GE GTX42EASJWW 6.2-cu ft Electric Dryer Dimensions Guide

GE GTX42EASJWW 6.2-cu ft Electric Dryer Dimensions Guide
GTX42EASJ
GE Appliances 6.2 Cu. Ft. Capacity Aluminized
Alloy Drum Electric Dryer with HE Sensor Dry
22 1/2"
26 3/4"
27"
POWER CORD 4 1/2"
11 3/4"
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRIC DRYER RATING:
240V
5600W
24A
60Hz
208V
4400W 22A
60Hz
44"
37 1/2"
EXHAUST OPTION: 4-way rear, right,
left and bottom
CIRCUIT REQUIREMENTS: An
individual, properly-grounded branch
circuit, protected by a 30-amp circuit
breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be
located within 36" of service cord entry
and acessible when dryer is mounted in
position.
INSTALLATION INFORMATION:
For complete information, see installation
instructions packed with your dryer.
4 1/4"
1 3/4"
4"
SIDE VIEW
5"
3 1/4"
REAR VIEW
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- I f your dryer is approved for installation in an alcove or closet, it will be stated on a label on
the dryer back.
-T
he dryer MUST be exhausted to the outside.
-M
inimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 1" front, top and rear
-C
loset doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed. If this closet contains both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of open area equally distributed.
- No
other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
-T
he dryer MUST be exhausted to the outdoors.
-T
he installation must conform with the local codes, or in the absence of local codes, with the
National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
-M
inimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION­:
Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Listed by
Underwriters
Laboratories
Specification Revised 7/16
GE Dryer Vent
GTX42EASJ
GE Dryer Vent
GE Appliances 6.2 Cu. Ft. Capacity Aluminized
Alloy Drum Electric Dryer with HE Sensor Dry
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED
WITH YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust
duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting
can be used (Kit WX08X10077). In special installations, it may be necessary to connect the
dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal
(foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semirigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the
entire length of the transition duct. Please see installation instruction packed with your
dryer for complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1.Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct
length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
Maximum length
of 4" dia rigid
A 4
metal duct
B
Exhaust hood type
A
Number
A
B
of 90°
4"
2-1/2"
4
2-1/2
Domestic dryer
turns
opening opening
B models
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2-1/2
Long Vent 6.1-7.4 cu. ft.
2
85 ft.
65 ft.
capacity electric & gas
3
70 ft.
55 ft.
(GTD33, GTD42, GTD45,
4
60 ft.
45 ft.
GTD65, GTX22, GTX33, GTX42
and GTX65)
5
55 ft.
35 ft.
A
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire
hazard or moisture could cause damage. Never terminate the exhaust into a common duct or
plenum with a kitchen exhaust, since the combination of lint and grease could create a fire
hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE
CALL 1-800-GE-CARES.
Listed by
Underwriters
Laboratories
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 7/16
GTX42EASJ
GE Appliances 6.2 Cu. Ft. Capacity Aluminized
Alloy Drum Electric Dryer with HE Sensor Dry
FEATURES AND BENEFITS
Auto Dry – For clothes that come out feeling and looking great, this setting
monitors air temperature to set the optimal drying time
Wrinkle Care extended tumble – Reduces wrinkling and creasing
End-of-cycle signal – Alerts you when the load is done, so clothes can be
removed before wrinkles set in
4 heat selections – Provide the right temperatures for your clothes-drying needs
Flat Back Design – Makes it easy to install in small areas like closets and utility
rooms where space is limited
Up to 120 ft. venting capability – Provides flexible installation
Model GTX42EASJWW – White
GTX42EASJWW_GTX42GASJWW_GTD42EASJ_GTD42GASJ
Specification Revised 7/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement