5 ft. x 15 ft. x 6 ft.

Configuration

ITEM #0476087

CHAIN LINK PET KENNEL

MODEL #830063

10 ft. x 10 ft. x 6 ft.

Configuration

ATTACH YOUR RECEIPT HERE

Purchase Date

Questions, problems, missing parts?

Before returning to your retailer, call our customer service department at 1-800-576-2367, 8 a.m. - 6 p.m., EST, Monday - Friday.

Reach us by email at [email protected]

1

PACKAGE CONTENTS

Fig. 1

D

C

D

B

D

C

D

10 ft. x 10 ft. x 6 ft.

Configuration

A

D

B

D

C

D D

D

C

D

D

B

H

F

D

D

D D

G

E

Fig. 2

D

H

E

D

F

D

D

C

D

D

B

D

D

A

C

D

D

D

C

B

D

C

D

D

D

B

D G

PART DESCRIPTION

A Chain Link Fabric Roll

B Corner Post

C Intermediate Post

D Horizontal Rails

E Gate Panel

F Gate Post

G Tension Rods

H Corner Post With Gate Latch

QUANTITY

1

3

4

16

1

1

2

1

NOTE: Gate latch is pre-installed, please do not remove.

2

HARDWARE CONTENTS

AA BB CC

Steel

Wire Tie

Qty. 80

Gate Clips

Qty. 10

Steel Wire Clips

Qty. 22

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. This kennel can be built in two configurations: 10 ft. x 10 ft. or 5 ft. x 15 ft.

Estimated Assembly Time: 2 Hours

Two people are recommended to assemble this kennel.

Tools Required for Assembly (not included): #2 Phillips Screwdriver, 9/16 in. Wrench, Pliers

Choose the site for your kennel. The location should be flat, level and suitable for pets. Choose location of door before you start to build kennel.

ASSEMBLY INSTRUCTIONS

1. Gather the corner and intermediate posts (B & C) and

gate post (F). Each post is labeled with a removable

sticker as the bottom of the post, for easy

identification. Loosen the pre-assembled screws in

the connectors to make insertion of horizontal rails

(D) possible. Do not remove screws, just loosen.

Note: Bottom of posts have 1 in. extension.

Pro Tip: For ease of assembly, we suggest you

lay the posts and rails out on the ground in a

manner that corresponds to the exploded view of

your chosen configuration, either Fig. 1 (10’ x 10’)

or Fig. 2 (5’ x 15’).

1

B

See Label on Posts

C

F

H

3

ASSEMBLY INSTRUCTIONS

2. Assemble gate (E) and gate post (F). Start by

removing the gate keeper screw from the top hinge

tube on the gate post (F). Insert the top of the gate

into the hinge tube and push in as far as it can go.

Then, guide the bottom of the gate onto the bottom

hinge tube. Push gate back downward to sit on the

bottom hinge tube. Re-install the gate keeper screw

to capture the gate.

Note: The gate post (F) is designed to allow the

horizontal rails (D) to slide through the tubes.

2

E F

3. Lay the assembled gate on the ground and slide

horizontal rails (D) through the tubes on the

gate post (F).

Note: Bottom of posts have 1 in. extension.

3

E

4. Slide the top and bottom horizontal rails into corner

post (H) and then slide on an intermediate post (C)

on right.

Note: If you are building a 5 ft. x 15 ft. then you will

use a corner post (B) at the right end of the

horizontal rails (D).

4

H

H

D

F

D

D

F

D

D

D

C

F

D

C

F

4

ASSEMBLY INSTRUCTIONS

5. Working toward the right, slide another set of

horizontal rails (D) into the intermediate post (C)

and then a corner post (B) to the right.

NOTE: Adjust your use of corner posts (B) and

intermediate posts (C) depending on which

configuration you are building, following the

exploded view shown earlier.

6. Tighten the screws on all corner (B&H), gate (F) and

intermediate posts (C). It is important to leave 2 inches

space between the swinging side of gate and the post

for proper latch function. This will complete the gate

side. Carefully stand the completed panel up.

6

H

5

D

DD

B

D

C

D

B

D

C

E

F

H

2 in.

E

C

7. Insert top and bottom horizontal rails (D) into the

corner posts to start the side of kennel, then into

an intermediate post (C). Then, another set of

horizontal rails (D) and then a corner post (B).

This will complete the right side of the kennel frame.

Note: If you are building in the 5 ft. x 15 ft.

configuration, repeat the process with two more

horizontal rails and another intermediate post.

Repeat this process to complete the left side of

the kennel.

7

D

C

C

D

B

D

D

D

5

ASSEMBLY INSTRUCTIONS

8. Complete the rear of the kennel with the addition

of four horizontal rails (D) and an intermediate post (C).

Tighten all screws in all connectors.

Note: If you are building in 5 ft. x 15 ft., only two

horizontal rails are needed to complete.

8

D

D

B

B

D

C

D

B

9. With two people, lift the chain link fabric roll (A)

up into a standing position and drop a tension rod (G)

into the end links and connect to the gate post (F) with

five gate clips (BB) evenly spaced. Unroll the fabric

around the kennel frame.

Use wire ties (AA) to secure fabric to the top of the

kennel frame (D) to keep it in place. Ties can be

loosely applied and then tightened after the fabric is

fully unrolled.

9

B

G

G

BB

D

AA

D

D

A

B

D

D

10. To insure the tightest fit of the fabric, it

is suggested to pull the fabric as tight as possible

at each vertical member and apply three wire clips

(CC) to hold in place as one person is tensioning

the fabric.

Doing this as the fabric is unrolled, at all 7 of the

vertical members will assist in making the final

length determination and a tight fit of the chain link

fabric.

10

C

CC

D

A

6

ASSEMBLY INSTRUCTIONS

11. Chain link fabric (A) is cut to size but may need

to be shortened for exact fit. You may need to

“cut” the fabric by removing a wire. When the

fabric is fully unrolled and the ties have secured

the fabric to the vertical members for tightness,

you should assess the remaining length and

whether the fabric will need to be shortened.

Insert the drop rod (G) into the fabric and with the

help of the Gate Clips (BB) pull the fabric toward

the final vertical and determine if there is excess

length and measure to see how much will need to

be removed for proper fit. Removing one wire will

result in a shortening of approx. 1-3/4". Using pliers,

unlock the knuckles at the top and bottom of wire

to be removed.

Then, twist the wire out from the top.

Remove the appropriate number of wires, without

removing too many. Close the knuckles with pliers.

Drop a tension rod (G) in the last diamonds of the

fabric and stretch it tight. Connect to post with five

gate clips (BB). Fasten fabric with wire ties (AA).

Place ties around bottom of kennel at 12 in. intervals.

Place ties around top at 18 in. intervals.

Expect to use about 31 of the wire ties to secure the wire ties to hold the bottom of the fabric tight.

Note:

11

A

BB

G

A

BB

7

WARRANTY

ONE YEAR LIMITED WIRE KENNEL WARRANTY

What is Covered

The manufacturer warrants that the kennel will be free from defects in workmanship for a period of one (1) year. This warranty is extended only to an original purchaser who installed the product at a residence (not commercial premises) in the 50 United States. It is not transferable.

If a defect exists, the manufacturer will, at its option, either repair or replace the product or the defective component. This warranty does not cover the costs of labor to remove a defective product or component or install any replacement product or component.

This warranty shall not apply to defects or damages caused by mishandling, improper installation or installation not in accordance with the instructions provided with the product, alteration, removal or re-installation, improper or unreasonable use, maintenance or storage, use of incompatible accessories, accident, impact by foreign objects, fire, acts of God or normal wear and tear.

No person is authorized to extend or otherwise modify this Warranty.

How to Obtain Warranty Service

To obtain warranty service, call 1-800-576-2367, 8 a.m. - 6 p.m., EST, Monday - Friday.

Limitations

THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXCEED THE

WARRANTY PERIOD PROVIDED HEREIN.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE BREACH OF ANY WRITTEN OR IMPLIED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have the other legal rights which vary from State to State.

8

Printed in China