Samsung NK36R5000WS Convertible Stainless Steel Wall-Mounted Range Hood Use and Care Guide

Samsung NK36R5000WS Convertible Stainless Steel Wall-Mounted Range Hood Use and Care Guide
Range Hood
Hotte de la cuisine
Campana de cocina
Installation Instructions Guide
Guide d’instructions d’installation
Guía de Instrucciones para Instalación
NK36R5000WG/AA, NK30R5000WG/AA, NK36R5000WS/AA, NK30R5000WS/AA
LIB0154965
Table of Contents
Table of Contents
2
Important Safety Instructions
3
Installation Requirements
4
Electrical Requirements
4
Before Installing the Hood
4
Venting Methods
4
Tools and Parts
5
Dimensions and Clearances
5
Installation
6
Installation Instructions
6
Install the Range Hood
7
Install Duct Covers
8
Electrical Connection
8
Range Hood Use and Care
9
Description of the Hood
9
Control
9
Maintenance
9
Accesories
10
Range Hood for ADA Compliance
11
Warranty (USA)
12
Warranty (Canada)
13
English
Important Safety Instructions
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
■■ When cutting or drilling into the wall or ceiling; do not damage
electrical wiring and other hidden utilities.
PLEASE READ ENTIRE INSTALLATION GUIDE BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
CAUTION
To reduce the risk of fire and to properly exhaust air, be sure to duct air
outside - do not vent exhaust air into spaces within walls or ceilings, or
into attics, crawl spaces or garages.
WARNING
IMPORTANT:
Important Safety Instructions
Save these Instructions for the Local Electrical
Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for
the owner.
OWNER: Please retain these instructions for future
reference.
■■ Ducted fans must always be vented to the outdoors.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
Symbols used in this manual
WARNING
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may result in electric shock, personal
injury, or property damage.
NOTE
Useful tips and instructions
These warning icons and symbols are here to prevent injury to you and
others.
Please follow them explicitly. After reading this section, keep it in a safe
place for future reference.
WARNING
Turn off the power circuit at the service panel and lock
out panel before wiring this appliance.
Requirement 120 VAC, 60 Hz. 15 or 20 A Branch Circuit
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
■■ Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
■■ Always turn the hood ON when cooking at high heat or when flambeing
food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
■■ Clean ventilating fans frequently. Grease should not be allowed to
accumulate on the fan or filter.
■■ Use proper pan sizes. Always use cookware appropriate for the size
of the surface element.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING
PRECAUTIONS:a
■■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
■■ NEVER PICK UP A FLAMING PAN - you may be burned.
■■ DO NOT USE WATER, including wet dishcloths or towels a violent steam explosion will result
■■ Use an extinguisher ONLY if:
- You know you have a class ABC extinguisher, and you already know
how to operate it.
– The fire is small and contained in the area where it started.
– The fire department is being called.
– You can fight the fire with your back to an exit.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING PRECAUTIONS:
■■ Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer.
■■ Before servicing or cleaning the unit, switch the power off at the
service panel and lock the service panel to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag to the service panel.
■■ Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction.
■■ Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent backdrafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), the American Society
for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),
and the local code authorities.
a
Based on “Kitchen Fire Safety Tips” published by NFPA.
WARNING
To reduce the risk of fire or electrical shock, do not use this fan with any
solid-state speed control device.
WARNING
Do not let children near this appliance. Do not let children play with this
appliance.
Keep all packaging materials out of children’s reach. Properly dispose the
packaging materials after this appliance is unpacked.
NOTE
Suitable for use in household cooking area.
Read and save this instructions
English
3
Installation Requirements
Electrical Requirements
Venting Methods
IMPORTANT
Observe all governing codes and ordinances.
Closely follow the instructions set out in this manual. Samsung is not
responsible for any eventual inconveniences, damages or fires caused by
not complying with the instructions in this manual.
Installation Requirements
It is the customer’s responsibility:
■■ To contact a qualified electrical installer.
■■ To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
— latest edition*, or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all
local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended
that a qualified electrician determine that the ground path is adequate.
A copy of the above code standards can be obtained from:
Ducting version
The hood is equipped with a 6” (15.2 cm) round transition for discharge of
fumes to the outside.
Horizontal Discharge
Vertical Discharge
Horizontal Discharge
A
B
B
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
A
B
A
Other Requirements
■■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.
■■ If the house has aluminum wiring, follow the procedure below:
1. Connect a section of solid copper wire to the pigtail leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools designed
and UL listed for joining copper to aluminum.
■■ Follow the electrical connector manufacturer’s recommended
procedure. Aluminum/copper connections must conform with
local codes and industry accepted wiring practices.
■■ Wire sizes and connections must conform with the rating of the
appliance as specified on the model/serial rating plate. The model
serial plate is located behind the filter on the rear wall of the range hood.
■■ Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards
C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.
■■ A U.L.- or C.S.A.-listed conduit connector must be provided at each
end of the power supply conduit (at the range hood and at the
junction box).
Before installing the Hood
4
••
The Vent system must terminate outdoors.
••
For the most efficient air flow exhaust, use a straight run or as few
elbows as possible. CAUTION: Vent unit to outside of building, only.
••
At least two people are necessary for installation.
••
Fittings material are provided to secure the hood to most types
of walls and ceilings. Consult a qualified installer to confirm that
the fittings are suitable for your cabinets, walls, and ceiling.
••
Do not use flexible ducting.
••
COLD WEATHER installations should have an additional backdraft
damper installed to minimize backward cold air flow and a
nonmetallic thermal break to minimize conduction of outside
temperatures as part of the ductwork. The damper should be on the
cold air side of the thermal break. The break should be as close as
possible to where the ducting enters the heated portion of the house.
English
A. Wall cap
B. 6” (15.2 cm) round vent
A. Roof cap
B. 6” (15.2 cm) round vent
A. Deflector
B. 6” (15.2 cm) round vent
Preparation
Do not cut a joist or stud unless absolutely necessary. If a joist or stud
must be cut, then a supporting frame must be constructed.
Fittings material are provided to secure the hood to most types of
walls/ceilings.
However, a qualified technician must verify that the fittings are suitable
for your cabinets, walls, and ceiling.
Before making cutouts, make sure there is proper clearance within the
ceiling or wall for the exhaust vent.
Ductless version (Recirculating)
For installations where cooking fumes and vapor cannot be discharged
to the outside, attach a charcoal filter and the deflector to the duct cover
support bracket. Fumes and vapors will be recycled through the top grille
by a duct connected to the transition and the transition mounted on the
deflector.
NOTE
For horizontal discharge only: purchase the Ductless Recirculating Kit.
Minimum Duct Size: 6” Round Pipe.
CAUTION
■■ For electric/induction cooktop & range installations: Mount the hood
so the bottom is at least 24” (61cm) above the cooking surface.
■■ For gas cooktop & range installations: Mount the hood so the bottom
is at least 27” (68.6 cm) above the cooking surface.
■■ For both, mount no higher than 36” (91.4 cm) above the cooking
surface.
■■ Measure the mounting height from the surface of the range to the
bottom of the hood.
WARNING
This hood is intended for household use.
PLEASE READ THE INSTALLATION MANUAL FOR THE HOOD´S
SPECIFIC APPLICATION. Check your ceiling height and the hood´s
height before selecting your hood.
Installation Requirements
Tools and Parts
Optional accessories and consumable parts
Removing the packaging
CAUTION
Remove the carton carefully. Wear gloves to protect against sharp edges.
WARNING
Remove the protective film covering the product before putting it into
operation.
Parts supplied
•• Hood assembly with blower and LED lamps already installed.
Hardware bag with:
Part
Qty
6
5x45 mm
5.4x75 mm
3.5x9.5 mm
Part
8x40 mm
Qty
NK30R5000WS
NK36R5000WS
NK30R5000WG
NK36R5000WG
Extension Kit
NK-AE505PWS/AA
NK-AE505PWG/AA
Recirculating
Kit
NK-AF020FNB/AA
Charcoal
Filter
NK-AR040FNB/AA
* Order the needed kit specifying your hood model.
