GE GTD84GCSNWS 7.4-cu ft Steam Cycle Gas Dryer ENERGY STAR Installation instructions


Add to my manuals
4 Pages

advertisement

GE GTD84GCSNWS 7.4-cu ft Steam Cycle Gas Dryer ENERGY STAR Installation instructions | Manualzz

GTD84GCSN/GCPN

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

EXHAUST OPTION: When viewed from the front of the unit, exhaust 3-way via rear, left and bottom.

Dryer is shipped exhausted to the rear. Alternate exhausting knockouts are supplied.

GAS: An individual, properly-grounded branch circuit, with a three-prong grounding-type receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.

GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6A

GAS (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check installation instructions for correct kit and have a qualified gas technician install a conversion kit. See dryer ducting information for proper installation.

NOTE: Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position.

INSTALLATION INFORMATION: For complete information, see installation instructions packed with your dryer.

SPECIAL INSTALLATION REQUIREMENTS

ALCOVE OR CLOSET INSTALLATION:

- If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

- The dryer MUST be exhausted to the outside.

- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side; 1" front, top and rear

- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

BATHROOM OR BEDROOM INSTALLATION:

- The dryer MUST be exhausted to the outdoors.

- The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI

Z223 for gas dryers.

MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET

INSTALLATION:

- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear

DRYER EXHAUSTING INFORMATION :

- Use metal duct only, vertical and horizontal ducting.

For answers to your Monogram, GE Café ™ Series, GE Profile ™ Series or

GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.

Specification Created 7/19

GTD84GCSN/GCPN

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

5

22 1/2" 30 1/2"

27"

2

30-1/2

27"

Power Cord 4 1/2"

Back View

Power

Cord Hole

Back View

4-1/2

48"

40 1/2"

8"

3 1/2"

1 3/4"

5 1/4"

2" Riser

Side View

7"

Rear View

2" Riser

For answers to your Monogram, GE Café ™ Series, GE Profile ™ Series or

GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.

Specification Created 7/19

GE Dryer Vent

GTD84GCSN/GCPN GE Dryer Vent

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED

WITH YOUR DRYER.

DUCTING MATERIALS:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

EXHAUST LENGTH CALCULATION:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,

PLEASE CALL 1-800-GE-CARES.

DRYER EXHAUSTING INFORMATION—

USE METAL DUCT ONLY VERTICAL AND

HORIZONTAL DUCTING

BEST PERFORMANCE

A

A

4

B

Maximum length of 4" dia rigid metal duct

4

Domestic dryer models

2-1/2

Number of 90° turns

Exhaust hood type

A

4" opening

B

2-1/2" opening

Long Vent 6.1-7.4 cu. ft.

2-1/2

2

3

0

1

4

5

120 ft.

100 ft.

85 ft.

70 ft.

60 ft.

55 ft.

90 ft.

75 ft.

65 ft.

55 ft.

45 ft.

35 ft.

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct.

Specification Created 7/19

GTD84GCSN/GCPN

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

FEATURES AND BENEFITS

Steam – Dewrinkle and refresh your laundry right in the dryer thanks to innovative built-in steam technology.

Built-in WiFi – Enjoy the ultimate in convenience and the latest in technology with the ability to monitor and control your laundry from anywhere and receive real-time notifications and updates.

HE Sensor Dry – Prevent over-drying and get more wear out of your clothing thanks to innovative dual thermistor technology, that continually monitors temperature and moisture in the dryer.

Up to 120 ft. venting – Maximize your dryer’s performance with innovative venting, designed to provide optimal airflow, enhanced drying ability, and flexible installation.

Wrinkle Care – Spend less time ironing thanks to an innovative wrinkle care system that allows you to tumble clothes without heat to reduce creasing.

Digital Touch Controls – Quickly and easily adjust your settings to do laundry your way using these sleek controls.

My Cycle Settings – Streamline your laundry by choosing your favorite dryer settings on any cycle and saving them for future use.

Quick Dry – Dry a full load in less time thanks to innovative quick dry technology.

Damp Alert – Be notified when clothes are the ideal dampness to remove from the dryer for wrinkle-free results.

Dry Level Options – Four different drying levels to dry the way you want.

Temperature Options – Four different temperatures for full control over the drying process.

Sanitize Cycle – Reduce certain types of bacteria by 99.8% with this cycle.

Model GTD84GCSNWS – White with silver backsplash

Model GTD84GCPNDG – Diamond Gray

SMART

MIXED LOAD

DELICATES

JEANS

ACTIVE WEAR

STEAM CYCLES

Refresh Dewrinkle

Small Loads Large Loads

BULKY

Comforter

SANITIZE

TIMED DRY

Cycle Status:

Sensing

Drying

Cooling

Pause

Damp

Controls

90 min.

60 min.

40 min.

On

Warm

Up

10 min.

Time

More Dry

Dry

Less Dry

Damp

Level

Est. Time

Remaining

High

Medium

Low

No Heat

*

Temp

Check Vent

Less

Time

More

Time

Select

My Cycle Delay

Dry

Control

Lock* eco

Dry

Wrinkle

Care

Sound

GTD84

Specification Created 7/19

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement