STAIN TECHNICAL DATA CST-02 CONCRETE STAIN SPRAYS DESCRIPTION AND USES ..PRODUCT APPLICATION (cont.) . ® APPLICATION Rust-Oleum Concrete Stain is a penetrating water-based stain designed for use on bare interior and exterior concrete and masonry surfaces. This convenient spray is ideal for use on small statuary, for adding accent colors to larger projects or for touch up of previously stained projects. Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 10-12” from surface and spray in a circular or figure eight pattern. Apply the basecoat evenly (100% coverage) and allow to dry approximately 1 hour before applying accent color(s). Keep the can the same distance from the surface. Keep the can in motion while spraying. If desired, apply accent color(s) over the basecoat to provide the desired level of contrast. Allow to air dry a minimum of 1 hour before sealing. Note: Final results may vary do to the natural variance that exists in concrete. Do not use near open flame. Application works best on bare interior and exterior concrete and masonry surfaces. Existing coatings or sealers must be removed prior to applying Concrete Stain Sprays. Test for a sealer by lightly sprinkling water onto the concrete. If water droplets bead up, rather than soak into the concrete, then a sealer is present and it must be removed prior to staining. Concrete Stain Sprays features a comfort tip with a wider finger pad to reduce fatigue caused by continuous spraying and an any-angle tip which allows you to spray at any angle. .PRODUCTS SKU 247129 247161 247162 247163 247166 247167 DRY & RECOAT . Dry and recoat times are based on 70°F (21°C) and 50% relative humidity. Allow more time at cooler temperatures. Dries to touch in 1 hour and can be recoated in 1 hour. Description Burnt Brick Sienna Earth Brown Limestone Gloss Clear Matte Clear . SPRAYING CONDITIONS CLEAN UP Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in home trash compactor. . CLOGGING Apply when ambient air temperature is 50-90°F (10-32°C) and the relative humidity is below 85%. Do not stain outdoors if rain is expected within 48 hours. To minimize overspray, properly mask adjoining areas and avoid staining in windy conditions. ..PRODUCT APPLICATION If the valve clogs, twist and pull off spray tip and rinse in a solvent such as mineral spirits. Do not insert any object into can valve opening. . SURFACE PREPARATION Proper surface preparation is critical to performance. Allow new concrete to cure for a minimum of 28 days prior to coating. Before staining bare concrete surfaces, remove any oil or grease spots with a heavy duty degreaser, sold separately. Follow manufacturer’s directions for use. When staining small statuary or when using to add and accent color over a previously stained surface, etching is not necessary. Make sure the surface is clean and free of dirt. 1 Form: GDH-1001 Rev.: 053017 TECHNICAL DATA CONCRETE STAIN SPRAYS PHYSICAL PROPERTIES . Physical Properties CONCRETE STAIN SPRAYS Resin Type Water-based Acrylic Pigment Type Varies with color Solvents Water, Dimethyl Ether, Isopropyl Alcohol MIR 0.95 Max Fill Weight 15 ounces Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70-80ºF (2127ºC) and 50% Relative Humidity Approximately 12-16 sq.ft./can 2 (1.1-1.5 m /can Touch 1 hours Recoat 1 hour Shelf Life 5 years Flash Point -156°F (-104°C) Safety Information For additional information, see SDS The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice. Rust-Oleum Corporation 11 Hawthorn Parkway Vernon Hills, Illinois 60061 An RPM Company Phone: 877•385•8155 www.rustoleum.com Form: GDH-1001 Rev.: 053017
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021