Dimensions and Clearances
F
2
4
4
E
G
10x60 mm
2
Installation Requirements
••
MODEL
1
Duct cover bracket
C
2.9x6.5 mm
1
2
D
Mounting template
2
1
6” round transition
Duct Covers
A
B
Tools/Materials required
••
Level
••
Drill with 1¼” (3.2 cm),1⁄8” (3.2 mm), and 1⁄16” (4.8 mm) drill bits
••
Pencil
••
Wire stripper or utility knife
••
Tape measure or ruler
••
Pliers
••
Caulking gun and weatherproof caulking compound
••
Jigsaw or keyhole saw
••
Metal snips
••
Screwdrivers:
•• Phillips
•• Flat - blade
Parts needed
•• Home power supply cable
••
½” (12.7 mm) UL listed or CSA approved strain relief
••
3 UL listed wire connectors
••
1 wall or roof cap
••
Metal vent system
A
NK30R5000WS
NK36R5000WS
NK30R5000WG
NK36R5000WG
30” (76.2 cm)
36″ (91.2 cm)
B
19 11⁄16″ (50 cm)
C*
Max: 42 1⁄8″ (107 cm)
Min: 28 6⁄16″ (72 cm)
D**
Max: 38 3⁄16″ (97 cm)
Min: 28 6⁄16″ (72 cm)
E
6” (15.24 cm)
F
7 3⁄16″ (18.3 cm)
G
8 3⁄16″ (20.8 cm)
* Ductless (Recirculating) version
** Ducted version
English
5
Installation
Installation Instructions
We recommend that a qualified technician install the range hood. It is
the installer’s responsibility to ensure the range hood complies with the
installation specifications for the product.
••
It is recommended that the vent system be installed before the hood is
installed.
••
Before making cutouts, make sure there is proper clearance within the
ceiling or wall for the exhaust vent.
••
Confirm that all installations parts have been removed from the
shipping carton.
Installation
WARNING
To reduce the risk of fire, electric shock, or injury to persons, observe the
following.
■
Shut off power to the circuit you will be attaching the hood to at the
circuit breaker panel or fuse box.
■
Determine which venting method to use: roof, wall, or nonvented.
■
Select a flat surface for assembling the range hood.
Place a covering over that surface.
Always have 2 or more persons lift or move the range hood.
■
7. Install the 2 - 5 x 45 mm mounting screws. Leave a 1⁄4″ (6.4 mm) gap
between the wall and the back of the screw head to slide the range
hood into place.
1
⁄4″ (6.4 mm)
Vent cover bracket installation
1. Attach the vent cover bracket to the wall flush to the ceiling using 2 5x45mm screws.
A
C
D
B
Mounting the duct cover bracket
1. Determine and mark the centerline on the wall where the canopy
hood will be installed. Shut off power at the circuit breaker panel or
fuse box.
2. Select a mounting height of no less than 24” (61 cm) above an electric
cooking surface or 27” (68.6 cm cm) above a gas cooking surface.
3. Tape the template in place, aligning the template center line and
bottom with the hood center line and hood bottom line marked on
the wall.
A
A. 8 x 40 mm anchors
B. Centerline on wall
C.Vent cover support bracket
D. 5 x 45 mm screws
Complete preparation
1. Determine and make all necessary cuts in the wall for the vent system.
Install the vent system before installing the hood. See “Venting
Requirements” section.
2. Determine the required height for the home power supply cable and
drill a 1¼” (3.2 cm) hole at this location.
3. Run the home power supply cable according to the National Electrical
Code or CSA Standards and local codes and ordinances. There must
be enough ½” conduit and wires from the fused disconnect (or circuit
breaker) box to make the connection in the hood’s electrical terminal
box.
NOTE
Do not turn on power until the installation is complete.
4. Use caulk to seal all openings
B
C
A. Centerline
B. Fastener locations
C. Mounting height reference (hood bottom line)
4. Mark the centers of the fastener locations on the wall by pushing a
pencil point through the template.
IMPORTANT: All screws must be installed into the wood studs or
framing. If there is no wood to screw into, additional wall framing
supports may be required.
5. Remove the template.
6. Drill 3⁄16″ (4.8 mm) pilot holes at all locations where screws are going
to be installed into wood.
6
English
Installation
Install the Range Hood
WARNING
USE TWO OR MORE PEOPLE TO MOVE AND INSTALL THE RANGE
HOOD. FAILURE TO DO SO CAN RESULT IN BACK OR OTHER
INJURY.
1. Mark the lower mounting hole locations with a pencil .
2. Uninstall the hood assembly, and drill 3⁄16”” (4.8 mm) pilot holes at
the marked locations.
For vented installations only
1. Fit the vent system over the exhaust outlet.
2. Measure from the bottom of the air deflector to the bottom of the
hood outlet. Cut the ductwork at the measured dimension.
Roof Outlet
Wall
outlet
Dimension to
measure
3. Hang the range hood again on 2 the upper mounting screws.
4. Level the range hood and tighten the upper mounting screws.
5. Install 2 - 5 x 45 mm lower mounting screws and tighten. Use the
optional wall anchors if needed.
Installation
A
3. Seal the connection with clamps.
B
4. Confirm that the back draft dampers work properly
Install the Duct Covers
When using both upper and lower vent covers, push the lower cover
down onto the hood and lift the upper cover to the ceiling, and then install
with two mounting screws.
NOTE
For vented installations, the upper vent cover may be reversed to hide
slots.
C
C
A. Mounting screws
B. Mounting slots
C. Lower mounting screws
D
C
Connect the vent system
1. Install the transition on top of the hood (if removed for shipping) with
2-3.5x9.5 mm sheet metal screws.
A
E
A
B
A. Vent transition
B. 3.5 x 9.5 mm screw
A.. Upper vent cover
B. Lower vent cover
C. 2.9 x 6.5 mm screws
D. Bracket
English
7
Installation
NOTE
To prevent scratches, lay paper or a kitchen towel over the edges of the
lower flue duct to protect the surface.
Electrical Connection
WARNING
Electrical shock hazard.
WARNING
Shut off power at the circuit breaker panel or fuse box before servicing.
Replace all parts and panels before operating. Failure to do so can result
in death or electrical shock.
WARNING
Electrically ground the blower.
Connect the ground wire to the green and yellow ground wire in the
terminal box. Failure to do so can result in death or electrical shock.
1. Shut off power at the circuit breaker panel or fuse box power.
Installation
2. Remove the terminal box cover.
3. Remove the knockout in the terminal box cover and install a UL listed
or CSA approved 1⁄2” strain relief.
Complete Installation
•• For non-vented (recirculating) installations only, install charcoal
filters over metal grease filter. See the “Mainteinance” section.
•• Install metal filters. See the “Mainteinance” section.
4. Run the home power supply cable through the strain relief, into
the terminal box.
A
E
D
C
B
A. Home power supply cable
B. UL listed wire connectors
C. White wires (N)
D. Black wires (L)
F. Green (or bare) and
yellow-green ground
5. Use UL listed wire connectors and connect the black wires (C)
together.
6. Use UL listed wire connectors and connect the white wires (E)
together.
7. Connect the green (or bare) ground wire from the home power supply
to the yellow-green ground wire (F) in the terminal box using UL listed
wire connectors.
8. Tighten the strain relief screw.
9. Install the terminal box cover.
10. Turn on the power.
To get the most efficient use from your new range hood, read the
“Maintenance” section. Keep your Use, Care, and installation Guide close
to the range hood for easy reference.
8
English
Range Hood Use and Care
Description of the Hood
Maintenance
Cleaning
Do not spray cleaners directly onto the controls while cleaning the Hood.
The hood should be cleaned regularly internally (at least as often as you
clean the grease filter ) and externally. Clean using a cloth dampened
with neutral liquid detergent. Do not use abrasive products.
DO NOT USE ALCOHOL!
5
Range Hood Use and Care
Grease Filter
Traps cooking grease particles. The grease filter must be cleaned once
a month using a mild detergent, either by hand or in a dishwasher,
which must be set to a low temperature and a short cycle. When
washed in a dishwasher, the grease filter may discolor slightly, but this
does not affect its filtering capacity. To remove the grease filter, pull the
spring release handle.
1
2
3
A
4
A. Spring release handle
1. Blower and light controls
2. LED lamps
3. Grease filter handle
4. Grease filters
5. Duct covers
WARNING
Failure to carry out these basic cleaning recommendations for the
hood and failure to clean the grease filter may cause fire risks.
Therefore, we strongly recommend you follow these instructions.
Samsung is not responsible for any damage to the motor or for any
fire damage linked to inappropriate maintenance or failure to observe
these cleaning and safety recommendations.
Control
A
A. Light On/Off
B. Off button
C. Low button
B
C
D
E
Replacing a LED lamp
The LED lights are replaceable by a service technician only. See the
warranty for service contact information.
D. Med button
E. High button
Operating the light
The Light On/Off button (A) controls both lights. Press once
for On and again for Off.
