Use the “#” key to make a selection.
4.
Press the telephone (enter) key to accept.
5.
Press info key to return to previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.7.26
Auto Unlock Schedule
The Auto Unlock Schedule function lets you keep the door unlocked for the
duration of the selected schedule. The door locks when the schedule ends.
To set the Auto Unlock Schedule
1.
Press the arrow key to scroll to “Auto Unlock Sch” and press the telephone
(enter) key. The Auto Unlock Schedule selection appears.
Unlock Sch
0 Always
1 Never
2 Weekdays
3 Weekend
4 Evenings
5 Holidays
2.7.27
2.
Press the up and down arrow keys to scroll through all of the available
schedules as shown above. The factory default is “Never”.
3.
Use the up and down arrow keys to select the schedule and press the
telephone (enter) key to accept.
4.
Press info key to return to previous menu.
DTMF Sensitivity
The DTMF sensitivity feature allows the resident to change how sensitive the
TX3 unit is to receiving DTMF signals. DTMF sensitivity can be set from 1 to 8.
A sensitivity of 1 indicates the lowest sensitivity while 8 is the highest
sensitivity. The default sensitivity is 5.
To define the DTMF sensitivity
1.
Press the arrow key to scroll to “DTMF Sensitivity” and press the
telephone key. The DTMF Sensitivity selection appears.
- DTMF Sensitivity [ 005 ]
2.
Version 3.1
LT-979
Use the up or down key to move to select the sensitivity level.
TX3 Telephone Access System Programming Manual
Copyright 2019
31
Configuration
2.7.28
3.
Press the telephone (enter) key to accept.
4.
Press the info key to return to the previous menu.
Handset
The handset option lets you specify if there is a handset connected to your panel.
The default setting is “Hands-free” (that is, no handset).
To set the Handset option
1.
Press the arrow key to scroll to “Handset” and press the telephone key.
The Handset selection appears.
----Handset ---[ x ] Hands-free
[
2.8
] Handset
2.
Use the up or down key to scroll to the “Hands-free” or “Handset”
selection.
3.
Use the “#” key to make a selection.
4.
Press the telephone (enter) key to accept.
5.
Press the info key to return to the previous menu.
Database Menu
The Database Menu consists of the following options.
32
LT-979
•
Add Record
•
Edit Record
•
Delete Record
•
Sort by name
•
Sort by d-code (sort by dial code)
•
Auto Program
•
Delete all Records
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.8.1
Adding a New Record
Table 3 describes the information for adding new resident information. Use the
information in Table 3 to help you add new records.
To enter a resident
1.
From the configuration menu, select the database menu. The database
selection appears.
2.
Press the telephone key to enter the Add Record selection. The Enter Apt#
box appears.
Enter Apt#
[____ ]
3.
Version 3.1
LT-979
To enter an apartment number, use the number keys to select the
appropriate characters. Maximum number of characters is 8. See Figure 2
for information about the characters that correspond to each number.
TX3 Telephone Access System Programming Manual
Copyright 2019
33
Configuration
Press any number key once, twice, three or more times to cycle through the
characters associated with that key. Capital letters appear after you cycle
through all of the lower case letters. When you reach the character you
want, stop pressing the key and the character will remain in the display.
Note that arrow keys are not used.
For Resident Apartment Number Entry Only
1
4
GHI
7
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
press * once = backspace
press # once = space
Figure 2.
Keypad commands for entering an apartment number.
Note:
If you accidentally enter the wrong character while configuring an
apartment number, press * once to backspace.
For example, to enter the apartment number “23B”,
34
LT-979
a.
Press “2” once for the “2”, and then wait for the cursor to advance.
b.
Press “3” once for the “3”, and then wait for the cursor to advance.
c.
Press “2” six times for the letter “B”.
d.
Press the telephone key to save and continue.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
4.
Once you have entered the apartment number and pressed the telephone
key to accept, the Enter Dial Code screen appears. The list of all screens
that you need to configure to add a resident is given in Table 1. Press the
telephone key to save the information for a screen and then advance to the
next screen.
Note:
The keypad functions differently for entering a resident’s name (see
Figure 3) and for entering a resident’s phone number (see
Figure 4). Refer to these figures when entering information for
those screens.
For Resident Name Entry Only
press once = comma
press twice = dash
press 3 times = left bracket
press 4 times = right bracket
press 5 times = /
press 6 times = &
press 9 times = *
press 10 times = 1
press * once = move cursor back
press 0 once to delete a character
press 0 twice = 0
press # once = move cursor forward
Figure 3.
Version 3.1
LT-979
Keypad commands for entering a resident name.
TX3 Telephone Access System Programming Manual
Copyright 2019
35
Configuration
For Resident Telephone Number Entry Only
press to add a comma
(generates a 1 second
delay when dialing)
press to add a semi-colon
(generates a 3 second
delay when dialing)
press to delete
Figure 4.
5.
When all the information for the new resident has been added, the display
shows “New Record Added” and then returns you to the configuration
menu.
Note:
Table 1:
Keypad commands for entering a resident’s telephone
number.
The items marked Edit mode only in Table 1 do not appear when
you add a new record. They appear only when you edit an existing
record. See paragraph 2.8.4 for instructions on editing records.
List of Screens
Database Menu
Enter Apt#
NSL
System
ADC
System
Explanation/Description
YES
YES
Enter the resident’s apartment number (up to 8 digits).
YES
YES
Enter the resident’s dial code (up to 4 digits).
[_ _ _ _]
Enter Dial Code
____
36
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
Table 1:
List of Screens
Database Menu
Main Door sec. code
NSL
System
YES
ADC
System
YES
[_ _ _ _]
Aux Door sec. code
Explanation/Description
Edit mode only
Enter a series of up to 4 digits from 0 to 9 to replace the
main door DTMF key (see section 2.7.3) for the specific
resident. To open the Main Door, the resident enters the
Main Door Security code followed by the # key. DO
NOT select “4”. This is used to refuse entry or
disconnect. Do not use the same number for the main
door, auxiliary door, and call waiting (call waiting
works on NSL systems only).
If the Telephone Access System Panel has controller
board model MD-1245, do not select 1, 7, or *.
YES
YES
[_ _ _ _]
Edit mode only
Enter a series of up to 4 digits from 0 to 9 to replace the
auxiliary door DTMF key (see section 2.7.4) for the
specific resident. To open the Auxiliary Door, the
resident enters the Auxiliary Door Security code
followed by the # key. DO NOT select “4”. This is used
to refuse entry or disconnect. Do not use the same
number for the main door, auxiliary door, and call
waiting (call waiting works on NSL systems only).
If the Telephone Access System Panel has controller
board model MD-1245, do not select 1, 7, or *.
Enter Resident Name
YES
YES
Enter the resident’s name. The name must be unique and
a maximum of 15 characters.
Line In Use
YES
YES
Enter the speech path for resident to communicate to the
ADC line or to a relay control unit. Line 1 is default. Use
arrow keys to scroll and press # or * to make a selection.
N/A
YES
This option is for ADC only. Enter the resident’s
telephone number (up to 18 digits including a comma
that is used as 1 second delay). Use the up arrow key for
a comma (1 second pause) and the down arrow key for a
semi-color (3 second pause). Press Enter (telephone
key) to accept the telephone number.
YES
N/A
Enter the resident’s assigned relay code (NSL only).
[x] Line 1 - 5
Enter Phone number
[____________]
Enter Relay Code
[_ _ _ _]
Enter Keyless Code
Note: Relay codes start at 1 for the first relay, up to 1535.
YES
YES
[_ _ _ _]
Keyless Code Corr
Enter the assigned keyless code, up to 6 digits (if used).
See below for using keyless entry codes.
YES
YES
[x] Main door relay
Use arrow keys to scroll and press # or * to make a
selection.
YES
[_ _]
Version 3.1
LT-979
Edit mode only
Select which door (main, auxiliary or both) can be
opened by the resident using a keyless code.
[ ] Aux door relay
Enter Elev Rest Addr
Edit mode only
YES
Edit mode only
Enter the ID (or address) of the Elevator Restriction
controller for the resident.
TX3 Telephone Access System Programming Manual
Copyright 2019
37
Configuration
Table 1:
List of Screens
NSL
System
Database Menu
Enter Elev Rest Code
YES
ADC
System
YES
Edit mode only
[_ _]
Enter the elevator restriction relay number for the
resident.
Hide Display
YES
YES
Edit mode only
[x] Display
This feature turns the resident information display ON
or OFF. When OFF the resident’s information is only
displayed in configuration mode. Use arrow keys to
scroll and press # or * to make a selection.
Ring Pattern
YES
N/A
Enter the ring pattern for the resident (NSL only). See
Table 2 for available ring patterns. The default is 1. Use
arrow keys to scroll and press # or * to make a selection.
[x] Ring Pattern 1-5
2.8.2
Explanation/Description
Using keyless entry codes
To enter the premises with a keyless entry code, you must first be in normal
mode. While in normal mode, press 0, after which point you are prompted with
“Enter keyless code”. The keyless code is a numeric value from 1 to 999999.
To enter your keyless code
2.8.3
1.
Press 0. The keyless enter code appears.
2.
Enter your keyless code.
Selecting a ring pattern (NSL System only)
The ring pattern selection is part of the Database Menu.
Table 2:
Available Ring Pattern
Ring
Pattern
1
Available Ring Pattern
2s ON
4s OFF
standard
ring A
2
3
38
LT-979
800ms
ON
400ms
OFF
800ms
ON
4s OFF
200ms
ON
400ms
OFF
200ms
ON
400ms
OFF
distinct
ring B
800ms
ON
TX3 Telephone Access System Programming Manual
Copyright 2019
4s OFF
distinct
ring C
Version 3.1
Configuration
Table 2:
4
Available Ring Pattern
200ms
ON
400ms
OFF
800ms
ON
5
2.8.4
400ms
OFF
200ms
ON
4s OFF
distinct
ring D
One single ringing burst
Editing Records
To edit a record
1.
Select “Edit Record” and use the up/down key to scroll through the
residents.
2.
Press the telephone button to select the resident’s name for editing.
1212>Smith
1213 Jones
1214 Hath
1215 Johnson
3.
Use the down arrow key to scroll down the list of fields, such as Apartment
number, Resident name, Dial code Keyless code, relay code, telephone
number, etc. See Table 1 for details.
4.
Once the arrow is pointing to the field that requires a change, press the
telephone key to edit.
5.
Re-enter the correct information.
When you are finished editing the record, the display returns to the record list. At
this point you may edit another record or press information key to return to the
configuration menu.
2.8.5
Deleting Records
Select this feature if you want to delete a resident’s name. This function deletes
one record at a time.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
39
Configuration
To delete a record
1.
Scroll the arrow to “Delete Record” and press the telephone button. The
dial code and resident name appear:
1212>Smith
2.8.6
2.
Scroll the resident names with the up/down arrow keys to the record you
wish to delete.
3.
Press the telephone (enter) key to delete the entire record for the particular
resident. A warning message appears.
4.
When the warning appears “Delete Record? Y. Press the telephone key to
accept or the info key to cancel.
5.
Once the record has been deleted, the screen will return to the Delete
Record function. At this point you may delete other records or press the
info key to return to the configuration menu.
Sorting by Name
Select this feature if you want the list of residents to be sorted alphabetically by
name.
To sort by name
1.
Scroll the arrow to “Sort by Name” and press the enter (telephone) key.
Selecting this feature during database downloaded displays the following
message:
Sorting please wait
The display now returns to the configuration menu.
40
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.8.7
Sorting by dial code
To sort by d-code
Select this feature if you want the list of residents to be sorted numerically by dial
code. Scroll the arrow to “Sort by d-code” and press enter (telephone) key. If you
have just downloaded the database, the following message appears:
Sorting please wait
The display now returns to the configuration menu.
2.8.8
Auto Programming
Auto programming allows you to add a group of residents from a minimum of 10
to a maximum of 200 names. This function allows you to auto program the
number of residents, resident name, start dial code, start keyless code and line
number to use.
This feature is particularly useful when adding a large number of residents into
the system.
Table 3 describes the information you will need to auto program the panel.
Table 3:
Auto Programming Information
Programming Menu
Number of Records
NSL
System
ADC
System
YES
YES
Enter the total number of residents to auto program (4
digits). Scroll up or down to the desired number, then
press enter (telephone key). Must be 10 or more.
YES
YES
Enter the resident’s name (maximum 10 characters).
[____]
Enter Resident Name
Explanation/Description
[____________]
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
41
Configuration
Table 3:
Auto Programming Information
Start Dialcode
YES
YES
Enter the start number of Dial Codes to auto program.
The starting code will be entered in increments of 1, up
to the number of residents entered.
YES
YES
Enter the start number of the keyless codes, if used.
The starting code will be entered in increments of 1, up
to the number of residents entered. These codes are
used by the visitors to enter without calling the
resident.
Line Number to use [__]
YES
YES
Enter the Line number you wish for this lobby unit to
connect to. This Line numbers will be used by the
number of residents entered. Lines 1 to 5 are available.
Start Relay Number
YES
N/A
Enter the start relay number to auto program. The
starting relay number will be entered in increments of
1, up to the number of residents entered. Please note
that the relay number starts at 1 for the first relay.
[____]
Start Keyless Code
[____]
[____]
To use the auto program
1.
Scroll the arrow to “Auto Program” database menu and press the enter
(telephone) key. The display will now show the following message:
Number of Records
< 010>
2.
Use the up arrow to move from number of residents in increments of 5 to
the desired number. The maximum depends on the TX3 Model (it can be
200, 1000 or 2000).
Note:
3.
Only 200 names can be added at a time.
Press the telephone (enter) key to accept. The next screen will ask for
resident name. Enter one of the resident names using the alphanumeric
keypad.
Enter Resident
Name
4.
Press the telephone (enter) key to accept. The next screen will ask for the
resident’s dial code. All the rest of the dial codes increase by one.
Start Dial Code
42
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
5.
Use the number keypad to enter the start dial code. The next screen asks
for the resident’s keyless code. All the rest of the keyless code increase by
one.
Start Keyless Code
6.
Use the number keypad to enter the start keyless code. The next screen
asks which audio line to use.
Line Number to use
2.8.9
7.
Use the up arrow to enter the line number. Press the enter (telephone) key
to accept.
8.
Press info key to return to previous menu. View the residents entered by
scrolling page up and down using the * and # keys. To enter the proper
resident names, use the edit feature.
Deleting All Records
Select this feature if you want to delete all the resident data (all names, dial codes,
everything).
To delete all the resident data
1.
Scroll the arrow to “Delete all Records” and press the enter (telephone)
key. The following message appears:
Delete all records?
2.
2.9
Press the enter (telephone) key to accept or the info key to cancel. The
display now returns to the configuration menu.
Schedule Menu
The schedule menu lets you set up a timetable to establish when certain panel
functions are permitted to occur, such as when calls to residents are allowed,
when residents can grant access to a visitor or when the postal lock can be used.
These schedules are designated and listed by name, and are available for
selection wherever it is necessary to invoke access permission.
Each schedule consists of eight periods.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
43
Configuration
To configure a schedule
1.
Press the arrow to scroll to “Schedules” in the main configuration menu
and press the enter (telephone) key. The “Schedules” selection appears.
Schedule Options
1 Add
2 Edit
3 Delete
2.
You are able to add, edit or delete any schedule except “Always” and
“Never”.
To add a schedule
1.
Select Add. The “Enter Label” selection appears.
Enter Label
2.
Create a label, then add a start, end time and the days of the week the
schedule will be active.
3.
Define each of the eight periods for the schedule. At the end of the
schedule configuration the “Schedule Added” message appears.
Schedule Added
4.
Press the telephone (enter) key to accept.
5.
Press info key to return to previous menu.
To edit or delete a schedule
44
LT-979
1.
Select Edit or Delete. A list of all the schedules appears.
2.
Press the arrow keys to scroll to the schedule you would like to edit or
delete.
3.
Press the telephone (enter) key to accept.
4.
Press info key to return to previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.10
Holidays Menu
The Holidays menu lets you define the holidays for your schedules. When you
select Holiday for any of the periods in a schedules, all of the holidays defined in
this menu are added to the period for that schedule. By default, the TX3 system
comes with “New Year” already defined as a holiday.
To configure a holiday
1.
Scroll the arrow to “Holidays” in the main configuration menu and press
the enter (telephone) key. The “Holiday Options” selection appears.
Holiday Options
1 Add
2 Edit
3 Delete
To add a holiday
1.
Select Add. The “Enter Label” menu appears. You can add, edit or delete
any holiday. By default, “New Year” is already programmed into the
system.
2.
Create a label, then a start and end time. Then select if this is holiday is an
annual occurrence.
3.
Press the telephone (enter) key to accept. The message “Holiday Added”
is displayed on the screen and you are then returned to the “Holiday
Options” screen.
To edit a holiday
Version 3.1
LT-979
1.
Select “Edit”. A list of all the holidays appears.
2.
Press the arrow keys to scroll to the holiday you would like to edit.
3.
Press the telephone (enter) key to accept.
TX3 Telephone Access System Programming Manual
Copyright 2019
45
Configuration
4.
Press the arrow keys to scroll to the item you want to edit for the holiday
(that is, “Label”, “Start Time/Date”, “End Time/Date”, or “Repeat
Annually“), and then press the telephone (enter) key.
---New Year
1 Label
--
2 Start Time/Date
3 End Time/Date
4 Repeat Annually
5.
Make your edits to the item, and then press the telephone (enter) key to
accept it. You are returned to the Holiday edit screen.
6.
If you want to edit more items for the holiday, repeat steps 4 and 5 above.
7.
Press info key to save your edits.
8.
Press the info key to return to the “Holiday Options” menu.
To delete a holiday
2.11
1.
Select Delete. A list of all the holidays appears.
2.
Press the arrow keys to scroll to the holiday you would like to delete, and
then press the telephone (enter) key to select the holiday for deletion.
3.
Press the telephone (enter) key to accept the deletion.
4.
Press the info key to return to the “Holiday Options” menu.
Set Time & Date
To set time & date
1.
Scroll the arrow to “Set time & date” in the main configuration menu and
press the enter (telephone) key.
The time and day information appears.
Set Time/Date
Apr 17, 2018 03:23 PM
2.
46
LT-979
Use the * and # keys to select the month, day, year, hour, minute, and AM
or PM. Use the * key to move left and the # key to move right.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
2.12
3.
Use the up and down arrow keys to change the time and date.
4.
Press the enter (telephone) key to save the changes.
Factory Default
The “Factory Default” selection lets you apply the factory default settings for the
telephone access system.
Note:
Selecting the Factory Default does not delete any resident
information.
To set the Factory Default
1.
Scroll the arrow to “Factory Dflt” in the main configuration menu and
press the enter (telephone) key. The Factory Default confirmation
selection appears.
Reset to default? <Y>
2.
2.13
Press the telephone (enter) key to accept or i to cancel.
Input/Output
The Inputs and Outputs selection lets you define specific devices connected to
each input and output.
To access Inputs and Outputs
1.
Press the arrow key to scroll to “Input/Output” in the main configuration
menu. The “Input/Output” selection appears.
Ipt/Opt Options
1 Inputs
2 Outputs
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
47
Configuration
To define inputs
1.
Press the arrow key to scroll to Inputs, and press the enter (telephone) key.
The “Input Types” selection appears.
Input Types
1 Postal lock
2 Fire P Override
3 Door Sense
4 GP Input 3
5 GP Input 4
2.
Press the arrow key to scroll to the input you wish to configure and press
the telephone (enter) key. The Input Active State selection appears.
Ipt Active State
[
] Close
3.
Use the “#” key to define the input state as open or closed.
4.
Press the telephone (enter) key to accept. The circuit supervision selection
appears.
Supervised for[ x ] No supervision
48
LT-979
[
] Open
[
] Short
[
] Open & Short
5.
Press the arrow key to scroll to the input you wish to configure and use the
“#” key to define the input state as No supervision, Open, Short or Open &
Short
6.
Press the telephone (enter) key. The “Input Types” selection appears.
7.
Proceed with the rest of the input configuration or
8.
Press info key to return to previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
To define outputs
1.
Press the arrow key to scroll to Outputs, and press the enter (telephone)
key. The Output selection appears.
Output Types
1 Main Door lock
2 Aux Door lock
3 GP Output 3
4 GP Output 4
2.
Press the arrow key to scroll to the output you wish to configure and press
the telephone (enter) key. The Output Active State selection appears.
Opt Active State
< > De-energized
< x > Energized
2.14
3.
Press the arrow key to scroll to the input you wish to configure and use the
“#” key to define the output state as energized or de-energized.
4.
Press the telephone (enter) key. The Output selection appears.
5.
Proceed with the rest of the input configuration or
6.
Press info key to return to previous menu.
Correlations
The Correlation selection lets you associate specific input events with specific
output actions.
To configure a correlation
1.
Press the arrow to scroll to “Correlations” in the main configuration menu
and press the enter (telephone) key. The “Correlation” selection appears.
Correlation
1 Add
2 Edit
3 Delete
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
49
Configuration
To make a correlation
1.
Select Add. The “Event” selection appears
Event Type
[ X ] Input Activate
2.
[
] Input Normal
[
] Call Started
[
] Call Ended
[
] Call Connected
[
] Access granted
[
] Access denied
Press the arrow key to scroll to a specific type of input and press the
telephone (enter) key. The Event Data selection appears.
Event Data
[ X ] Postal Lock
3.
[
] Fire P Overrid
[
] Door Sense
[
] GP Input1
[
] GP Input2
Press the arrow key to scroll to a specific type of input event and press the
telephone (enter) key. The “Response Type” selection appears.
Response Time
[ X ] Turn Output ON
[
50
LT-979
] Turn Output OFF
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
4.
Press the arrow key to scroll to a specific type of output action (response)
and press the telephone (enter) key. The “Response Data” selection
appears.
Response Data
[
] Main door lock
[
] Aux door lock
[ X ] GP output 1
[
5.
] GP output 2
Press the arrow key to scroll to a specific output and press the telephone
(enter) key. The “Schedule” selection appears
Select Sch
0 Always
6.
Press the arrow key to select a specific schedule and press the telephone
(enter) key. The “Correlation Timer” entry appears.
Corr Timer
[-001]
7.
Press the arrow key to specify the duration for the correlation in seconds.
-001 means that there is no timer; in other words the correlation is always
active.
8.
After you have selected the duration for the correlation, press the
telephone (enter) key.
The “Node Address” entry appears.
An output action occurs on the panel designated by its node address,
including the originating the panel. Setting an address of 000 sets the
output action for all panels.
Node Address
[001]
Version 3.1
LT-979
9.
Press the arrow key to scroll to select a node address and press the
telephone (enter) key. The message Correlation Updated appears.
10.
Press the info key to return to previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
51
Configuration
To edit or delete a correlation
2.15
1.
Press the arrow to scroll to “Correlations” in the main configuration menu
and press the enter (telephone) key. The “Correlation” menu appears.
2.
Select Edit or Delete. A list of all the correlations appears.
3.
Press the arrow keys to scroll to the correlation you would like to edit or
delete.
4.
Press the telephone (enter) key to accept.
5.
Press info key to return to previous menu.
Changing Passcodes
The Changing Passcodes selection lets you change your passcode for your access
level. There are three access levels.
Level 1. Not used.
Level 2. Level 2 passcode allows access to the operation menu.
Level 3. Level 3 passcode allows access to both operation and configuration
menu. The level 3 passcode is also a network passcode used by the configurator
software. If the level 3 passcode changes, the configurator will not be able to
connect to the panel unless the network password is set to the level 3 passcode.
To change a passcode
1.
Press the arrow to scroll to “Change Passcode” in the main configuration
menu and press the enter (telephone) key. The “Enter Access Level” entry
appears.
Enter Access Level
< 001>
2.
52
LT-979
Press the arrow keys to scroll to your access level and press the telephone
(enter) key to accept.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Configuration
3.
Enter the new passcode. It can be up to 10 digits long.
Note:
4.
If you forgot the new passcode, call Mircom’s Technical Support
Department. See Technical Support contact information in
Section 1.5).
Press the telephone (enter) key to accept. The “Enter New Passcode” entry
appears.
Enter new Passcode
----------
5.
Press the enter (telephone) key to enter the new passcode. The “Re-enter
New Passcode” entry appears.
Re-enter new Passcode
----------
2.16
6.
Re-enter the new passcode.
7.
Press the enter (telephone) key to finalize entry of the new passcode.
8.
Press info key to return to previous menu.
Test LCD
The Test LCD selection lets you view all 255 character lines.
To test the LCD
Version 3.1
LT-979
1.
Press the arrow to scroll to “Test LCD” in the main configuration menu
and press the enter (telephone) key. The “Test LCD” menu appears.
2.
Press the arrow keys to scroll through the character lines.
3.
Press info key to return to previous menu.
TX3 Telephone Access System Programming Manual
Copyright 2019
53
Warranty and Warning Information
WARNING!
Please read this document CAREFULLY, as it contains important warnings,
life-safety, and practical information about all products manufactured by the
Mircom Group of Companies, including Mircom and Secutron branded
products, which shall include without limitation all fire alarm, nurse call,
building automation and access control and card access products (hereinafter
individually or collectively, as applicable, referred to as “Mircom System”).
NOTE TO ALL READERS:
1.
Nature of Warnings. The within warnings are communicated to the
reader out of an abundance of caution and create no legal obligation for
Mircom Group of Companies, whatsoever. Without limiting the
generality of the foregoing, this document shall NOT be construed as in
any way altering the rights and obligations of the parties, governed by the
legal documents that apply in any given circumstance.
2.
Application. The warnings contained in this document apply to all
Mircom System and shall be read in conjunction with:
4.
a.
the product manual for the specific Mircom System that applies
in given circumstances;
b.
legal documents that apply to the purchase and sale of a Mircom
System, which may include the company’s standard terms and
conditions and warranty statements;
c.
other information about the Mircom System or the parties’ rights
and obligations as may be application to a given circumstance.
Security and Insurance. Regardless of its capabilities, no Mircom
System is a substitute for property or life insurance. Nor is the system a
substitute for property owners, renters, or other occupants to act prudently
to prevent or minimize the harmful effects of an emergency situation.
Building automation systems produced by the Mircom Group of
Companies are not to be used as a fire, alarm, or life-safety system.
NOTE TO INSTALLERS:
All Mircom Systems have been carefully designed to be as effective as possible.
However, there are circumstances where they may not provide protection. Some
reasons for system failure include the following. As the only individual in
54
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
contact with system users, please bring each item in this warning to the attention
of the users of this Mircom System. Failure to properly inform system end-users
of the circumstances in which the system might fail may result in over-reliance
upon the system. As a result, it is imperative that you properly inform each
customer for whom you install the system of the possible forms of failure:
5.
Inadequate Installation. All Mircom Systems must be installed in
accordance with all the applicable codes and standards in order to provide
adequate protection. National standards require an inspection and
approval to be conducted by the local authority having jurisdiction
following the initial installation of the system and following any changes
to the system. Such inspections ensure installation has been carried out
properly.
6.
Inadequate Testing. Most problems that would prevent an alarm a
Mircom System from operating as intended can be discovered by regular
testing and maintenance. The complete system should be tested by the
local authority having jurisdiction immediately after a fire, storm,
earthquake, accident, or any kind of construction activity inside or outside
the premises. The testing should include all sensing devices, keypads,
consoles, alarm indicating devices and any other operational devices that
are part of the system.
NOTE TO USERS:
All Mircom Systems have been carefully designed to be as effective as possible.
However, there are circumstances where they may not provide protection. Some
reasons for system failure include the following. The end user can minimize the
occurrence of any of the following by proper training, testing and maintenance of
the Mircom Systems:
Version 3.1
LT-979
7.
Inadequate Testing and Maintenance. It is imperative that the systems
be periodically tested and subjected to preventative maintenance. Best
practices and local authority having jurisdiction determine the frequency
and type of testing that is required at a minimum. Mircom System may not
function properly, and the occurrence of other system failures identified
below may not be minimized, if the periodic testing and maintenance of
Mircom Systems is not completed with diligence and as required.
8.
Improper Operation. It is important that all system users be trained in
the correct operation of the alarm system and that they know how to
respond when the system indicates an alarm. A Mircom System may not
function as intended during an emergency situation where the user is
unable to operate a panic or emergency switch by reason of permanent or
temporary physical disability, inability to reach the device in time,
unfamiliarity with the correct operation, or related circumstances.
TX3 Telephone Access System Programming Manual
Copyright 2019
55
56
LT-979
9.
Insufficient Time. There may be circumstances when a Mircom System
will operate as intended, yet the occupants will not be protected from the
emergency due to their inability to respond to the warnings in a timely
manner. If the system is monitored, the response may not occur in time
enough to protect the occupants or their belongings.
10.
Carelessness or Safety Hazards. Moreover, smoke detectors may not
provide timely warning of fires caused by carelessness or safety hazards
such as smoking in bed, violent explosions, escaping gas, improper
storage of flammable materials, overloaded electrical circuits or children
playing with matches or arson.
11.
Power Failure. Some Mircom System components require adequate
electrical power supply to operate. Examples include: smoke detectors,
beacons, HVAC, and lighting controllers. If a device operates only by AC
power, any interruption, however brief, will render that device inoperative
while it does not have power. Power interruptions of any length are often
accompanied by voltage fluctuations which may damage Mircom
Systems or other electronic equipment. After a power interruption has
occurred, immediately conduct a complete system test to ensure that the
system operates as intended.
12.
Battery Failure. If the Mircom System or any device connected to the
system operates from batteries it is possible for the batteries to fail. Even
if the batteries have not failed, they must be fully charged, in good
condition, and installed correctly. Some Mircom Systems use replaceable
batteries, which have a limited life-span. The expected battery life is
variable and in part dependent on the device environment, usage and type.
Ambient conditions such as high humidity, high or low temperatures, or
large temperature fluctuations may reduce the expected battery life.
Moreover, some Mircom Systems do not have a battery monitor that
would alert the user in the event that the battery is nearing its end of life.
Regular testing and replacements are vital for ensuring that the batteries
function as expected, whether or not a device has a low-battery monitor.
13.
Physical Obstructions. Motion sensors that are part of a Mircom System
must be kept clear of any obstacles which impede the sensors’ ability to
detect movement. Signals being communicated by a Mircom System may
not reach the receiver if an item (such as metal, water, or concrete) is
placed on or near the radio path. Deliberate jamming or other inadvertent
radio signal interference can also negatively affect system operation.
14.
Wireless Devices Placement Proximity. Moreover all wireless devices
must be a minimum and maximum distance away from large metal
objects, such as refrigerators. You are required to consult the specific
Mircom System manual and application guide for any maximum
distances required between devices and suggested placement of wireless
devices for optimal functioning.
15.
Failure to Trigger Sensors. Moreover, Mircom Systems may fail to
operate as intended if motion, heat, or smoke sensors are not triggered.
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Version 3.1
LT-979
a.
Sensors in a fire system may fail to be triggered when the fire is
in a chimney, walls, roof, or on the other side of closed doors.
Smoke and heat detectors may not detect smoke or heat from fires
on another level of the residence or building. In this situation the
control panel may not alert occupants of a fire.
b.
Sensors in a nurse call system may fail to be triggered when
movement is occurring outside of the motion sensors’ range. For
example, if movement is occurring on the other side of closed
doors or on another level of the residence or building the motion
detector may not be triggered. In this situation the central
controller may not register an alarm signal.
3.
Interference with Audible Notification Appliances. Audible
notification appliances may be interfered with by other noise sources such
as stereos, radios, televisions, air conditioners, appliances, or passing
traffic. Audible notification appliances, however loud, may not be heard
by a hearing-impaired person.
4.
Other Impairments. Alarm notification appliances such as sirens, bells,
horns, or strobes may not warn or waken a sleeping occupant if there is an
intervening wall or door. It is less likely that the occupants will be alerted
or awakened when notification appliances are located on a different level
of the residence or premise.
5.
Software Malfunction. Most Mircom Systems contain software. No
warranties are provided as to the software components of any products or
stand-alone software products within a Mircom System. For a full
statement of the warranties and exclusions and limitations of liability
please refer to the company’s standard Terms and Conditions and
Warranties.
6.
Telephone Lines Malfunction. Telephone service can cause system
failure where telephone lines are relied upon by a Mircom System. Alarms
and information coming from a Mircom System may not be transmitted if
a phone line is out of service or busy for a certain period of time. Alarms
and information may not be transmitted where telephone lines have been
compromised by criminal tampering, local construction, storms or
earthquakes.
7.
Component Failure. Although every effort has been made to make this
Mircom System as reliable as possible, the system may fail to function as
intended due to the failure of a component.
8.
Integrated Products. Mircom System might not function as intended if
it is connected to a non-Mircom product or to a Mircom product that is
deemed non-compatible with a particular Mircom System. A list of
compatible products can be requested and obtained.
TX3 Telephone Access System Programming Manual
Copyright 2019
57
Warranty
Purchase of all Mircom products is governed by:
https://www.mircom.com/product-warranty
https://www.mircom.com/purchase-terms-and-conditions
https://www.mircom.com/software-license-terms-and-conditions
58
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
Special Notices
Product Model Number: TX3
AC REN (U.S.): 0.0B
AC REN (CANADA): 0.0
Complies With
Federal Communications Commission (FCC):
•
TIA-968-A Technical requirement for connection of equipment tot he
telephone network.
•
CFR 47, Part 15, Subpart B, Class B
•
Unintentional Radiators
Industry Canada (IC):
•
Terminal attachment programme
•
CS-03, Issue 8 - Certification Specifications
•
ICES-003, ISSUE 4, CLASS B
•
Verification Authorization - Digital Apparatus
Registration Numbers
FCC (U.S.): 1M8TE00BTX3
IC (Canada): 1156A-TX3
Industry Canada Notice for all TX3 Products Sold in Canada
The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational, and safety requirements. Industry Canada does not guarantee the
equipment will operate to the user's satisfaction. Before installing this
equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunication company. The equipment must also be
installed using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent degradations
of service in some situations.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
59
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alteration made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment. Users should ensure for their own protection that the earth ground
connections of the power utility, telephone lines and internal metallic water pipe
system, if present, are connected together. This is necessary both for proper
operation and for protection.
Caution:
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate.
Note:
The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject
only to the requirement that the sum of the RENs of all the devices
does not exceed five.
FCC Notice for all TX3 Products Sold in the U.S.A.
Type of Service
The TX3 is designed to be used on standard device telephone lines. It connects to
the telephone line by means of a standard jack called the USOC RJ-11C (or
USOC FJ45S). Connection to telephone company-provided coin service
(central office implemented systems) is prohibited. Connection to party lines
service is subject to state tariffs.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can.
In order to do this, it may occasionally be necessary for them to make changes in
their equipment, operations or procedures. If these changes might affect your
service or the operation of your equipment, the telephone company will give you
notice, in writing, to allow you to make any changes necessary to maintain
uninterrupted service.
In certain circumstances, it may be necessary for the telephone company to
request information from you concerning the equipment which you have
connected to your telephone line. Upon request of the telephone company,
provide the FCC registration number and the ringer equivalence number (REN);
both of these items are listed on the equipment label. The sum of all of the RENs
60
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1
on your telephone lines should be less than five in order to assure proper service
from the telephone company. In some cases, a sum of five may not be useable on
a given line.
Changes to Telephone Service
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the telephone company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service.
Ringer Equivalence Number
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
telephone company. For products approved after July 23, 2001, the REN for this
product is Customer Information 3 July 2003 part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the
REN is separately shown on the label.
If Problems Arise
If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to the
telephone network. If the telephone company notes a problem, they may
temporarily discontinue service. When practical, they will notify you in advance
of this disconnection. If advance notice is not feasible, you will be notified as
soon as possible. When you are notified, you will be given the opportunity to
correct the problem and informed of your right to file a complaint with the FCC.
Contact your telephone company if you have any questions about your telephone
line. In the event repairs are ever needed on the Communicator, they should be
performed by Mircom or an authorized representative of Mircom. For
information contact Mircom at the address and telephone numbers in
paragraph 1.5.
If this equipment, TX3 Telephone System, causes harm to the telephone
network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn't practical,
the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
Version 3.1
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
61
Product Identifier
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the back of the front panel cover of this equipment is
a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the
telephone company.
Telephone Connection
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. You are responsible for installing a
compliant telephone cord and modular plug into this product as described in this
manual. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
Equipment Failure
If trouble is experienced with the TX3 Telephone/Card Access System, for
repair or warranty information, please contact Mircom using the numbers in
paragraph 1.5. If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment until the
problem is resolved.
Use With Alarm Auto Dialers
If your institution has specially wired alarm equipment connected to the
telephone line, ensure the installation of the TX3 Telephone/Card Access
System does not disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone company or a qualified
installer.
62
LT-979
TX3 Telephone Access System Programming Manual
Copyright 2019
Version 3.1

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement