advertisement
▼
Scroll to page 2
24" (61 CM), 27" (68.6 CM), AND 30" (76.2 CM) INDOOR/OUTDOOR ELECTRIC WARMING DRAWER PRODUCT MODEL NUMBERS KOWT100E PRODUCT DIMENSIONS KOWT104E KOWT107E B ELECTRICAL CONNECTION A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this warming drawer be provided. A LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. • Cutout dimensions that are shown must be used. Given dimensions provide minimum clearance with warming drawer. • Recessed installation area must provide complete enclosure around the recessed portion of the warming drawer. • Grounded electrical supply is required. See “Electrical Requirements” section. • Electrical supply outlet should be located in the rear wall on the upper right-hand side of the cutout or in an adjacent cabinet. The outlet must be recessed. If the electrical outlet is located in an adjacent cabinet, a 1³⁄8" (3.5 cm) minimum diameter hole should have been drilled in the back of the cutout or support surface to pass the power supply cord through to the outlet. • Warming drawer support surface must be solid, level and flush with bottom of cabinet cutout. • Warming drawers with oiled bronze, black glass, and white glass panels are approved for indoor use only. For best performance results make sure the warming drawer is leveled before completing installation. There is no way to level the warming drawer after it has been installed. If the installation is not level, the door may slide open or not seal tightly, allowing heat to escape. C E D WARMING DRAWER SIZE OVEN DEPTH (A) RECESSED WIDTH (B) RECESSED HEIGHT (C) OVERALL WIDTH (D) DRAWER FRONT HEIGHT (E) 24" (61 cm) 23¹⁄8" (58.7 cm) 22¹⁄4" (56.5 cm) 9" (22.9 cm) 23³⁄4" (60.3 cm) 10¹⁄4" (26.1 cm) 27" (68.6 cm) 23¹⁄8" (58.7 cm) 25¹⁄4" (64.1 cm) 9" (22.9 cm) 26³⁄4" (67.9 cm) 10¹⁄4" (26.1 cm) 30" (76.2 cm) 23¹⁄8" (58.7 cm) 28¹⁄4" (71.8 cm) 9" (22.9 cm) 29³⁄4" (75.6 cm) 10¹⁄4" (26.1 cm) CABINET OPENING DIMENSIONS Cabinet Front View Front view 120 volt grounded outlet (or located in adjacent cabinet) A B Warming drawer cutouts A B Toe kick WARMING DRAWER SIZE MINIMUM BETWEEN CUTOUTS (A) CUTOUT HEIGHT (B) MINIMUM/ RECOMMENDED (C) CUTOUT WIDTH (D) MINIMUM CABINET WIDTH (E) 24" (61 cm) 2¹⁄2" (6.4 cm) 9¹⁄8" (23.2 cm) 1" (2.5 cm)/ 4¹⁄4" (10.8 cm) 22¹⁄2" (57.1 cm) 24" (61 cm) 27" (68.6 cm) 2¹⁄2" (6.4 cm) 9¹⁄8" (23.2 cm) 1" (2.5 cm)/ 4¹⁄4" (10.8 cm) 25¹⁄2" (64.8 cm) 27" (68.6 cm) 30" (76.2 cm) 2¹⁄2" (6.4 cm) 9¹⁄8" (23.2 cm) 1" (2.5 cm)/ 4¹⁄4" (10.8 cm) 28¹⁄2" (72.4 cm) 30" (76.2 cm) Warming drawer can be installed as an indoor single or double installation or installed under a single oven. Two warming drawers under a single oven are shown. NOTE: The warming drawer cannot be leveled after being installed. For outdoor installation follow the cutout dimensions above. Install the outdoor warming drawer in a permanent fixture. Custom Wood Drawer Front If you plan to install a custom wood panel to match your cabinets, we recommend consulting a qualified cabinetmaker or carpenter. The back of the wood panel must be sealed to avoid moisture damage. C D E Page 1 of 2 Because Whirlpool Corporation includes a continues commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications Ref. W10713339A subject to change without notice. 03/15 Clearance Dimensions – Flush Installation Flush Installation Requirements A 25³⁄8" (64.5 cm) minimum cutout depth is required. These dimensions will result in a ¹⁄4" (6 mm) reveal on all sides of the warming drawer. The front face of the cleats and platforms will be visible and should be treated as a finished surface. Side View Front View Cabinet Back F Top View A 1" (25 mm) Side Cleats* ⁷⁄₈” (22 mm) Platform* E F B e Side Cleat* C 1⁵⁄₈" (4.1 cm) D 27" Models 30" Models A Width of flush inset cutout (minimum) 27¹⁄4" (69.2 cm) 30¹⁄4" (76.8 cm) B Height between cutouts (minimum) 2¹⁄2" (6.4 cm) 2¹⁄2" (6.4 cm) C D Height of flush inset cutout (minimum) 10³⁄4" (27.3 cm) 10³⁄4" (27.3 cm) Bottom of cutout to floor (recommended) 8¹⁄4" (21.0 cm) 8¹⁄4" (21.0 cm) Bottom of cutout to floor (minimum) 5" (12.7 cm) 5" (12.7 cm) E Width of opening (minimum) 25¹⁄4" (64.1 cm) 28¹⁄4" (71.8 cm) F Depth of cutout (minimum) 25³⁄8" (64.5 cm) 25³⁄8" (64.5 cm) e Recommended outlet location Page 2 of 2 Because Whirlpool Corporation includes a continues commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications Ref. W10713339A subject to change without notice. 03/15
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project