Operating the blower
The Blower OFF button (B) turns the blower off.
The Blower Speed buttons (C,D,E) set the desired speed and control the
sound level for quiet operation. The speed can be changed anytime
during fan operation by pressing the desired blower speed button.
1. To Turn the Blower On, press a Blower Speed button (C,D,E).
2. To Turn the Blower off, press the Blower OFF Button (B).
English
9
Range Hood Use and Care
Accessories
Charcoal filter
For non-vented (recirculating) installation only
The charcoal filter is not washable. It should last up to 6 months
with normal use. Replace with Charcoal Filter Replacement Kit.
NOTE
To reduce the risk of fire or shock when the hood is used in recirculation
mode, use only the conversion kit models listed below:
Recirculating kit: NK-AF020FNB/AA
Charcoal Filter Replacement kit: NK-AR040FNB/AA
To replace charcoal filter:
1. Remove the metal grease filter from the range hood. See “Metal Grease Filter” in this section.
2. Bend the spring clips away from the metal grease filter.
To attach the recirculation kit, follow these steps:
Range Hood Use and Care
1. Assemble the air deflector with the duct cover bracket with 2 - assembly screws provided with the Recirculation Kit.
A
D
B
C
A. Vent cover bracket
B. 2.9 x 6.5 mm screws
C. Deflector
2. Measure from the bottom of the air deflector to the bottom of the hood outlet.
A
B
X
D
C
E
A. Air deflector
B. Vent clamp
C. X = length to cut vent duct
D. Vent duct
E. Exhaust outlet
3. Cut the duct to the measured size (X).
4. Remove the air deflector.
5. Slide the duct onto the bottom of the air deflector.
6. Place the assembled air deflector and duct over the exhaust outlet from the hood.
7. Re-attach the air deflector to the duct cover bracket with 2 assembly screws.
8. Seal the connections with vent clamps
10
English
3. Place the charcoal filter into the top side of metal filter.
4. Insert the metal grease filter back into the range hood.
Range Hood Use and Care
Range Hood for ADA Compliance
Range hoods can be installed to comply with Sections 308 and 309 of
ADA Guidelines, when used with appropriately mounted controls installed
at 15” (38.1 cm) to 40” (101.6 cm) above the floor and control access
does not require reaching over a cooking appliance.
NOTE
All the models can be controlled by only one remote switch (The switch
activates or deactivates the motor and the light of the hood).
WARNING
All electrical work must be done in accordance with local codes,
ordinances, or the national electrical code as applicable. For safety, this
product must be installed in a grounded switch box. The electrical wiring
installation must be done by a qualified technician.
WARNING
Electrical Shock Hazard
Turn off power at the circuit breaker panel or fuse box before servicing.
Replace all parts and panels before operating. Failure to do so can
result in death or electrical shock.
1. MOUNT THE SWITCH BOX . Install a 3½” deepsingle gang switch
box
2. ATTACH THE POWER CABLE. Clamp wiring to the switch box and
unit using an appropriate clamp. Provide 6” leads inside the box and
fan for easier wiring.
3. CONNECT THE WIRING. General instructions:
•• Make sure both the switch box and the appliance are properly
grounded.
•• Make sure the ground wire is securely fastened to the control’s
ground screw. Tighten the ground screw.
•• Use proper wire nut sizes for the number and size of the wires.
•• For push-in and screw terminals: Use min. #14 AWG solid copper
wire only.
•• Tighten the screw terminals.
•• Make electrical connections following the appropriate diagram.
APPLIANCE
N
E
G
(N, ground)
BLACK
WHITE
H
G
(L, ground)
E
D
C
LOAD
GRND
F
A
SINGLE
GANG
SWITCH
BOX
120 VAC
L
POWER SUPPLY HOME
Range Hood Use and Care
The following range hoods NK30R5000WS, NK36R5000WS,
NK30R5000WG, NK36R5000WG can work in an ADA Compliant
situation when the range hood is wired to operate from a dedicated,
standard electrical wall switch. To facilitate this application, share the
information on the following pages with your electrician when preparing
for the installation.
WARNING
To avoid fire or electrical shock, turn off power at the circuit breaker
panel or fuse box. Confirm that the power is off before wiring.
4. MOUNT THE CONTROL IN THE SWITCH BOX. Tuck wires into
the switch box and fasten the control to the box using the attached
screws.
5. ATTACH THE SWITCH PLATE. Fasten the switch plate to the control
using the short screws from the parts bag.
B
A. Range Hood Cable
B. UL listed wire connector
C. White wires (N)
D. Black wires (L)
E. Green (or bare) and
yellow-green ground
F. UL listed switch
G. Home power supply cable
H. Deep single gang switch box
English
11
warranty (USA)
SAMSUNG RANGE HOOD
Limited warranty to original purchaser
This SAMSUNG brand product, as supplied and distributed by
Samsung Electronics America, Inc. (SAMSUNG) and delivered
new, in the original carton to the original consumer purchaser, is
warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:
ONE (1) YEAR PARTS AND LABOR
This limited warranty begins on the original date of purchase,
and is valid only on products purchased and used in the United
States. To receive warranty service, the purchaser must contact
SAMSUNG for problem determination and service procedures.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to SAMSUNG or
SAMSUNG’s authorized service center.
SAMSUNG will repair or replace this product, at our option and
at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited
warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned
to SAMSUNG. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is
longer.
In-home service will be provided during the warranty labor
period subject to availability within the contiguous United States.
In-home service is not available in all areas. To receive in-home
service, the product must be unobstructed and accessible to
service personnel. If during in-home service repair can not be
completed, it may be necessary to remove, repair and return the
product.
This limited warranty covers manufacturing defects in materials
and workmanship encountered in normal, noncommercial use of
this product and shall not apply to the following, including, but
not limited to: damage which occurs in shipment; delivery and
installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage
or exterior finish; accidents, abuse, neglect, fire, water, lightning
or other acts of nature; use of products, equipment, systems,
utilities, services, parts, supplies, accessories, applications,
installations, repairs, external wiring or connectors not supplied
or authorized by SAMSUNG which damage this product or result
in service problems; incorrect electrical line voltage, fluctuations
and surges; customer adjustments and failure to follow operating
instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book;
problems caused by pest infestations, and overheating by user.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE
LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON
SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR
OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE
OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND
EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND
AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG
AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN
THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some provinces or territories may or may not allow limitations on
how long an implied warranty lasts, or the exclusion or limitation
of incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which
vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
1-800-SAMSUNG (726-7864) or
www.samsung.com/us/support
warranty (Canada)
SAMSUNG RANGE HOOD
Limited warranty to original purchaser
This SAMSUNG brand product, as supplied and distributed by
Samsung Electronics Canada, Inc. (SAMSUNG) and delivered
new, in the original carton to the original consumer purchaser, is
warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:
ONE (1) YEAR PARTS AND LABOR
This limited warranty begins on the original date of purchase,
and is valid only on products purchased and used in Canada. To
receive warranty service, the purchaser must contact SAMSUNG
for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service
center. The original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG’s
authorized service center.
SAMSUNG will repair or replace this product, at our option and
at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited
warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned
to SAMSUNG. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is
longer.
In-home service will be provided during the warranty labor
period subject to availability within the contiguous Canada.
In-home service is not available in all areas. To receive in-home
service, the product must be unobstructed and accessible to
service personnel. If during in-home service repair can not be
completed, it may be necessary to remove, repair and return the
product.
This limited warranty covers manufacturing defects in materials
and workmanship encountered in normal, noncommercial use of
this product and shall not apply to the following, including, but
not limited to: damage which occurs in shipment; delivery and
installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage
or exterior finish; accidents, abuse, neglect, fire, water, lightning
or other acts of nature; use of products, equipment, systems,
utilities, services, parts, supplies, accessories, applications,
installations, repairs, external wiring or connectors not supplied
or authorized by SAMSUNG which damage this product or result
in service problems; incorrect electrical line voltage, fluctuations
and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental
instructions that are covered and prescribed in the instruction
book; problems caused by pest infestations, and overheating
by user. SAMSUNG does not warrant uninterrupted or error-free
operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE
LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON
SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR
OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE
OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND
EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND
AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG
AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN
THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some provinces or territories may or may not allow limitations on
how long an implied warranty lasts, or the exclusion or limitation
of incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which
vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
1-800-SAMSUNG (726-7864) or
www.samsung.com/ca/support (English),
www.samsung.com/ca_fr/support (French)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement