Hauslane 3P-GE2L-BFSB 30-in Ducted Stainless Steel Undercabinet Range Hood Use and Care Guide

Hauslane 3P-GE2L-BFSB 30-in Ducted Stainless Steel Undercabinet Range Hood Use and Care Guide
Model UC-PS10SS-30
Table of Contents
Safety Information.................................... 2
Warranty Information............................... 3
Specifications............................................ 4
Parts Included........................................... 4
Tools Needed........................................... 4
Satisfied With It........................................................
2. Jack Up the Hood...................................................
3. Screw It Into Place...................................................
4. Double-Check Installation & Remove Support...
5. Connect Damper & Check for Airtightness.........
6. Plug the Range Hood In.........................................
7. Reinstall Baffle Filters..............................................
8. Keep This Manual....................................................
7
7
7
7
7
8
8
8
Preparation: What to do before
installation................................................. 5
How to Use Your Range Hood................ 8
1. Read This Manual and Gather Tools & Parts.......
2. Remove Packaging.................................................
3. Ensure There is Proper Height Clearance...........
4. Check Your Power Supply and Ducts..................
5. Remove the Baffle Filters.......................................
6. Figure out Duct Requirements & Install Adapter
7. Prepare the Cabinet (Soffit)...................................
8. Find a Helper...........................................................
Basic Maintenance Instructions............... 9
5
5
5
5
5
5
5
5
1.Using the Front Control Panel................................ 8
1. Maintaining the Baffle Filter................................... 9
2. Maintaining the Lighting........................................ 9
3. Cleaning Your Range Hood................................... 9
Troubleshooting Tips.............................. 10
Contact Hauslane.....................................11
How to Install Your Range Hood............ 7
1. Thoroughly Inspect the Unit & Ensure You Are
Safety Information
Before installing your range hood, read the entire instruction
manual. Installers, leave this manual with the homeowner.
WARNING
SUITABLE FOR USE IN HOUSEHOLD COOKING AREA ONLY.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR
INJURY, OBSERVE THE FOLLOWING:
1. Use this range hood only in the manner intended by the
manufacturer. If you have the questions, contact Hauslane
at 1-800-929-0168 or email at [email protected]
2. Before servicing or cleaning, switch power off at service
panel and lock service panel to prevent power from being
switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
qualified personnel in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel-burning
equipment to prevent back drafting. Follow the heating
equipment manufacturer's guidelines and safety standards
such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE),
and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with any solid-state speed control
device.
8. To reduce the risk of fire, use only steel ductwork.
UC-PS10 USER MANUAL
9. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE:
1. Never leave surface units unattended at high settings.
Boil overs cause smoking and greasy spillovers that
may ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or
when cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate
for the size of the surface element.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet
or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. IF THE FLAMES DO NOT GO OUT
IMMEDIATELY, EVACUATE AND CALL THE FIRE
DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN as you may be
burned.
3. DO NOT USE WATER, including wet dishcloths or
towels. This could cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you know
how to operate it.
B. The fire is small and contained.
C. The fire department has been called.
2
D. You can fight the fire with your back to an exit.
4. Two to three installers are recommended because of
the larger size and weight of this hood.
*Based on "Kitchen Fire Safety Tips" published by NFPA.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. To avoid damage and noisy and/or unbalanced impellers,
keep drywall/construction dust, etc. off power unit.
3. Mount your range hood so that the bottom of the hood is
24" to 30" above the cooking surface. The minimum hood
distance above cooktop must not be less than 24"; any
installation less than 24" may cause overheating and cause
damage to the range hood, HAUSLANE does not warrant
this improper installation.
5. To reduce the risk of fire and to properly exhaust air, be
sure to duct air outside. Do not exhaust air into spaces
within walls and ceiling or into attics, crawl space or
garages.
6. Because of the high exhausting capacity of this hood,
you should make sure enough air is entering the house
to replace exhausted air by opening a window close to
or in the kitchen.
7. Use with approved cord-connection kit only.
8. Please read product specification label on range hood
for further information and requirements.
Warranty Information
This range hood is warranted to the original purchaser to be
free of defects in material and workmanship for two (2) years
from the date of purchase.
Our obligation shall be limited to the repair or replacement of
a unit (at our discretion) that may prove, by our sole examination, to be defective under normal use and service during the
warranty period. We may issue credit in the amount of the
invoice value of the defective product (or a percentage of it
according to use) in lieu of repair or replacement. Any failure
of this product that is not traceable to a defect in material or
workmanship is not covered by this warranty. These non-warrantable items include, but are not limited to:
Any defects or damage to light bulbs
Change in color or finish due to chemical usage
Improper installation not in accordance with the instructions
Dents, bumps, and scratches incurred during shipping,
handling, or installation
Damage caused by failure to follow care and cleaning
guidelines, including damage caused by the use of abrasive
cleaners
Alterations made to the unit by the purchaser or installer
Damage caused by accidental impact, fire, flood, freezing,
and normal wear
Bends and warping caused by forced connections,
over-tightened fittings, and inadequate support during
installation
A thorough inspection must be made before installation and
any damage must be promptly reported. We will not be liable
for failures or damage that could have been discovered or
avoided by proper inspection and testing prior to installation.
following the instructions.
Under no circumstance shall we be held liable for
personal injury or property damage resulting from
improper installation or use of this product. We will not
be held liable for inconvenience caused by loss of use of
this product, costs incurred for labor or materials, removal
and installation of replacement units, or any other
incidental or consequential damages. Costs relating to
obtaining access for repair or replacement are the
responsibility of the user.
This warranty does not extend to commercial and
institutional installation or use.
Warranty Claim Procedure
If a claimable defect occurs, please contact our customer
service team at 1-800-929-0168 (8 a.m. - 5 p.m., PST,
Monday - Friday). or email us at [email protected]
Before you make your claim call, please ensure that you
have:
Description of the range hood
Proof of sale
Details regarding the defect
Name(s) and address(es) of the owner and installer
Claims must be filled out in writing and returned within six
(6) months of the appearance of a defect. Failure to
comply with this stipulation will make this warranty null
and void. We reserve the right to a thirty-day (30) delay
following the receipt of a claim in which to inspect the
product. We assume no responsibility for labor costs,
removing or replacing a previously installed product,
transportation, or the return of a product.
Incidental repairs that would involve a minimum of time and
effort on behalf of the purchaser will not be considered
warranty work and no compensation will be deemed forth
coming.
This warranty is non-transferable and shall be voided if the
unit is removed from its initial installation or if it is not installed
UC-PS10 USER MANUAL
3
Specifications
Dimentions UC-PS10SS-30
29.75” W
21.25” D
8”H
Volts
Hertz
Fan CFM
Speeds
Light Wattage
Stainless Steel Grade
120
60
900
3
2W (LED)
430
Package Contents
1 Hood
3 Grease Collector
5
User Manual
2 Round Adapter
4
6
Bag of screws
4 x Under-cabinet mounting screws
3 x Outlet adapter mounting screws
3 x Baffle Filters (Preinstalled)
2
1
5
6
4
3
Tools Needed
Before you begin the installation process, gather the following tools:
9
4
3
1
5
6
7
10
8
2
11
Electric Drill & Extended
length head driver bit
12
4 Philips Screwdriver
7 Hammer
10 Safety Goggles
2 Safety Gloves
5 Flathead Screwdriver
8 Adjustable wrench
11 Measuring Tape
3 Pencil
6
9 Level
12 Aluminum Foil Tape
1
UC-PS10 USER MANUAL
Needle nose pliers
4
Preparation: What to Do Before Installation
Before installing your range hood, carefully follow these steps:
1. Read This Manual
Read through all the steps. If you fail to read the instructions
carefully, we will not be responsible for damages incurred on
your part. If you’re not confident in your abilities to install the
range hood properly, we recommend hiring a certified
technician to complete the installation. While reading through
the manual, ensure you have the necessary tools and parts
according to the previous page.
2. Remove Packaging
Remove any packaging, including the plastic wrap and
protective plastic film, from the hood. You can use stainless
steel cleaner to wipe down the surface if desired. Keep all
packaging materials until you are satisfied with our product.
3. Ensure There is Proper Height Clearance
Check that you’ll be able to install the UC-PS10 Range Hood
at the correct height. To ensure the best performance, the
bottom of your range hood must be between 24” and 30”
from the top of the cooking surface. For gas ranges, the
required distance is 30”.
5. Remove the Baffle Filters
Remove the three baffle filters from the range hood by
pulling the levers out and slowly removing them. Set them
aside.
6. Figure Out Ducting Requirements & Install Adapter
This range hood requires ducting to the outside for
ventilation. It is made to work with 6” exhaust ducts. For
vertical ducting, you’ll need to attach the vertical 6” round
adapter and fasten it with two the outlet mounting screws
(BB).
Do not exceed the maximum height of 30" while in operation.
This is very important! Installing at the incorrect height could
lead to drastic reduction in the range’s performance or even
cause a fire.
4. Check Your Power Supply and Ducts
Check to ensure your main voltage is in line with the required
voltage outlined on the rating plate inside this hood. Also
check the domestic power supply to guarantee adequate
earthing before installation.
This range hood must be ducted to the outside. Don’t
connect the range hood to exhaust ducts that carry any type
of combustion fumes like fireplaces, boilers, or any similar
items. The vents should have a short, straight run to the
outside. Avoid any elbows if possible, and if an elbow is
required, a minimum of a 12” straight run is imperative before
the elbow.
Roof
Duct(for vertical
discharge)
Cabinet
24”-30”
from cooking surface
7. Prepare the Cabinet (Soffit)
Measure the size of the outlet adapter relative to the
cabinet. If it is not already done, you’ll need to cut an
opening in the cabinet to ensure the outlet adapter and
power cable can pass through. If you must do this, use a
pencil and ruler to mark the area, then cut with a wall/keyhole saw.
If you’re installing the UC-PS10 under a cabinet with a
recessed bottom, we recommend using 4” wood fillers on
each side to stabilize the cabinet for mounting purposes.
8. Find a Helper
This range hood is best installed by two or more people
due to its size and weight. Again, it is recommended to
hire a certified technician for installation to reduce the risk
of damage or injury.
UC-PS10 USER MANUAL
5
Preparing the Cabinet
Cabinet with recessed bottom
Cabinet or soffit with flush bottom
30” cabinet (typical)
30” cabinet (typical)
Cabinet with
recessed bottom
Cabinet with
flush bottom
1
1
7”x7”
Opening
4-3/4”
7”x7”
Opening
1” hole
12-3/4”
4-3/4”
1” hole
12-3/4”
2”
2”
2”
2”
3-1/8”
3-1/8”
Four, (4)
mounting holes
2
1-7/8”
Four, (4)
mounting holes
1-7/8”
26”
3”
7”x7”
Opening
26”
4-1/4”
1” hole
12-3/4”
2”
2”
3-1/2”
wide filler
along front
and sides
3”
7”x7”
Opening
4-1/4”
1” hole
12-3/4”
2”
2”
1-1/2”
RH filler notched
at back corner to
allow plug clrearance
UC-PS10 USER MANUAL
3-1/8”
3-1/2”
wide filler
along front
and sides
1-1/2”
3-1/8”
6
How to Install Your Range Hood
When you’ve completed all the preparation steps, you’re
ready to install your range hood.
1. Thoroughly Inspect the Unit and Ensure You Are Satisfied
With It
Check your range hood for damaged or missing parts. Plug it
in to an outlet to ensure the fan and lights work. If anything is
damaged or missing, contact the manufacturer to get the
issues solved. Don’t throw away packaging until you’re sure
you are fully satisfied with the product.
IMPORTANT: Power the range hood and test all functions
before proceeding with the installation. If the range hood is
not working properly, please contact us immediately
(1-800-929-0168 / [email protected]).
2. Jack Up the Hood
If you are not removing the range, place the plywood (30” x
24”) over the range / cooktop to avoid possible damage. Put
the cabinet jacks on the plywood and place the second piece
of plywood over the two cabinet jacks. Using the cabinet
jacks, lift the hood into its position under the cabinet. Ensure
that the adapter and power cord enter the cabinet openings
and that the power cord is not pinched between the hood
and the cabinet.
If you do not wish to use a cabinet jack, you will need three
people. Have two helpers holding the range hood in place
while the third person inserts the screws to mount the range
hood. For cabinet jack operation, please refer to its manual.
AA
4. Double-Check Installation and Remove Support
Be sure that the hood is securely attached before removing the cabinet jacks and plywood.
5. Connect Damper & Check for Airtightness
Double-check to make sure that the adapter has entered
the ductwork properly. Then, make sure the damper
opens and closes freely. This will ensure better and
quieter performance. Finally, ensure the duct is firmly
attached to the adapter and wrap the joint with aluminum
foil tape to make it air-tight.
IMPORTANT: Always fully open the damper. A
half-opened damper will lead to backdraft, meaning air
will back-flow through the hood into the kitchen.
3. Screw It Into Place
From the bottom of the hood, carefully insert the mounting
screws (AA) with washers into each of the pre-drilled mounting holes in the range hood. Start with the front left, then front
right.
After the screws are in place for the front mounting holes,
work on the rear left, then rear right.
TIP: To easily reach the rear mounting holes, use an extension
tool for the power drill.
UC-PS10 USER MANUAL
7
6. Plug the Range Hood In
Plug the power cable into an outlet.
6. Reinstall Baffle Filters
Reinstall the three baffle filters.
7. Keep This Manual
Put this manual in a safe place and keep for further
reference.
How to Use Your Range Hood
Now that your range hood is installed, it’s time to learn how to
use it. It is very simple to use and is operated entirely using
the front control panel.
3
2
1
4
5
6
7
1- LOW SPEED FAN
2- MEDIUM SPEED FAN
3- HIGH SPEED FAN
4- CLOCK
5- TIMER DELAY
6- LIGHT
7- ON/OFF
How to Set the Fan Speed
Press (1) for low speed, (2) for medium speed, and (3) for high
speed.
How to Turn Light On/Off and Adjust Intensity Levels
This range hood has energy-efficient LED lighting with two
light intensity levels. Press the light button (5) to turn the light
to a low intensity. Press the light button (5) again to use the
higher intensity. Press it a third time to turn the light off.
How to Set the Timer Delay
This range hood has a timer delay button that comes in handy
if you need to use your hood for a set period of time. While
the range hood is running, press the timer delay button (6). It
starts with 3 minutes, and with every touch, it will increase by 1
minute up to 7 minutes. When you release the button, it will
flash 3 times and the timer will be set.
UC-PS10 USER MANUAL
8
Basic Maintenance Instructions
Your range hood requires some easy routine maintenance to
keep it running efficiently.
Maintaining the Lighting
This range hood uses two lamps of 2W.
Maintaining the Baffle Filter
Clean the grease filters frequently—we suggest cleaning every
2 weeks. For your convenience, the filters are dishwasher safe!
1. Turn off power or unplug the range hood before
removing bulbs.
1. Remove all three baffle filters by pulling the levers and
slowly taking the filters down.
2. Remove the baffle filters.
3. Disconnect the wire that connects the lights to the
hood.
4. Apply pressure from the inside and push the entire light
housing out.
5. Replace with new light bulb. Insert the light in the
socket, then connect the wire.
6. Replace the baffle filters and plug the range hood back
in.
2. Clean the baffle filters with warm water and detergent, or
place them in the dishwasher. Be careful with the filters to
avoid damage; do not bend them.
Cautions: Please unplug the power cord of the range
hood before proceed to replace the light bulb.
3. Let the baffle filters dry completely.
4. Reinstall the baffle filters.
Cleaning Your Range Hood
This range hood will look great and function correctly for a long time with proper care. Here are a few do's and dont's when
caring for your range hood.
WARNING: Failure to maintain basic standards of care and cleaning will increase the risk of fire.
DO
Clean the range hood with warm, soapy cloth or a
stainless-steel polish.
Clean the hood in line with the grain of the stainless steel.
DONT
Don’t use cleaners or cloths that are corrosive or abrasive.
Don’t use detergents with ingredients like chloride, iodide,
or fluoride.
Don’t leave dirt or soap residue on the hood. This can
damage the surface. Wash the hood’s surface and rinse
immediately with clean water.
After cleaning with soap, rinse with clean water and wipe with Don’t let particles, especially construction particles (from
a clean, dry cloth.
sanding, etc.) enter the hood. Cover the hood during room
renovations.
Check the ducts and vents regularly to make sure they are not Don’t use flammable agents near the stove, as these can
clogged.
cause explosions.
UC-PS10 USER MANUAL
9
Troubleshooting Tips
WARNING: Please turn off the power circuit or power breaker panel before troubleshooting this range hood. Failure to do
so can cause death or serious injury.
Problem
My range hood won’t work.
My range hood vibrates while the fan is operating.
The fan is operating weakly.
The fan is not working properly even though the lights are
working.
The vent hood is not working efficiently.
The light is not working.
Solution
1. Make sure the power supply and wiring are connected
securely.
2. Double-check to see that the power breaker is on and
the power supply is live.
3. Check to see that the control panel cables are connected correctly to the switchboards.
1. Check to ensure the hood is firmly secured to the
cabinet/wall. Tighten or add screws if necessary.
2. Confirm that the motor is firmly in place and secured
safely. If it is not, tighten it.
3. If those steps haven’t resolved the issue, your fan may
be damaged. If it is damaged, you may need to replace it.
1. Double-check to ensure the duct size is correct.
2. Clean ducts or filters if they’re dirty. Also, check to make
sure the mesh enclosure on the hood is receiving proper
air ventilation.
3. If possible, check to see that the damper is functioning
properly regarding the opening.
1. Double-check that the fan is not jammed /that it isn’t
scraping any of the surfaces of the hood.
2. If this doesn’t work, you may need to replace the motor
as it may be defective.
1. The minimum distance between the cooking area and
the appliance should be 24" or 30" maximum. Check to
see if this is correct.
2. Make sure that the duct is not susceptible to easy wind
opening.
3. Make sure the fan speed is at the appropriate rate. The
heavier the cooking, the greater the speed of the hood
should be set.
4. Closing the windows and doors in the room will allow
the vent to work much better.
5. As noted during the installation process, all ductwork
must be done correctly. You may need to reduce the
length of ductwork or reduce elbows.
6. Make sure all joinery in ductwork is sealed and secured
properly.
1. Check to see if lightbulb is loose and needs to be
tightened.
2. If tightening doesn’t fix the problem, replace bulb with a
new one and see if that solves the issue.
3. If replacement and/or tightening does not solve, you
may need to replace the lighting service system on the
hood.
Still experiencing problems after following these steps? Contact a technician to assist. Contact us at 1-800-929-0168 or
[email protected]
UC-PS10 USER MANUAL
10
Contact Hauslane
Extended Warranties
If you are interested in an extended warranty, sign up on our website at www.hauslane.com
Parts and Accessories
If you need replacement parts or accessories, visit www.hauslane.com
Contact Us
We’d be happy to answer your questions or resolve any issues you may have.
Phone: 1-800-929-0168
Find Us and Connect with Us
UC-PS10 USER MANUAL
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement