INSTRUCTION MANUAL A A A A
DANGER FIRE EXPLOSION FUMES
BERNZÜMATIC
Model: BZ8250HT
A DANGER
This torch is used with a flammable product. Failure to comply with these Warnings and Instructions may result
in an explosion or fire that may cause property damage, serious personal injury or death.
Read and comply with the instructions and warnings in this manual and familiarize yourself with the torch before lighting
and using. Review instructions and warnings periodically to maintain awareness. Do not try to operate before reading
Instructions.
Torches are to be used with propane only. Use only with Hand Held Propane Cylinders specifically designed for use with
torches. (DOT-39 or TC-39M cylinders)
A WARNING
e Materials used in the construction of this device may contain brass (which may contain lead), a chemical known
to the State of California to cause birth defects or other reproductive harm.
e Combustion by-products produced when using this device contain chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.
e Keep torch out of reach of children and anyone who has not read instructions. Do not point torch towards face, other
persons or flammable objects. Never attempt to use torch as a cigarette lighter.
e Disconnect cylinder when not in use.
e Never attempt to modify the torch construction and Never use unapproved accessories or fuels.
e Be extra careful when using the torch outdoors on sunny or windy days. Bright sun makes it impossible to see the torch's
flame. Wind may carry the torch’s heat back towards you or other areas not intended to be heated. Windy conditions may
also cause sparks to be blown into other areas with combustible materials.
e Treat the torch as you would any fine tool or instrument. Do not drop, throw, or otherwise abuse.
e Do not use a leaking, damaged or malfunctioning torch.
e Radiant energy can harm your eyes. Wear goggles having ANSI 287.12979 shade lens number appropriate to the torch
operation as indicated; brazing and light cutting (3 or 4), medium cutting and light welding (4 or 5), heavy cutting and
medium/heavy welding (5-8).
e Never use torch to strip paint.
e Heating a surface may cause heat to be conducted to adjoining surfaces that may be combustible or become
pressurized when heated. Always check to make sure no unintended parts or materials are being heated.
e Work only in well-ventilated areas. Avoid the fumes from fluxes, lead-based paint, and all metal heating operations. Be
especially careful to avoid fumes from cadmium plating and galvanized metal- remove these coatings in the area to be
heated by filing or sanding prior to heating.
e Avoid contact of flux with skin or eyes.
e Always wear safety glasses, protective gloves and use proper tools to handle hot work.
e Be aware that the tip of the torch can get extremely hot during use. Take precautions to protect yourself and others from
accidental burns.
e Never use the torch on or near combustibles. Be especially careful around motor vehicles or any gasoline-fired products
and beware of hidden fuel lines and tanks.
e Always make certain the torch is placed on a level surface when connected to the fuel cylinder to reduce the risk of
accidental tip over. Be sure the torch is not pointed in a direction which could cause nearby objects to ignite when the
torch is set down.
e Never leave the torch unattended when lit.
e Never attempt to repair or heat a gasoline tank, a chemical drum an aerosol can, a compressed gas container that held
flammable liquid or gas or any other chemical. Heating these is extremely dangerous, especially after they have been
“emptied”.
DO NOT DISCARD THESE WARNINGS AND INSTRUCTIONS
200 Old Wilson Bridge Road
Columbus, OH USA 43085 06/24/15
(866) 928-2657
worthingtoncylinders.com | bernzomatic.com
When thawing pipes, be very careful not to overheat surrounding materials. Use heat shield.
Always have a fire extinguisher and a bucket of water near the torch and work area.
This torch consumes oxygen and must only be used in well ventilated areas. Do not use in a confined space.
Never attempt to light the torch with a setting that would result in a main flame less than one quarter inch (1/4”) long.
An excessively short flame will cause lighting difficulties, will result in inefficient heating and may damage the ignition
mechanism.
A DANGER
EXTREMELY FLAMMABLE. CONTENTS UNDER PRESSURE.
Keep fuel cylinders away from heat or flame.
It is illegal and dangerous to refill the cylinder. When empty, obtain a new cylinder from your dealer.
Federal law prohibits transportation if refilled. Penalty up to $500,000 fine and five years imprisonment (49 U.S.C. 5124)
Keep cylinders out of reach of children
Avoid prolonged exposure to sunlight.
Do not store near source of heat or in a room used for habitation.
Always detach torch from cylinder when not in use.
Do not breathe gas, fumes, vapor or spray. If inhaled, remove affected person to fresh air.
Avoid contact with eyes or skin. In case of contact with eyes, rinse immediately with plenty of water and seek medical
advice. For skin contact, flush with large amounts of water.
When cylinder is empty, discard in a safe place. Do not throw cylinder in fire. Do not puncture or incinerate cylinder.
ASSEMBLY
1.
w N
Make sure regulator valve is off by turning adjustment knob clockwise until it stops. A light stop is sufficient.
Do not force.
Hold regulator valve and thread fuel gas cylinder into regulator by turning the fuel gas cylinder clockwise,
hand tighten only. Do not force.
Check all joints and couplings periodically to insure against loose connections. With valve closed, without lighting, test
all connections with soapy water. If bubbles appear, gas is leaking and torch must be repaired or replaced. Never use a
flame to check for leaks. Make this test in a well ventilated and spark-free area and where there are not open flames.
Burn tip
Hose
Burn tube
N Torch Body
Run-Lock Button ¿area
Ignition
Button y Adjustment
Knob
Connect à à
To Cylinder *
IMPORTANT
1.
Placing belt clip on correct side of waist will enable you to quickly, and naturally, release cylinder from holster
in an emergency.
2. When the cylinder is in the holster, do not move about vigorously or hit the cylinder.
3. When using a support other than your belt, do not permit the cylinder to be pulled by “stretching” the hose.
DO NOT DISCARD THESE WARNINGS AND INSTRUCTIONS
200 Old Wilson Bridge Road
Columbus, OH USA 43085 06/24/15
(866) 928-2657
worthingtoncylinders.com | bernzomatic.com
LIGHTING AND OPERATION
Remove torch from holster tube.
Open regulator valve fully by turning adjustment knob counter clockwise until it stops. Do not force. Always fully open
valve when lighting to prevent damage to ignition system. Never look into the burner tube or point in unsafe direction.
Point torch in a safe direction and pull ignition button. Repeat if necessary while adjusting the valve slightly.
After the torch lights the flame may be adjusted.
To adjust flame, turn the adjustment knob to the required setting. When using propylene fuel gas, turn adjustment knob
to the full “on” position. Do not force. When using propane, turn the adjustment knob to the full “on” position and back
off approximately one-half (1/2) to one (1) full turn.
6. After use, make sure the regulator valve is closed by turning adjustment knob fully clockwise until it stops.
Do not force.
Do not use torch with the gas cylinder tipped more than 60 degrees from its upright position as this may cause torch to
flare. The torch has a built in regulator that controls pressure and reduces the risk of pulsating or yellow flames when
used other than upright. It is recommended to start working with a disposable hand torch cylinder at room temperature
and to keep torch upright as much as possible.
TO ENGAGE LOCK
1. To engage flame lock feature, with ignition button depressed, press the lock button down. Do not force.
2. While holding lock button down, release the ignition button.
TO DISENGAGE LOCK
1. To release flame lock, pull trigger on ignition button until lock releases.
A ADDITIONAL WARNINGS
NS N
N
e Make sure the torch is cool before lighting or removing burner head or before installing or removing accessories.
e (Check all joints and couplings periodically to insure against loose connections. With valve open, without lighting, test all
connections with soapy water. If bubbles appear, gas is leaking and torch must be repaired. Never use a flame to check
for leaks. Make this test in a well ventilated and spark-free area and where there are no open flames.
e In cold weather the size of the flame will be smaller. To produce a larger flame, pre-warm the cylinder to room
temperature prior to use.
STORAGE
REMOVE CYLINDER FROM TORCH WHEN NOT IN USE
1. Turn ignition button to the off position. Make sure regulator valve is closed by turning flame adjustment knob fully
clockwise until it stops. Do not force.
When torch is cool, disconnect cylinder and store torch and cylinder separately and out of reach of children.
Observe cautions on cylinder label.
Do not expose cylinders to temperatures in excess of 49°C (120°F).
Store cylinders in well ventilated areas.
= N
DO NOT DISCARD THESE WARNINGS AND INSTRUCTIONS
200 Old Wilson Bridge Road
Columbus, OH USA 43085 06/24/15
(866) 928-2657
worthingtoncylinders.com | bernzomatic.com
">
