Celiera KHP-15 User guide

Celiera KHP-15 User guide
• KHP PTAC Units
PACKAGED TERMINAL
AIR CONDITIONER/HEAT PUMP
Before using your air conditioner, please read
this manual carefully and keep it for future reference.
CONTENTS
1. SAFETY PRECAUTIONS..................................................................2
2. IMPORTANT SAFETY INSTRUCTIONS ..........................................4
3. AIR CONDITIONER FEATURES.......................................................5
4. CONTROL PANEL OPERATION.......................................................6
5. DIP SWITCHES CONFIGURATION...................................................8
6. INSTALLATION..................................................................................11
7. CARE AND CLEANING.....................................................................13
8. TROUBLESHOOTING.......................................................................14
Read This Manual
Inside you will find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time
and money over the life of your air conditioner. You'll find many answers to common
problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting
Tips first, you may not need to call for service at all.
! CAUTION
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
the appliance. Cleaning and user maintenance shall not be made by children without
supervision. ( be applicable for the European Countries )
This appliance is not intended for use by persons (including children) with reduced
physical ,sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. (be applicable for other countries except the
European Countries )
Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
The appliance shall be installed in accordance with national wiring regulations.
Do not operate your air conditioner in a wet room such as a bathroom or laundry room.
The appliance with electric heater shall have atl east1 meters pacet ot hec ombustible
materials.
Contactthe authorised service technician for repair or maintenance of this unit.
Contact the authorised installer for installation of this unit.
1
SAFETY PRECAUTIONS
To prevent injury to the user or other people and property damage, the following instructions
must be followed. Incorrect operation due to ignoring of instructions may cause harm or
damage. The seriousness is classified by the following indications.
!
WARNING
This symbol indicates the possibility of death or serious injury.
!
CAUTION
This symbol indicates the possibility of injury or damage to property.
Meanings of symbols used in this manual are as shown below.
Never do this.
!
Always do this.
! WARNING
!
!
!
!
!
!
Plug in power plug
properly.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
Do not damage or use an
unspecified power cord.
Otherwise, it may cause electric
shock or fire due to excess heat
generation.
It may cause electric shock or fire
due to heat generation.
It may cause electric shock or fire.
If the power cord is damaged, it
must be replaced by the manufacturer or an authorised service
centre or a similarly qualified person in order to avoid a hazard.
Do not modify power cord
length or share the outlet
with other appliances.
Do not operate with wet
hands or in damp
environment.
It may cause electric shock or
fire due to heat generation.
It may cause electric shock.
This could damage your health.
Always ensure effective
earthing.
Do not allow water to run
into electric parts.
!
Incorrect earthing may cause
electric shock.
It may cause failure of machine
or electric shock.
Incorrect installation may cause
fire and electric shock.
Unplug the unit if strange
sounds, smell, or smoke
comes from it.
Do not use the socket if it is
loose or damaged.
It may cause fire and electric
shock.
It may cause fire and electric
shock.
Keep firearms away.
Do not use the power cord
close to heating appliances.
It may cause fire.
It may cause fire and electric
shock.
Ventilate room before operating air
conditioner if there is a gas leakage from
another appliance.
Do not direct airflow at
room occupants only.
Always install circuit
breaker and a dedicated
power circuit.
Do not open the unit
during operation.
It may cause electric shock.
Do not use the power cord near
flammable gas or combustibles, such
as gasoline, benzene, thinner, etc.
It may cause an explosion or fire.
Do not disassemble or modify unit.
It may cause failure and electric shock.
It may cause explosion, fire and, burns.
2
! CAUTION
Do not clean the air
conditioner with water.
When the air filter is to be
removed, do not touch the
metal parts of the unit.
It may cause an injury.
!
When the unit is to be
cleaned, switch off, and turn
off the circuit breaker.
Do not clean unit when
power is on as it may cause
fire and electric shock, it may
cause an injury.
!
Stop operation and close
the window in storm or
hurricane.
Operation with windows
opened may cause wetting
of indoor and soaking of
household furniture.
Do not place obstacles
around air-inlets or inside
of air-outlet.
It may cause failure of
appliance or accident.
Do not use strong detergent such as wax or
thinner but use a soft cloth.
Appearance may be
deteriorated due to change
of product color or
scratching of its surface.
!
Ventilate the room well when
used together with a stove,
etc.
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
An oxygen shortage may occur.
This could injure the pet or
plant.
Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects.
It may cause deterioration of
quality, etc.
! Turn off the main power
switch when not using the
unit for a long time.
Hold the plug by the head
of the power plug when
taking it out.
!
Do not use for special
purposes.
It may cause electric shock
and damage.
!
Ensure that the installation bracket of
the outdoor appliance is not damaged
due to prolonged exposure.
If bracket is damaged, there
is concern of damage due to
falling of unit.
Do not place heavy object on the
power cord and ensure that the cord
is not compressed.
There is danger of fire or
electric shock.
!
Use caution when unpacking and
installing. Sharp edges could cause injury.
!
Clean the evaporator once every three
months by professional people.
!
Otherwise it may cause failure of electric
heating feature.
3
It may cause failure of product
or fire.
!
Always insert the filters
securely. Clean filter once
every two weeks.
Operation without filters may
cause failure.
Do not drink water drained
from air conditioner.
It contains contaminants and
could make you sick.
If water enters the unit, turn the unit off at the power
outlet and switch off the circuit breaker. Isolate
supply by taking the power-plug out and contact a
qualified service technician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
NOTE The power supply cord with
this air conditioner contains a current
detection device designed to reduce
the risk of fire.
Please refer to the section Operation
,
of Current Device for details.
In the event that the power supply
cord is damaged, it cannot be
repaired-it must be replaced with a
cord from the Product Manufacturer.
,
Do not, under any
circumstances, cut,
remove, or bypass
the grounding prong.
Power supply cord
with 3-prong grounding plug
and current detection device
For your safety
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
Avoid fire hazard or electric shock. Do not use an extension cord or an
adaptor plug. Do not remove any prong from the power cord.
WARNING
Electrical Information
Be sure the electrical service is adequate for the model you have
chosen. This information can be found on the serial plate, which
is located on the side of the cabinet and behind the grille.
Be sure the air conditioner is properly grounded. To minimize
shock and fire hazards, proper grounding is important. The power
cord is equipped with a three-prong grounding plug for protection
against shock hazards.
Your air conditioner must be used in a properly grounded wall
receptacle. If the wall receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or circuit breaker,
have a qualified electrician install the proper receptacle.
Ensure the receptacle is accessible after the unit installation.
Do not run air conditioner without side protective cover in place.
This could result in mechanical damage within the air conditioner.
The appliance shall be installed in accordance with national wiring
regulations.
Do not use an extension cord or an adapter plug.
NOTE:
The shape may be different according to its model:
Power Card
Power Suppy
230V,15A
230V,20A
230V,30A
4
265V,15A
265V,20A
265V,30A
Operation of Current Device(optional)
The power supply cord contains a current device that senses damage to the power cord. To test your power
supply cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug head.
Press the TEST button, you will notice a click as the RESET
button pops out.
3. Press the RESET button, again you will notice a click as the button
engages.
4. The power supply cord is now supplying electricity to the unit.
(On some products this it also indicated by a light on the plug head.)
NOTES:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply must be replaced if it fails reset when either the TEST button is pushed, or it cannot be
reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from the
product manufacturer.
When 265V units are to be installed,the power supply must be permanent wiring.Permanent
wiring may be done through the accessory subbase.An exposed cord connection on 265V units
are not permitted.
AIR CONDITIONER FEATURES
This unit has many featrues.The servicer must be
familiar with these features in order to properly
service the unit.
Automatic Quick Warm-up (for heat pump
models only)
If the room temperature falls to 4.5 OC/8 OF
below the set point temperature,the reverse
cycle heat is shut off and the electric strip heat
is turned on for one cycle,until heating is
satisfied.
LED Indicators and Buttons
The touch pad has buttons for MODE,FAN,
POWER,SETPOINT UP and SETPOINT DOWN.
It also has LEDs that correspond to the mode,
fan speed,power and setpoint operation,to
indicate the unit s status.LEDs for HIGH,MED
,
and LOW indicate the fan speed that is selected.
LEDs for FAN,COOL and HEAT indicate what
operating mode is active.LED for POWER is the
unit ON/OFF status LED.If the unit is in ON mode,
the LED will be green.If the unit is OFF,the LED
will be off.
Compressor Restart Delay
This feature extends the overall life of compressor by preventing the short-cycling of the air
conditioner.When the compressor restarts,the
unit is designed to give a minimum of three
minutes to have a time of equalizing the refrigerant pressures for optimizing cycling.
Memory
The unit has memory .If power is lost,all of the
control settings(mode,fan speed,on/off and
configuration) are remembered.So when power
is restored,the unit will start back up in the mode
(and configuration) it was in,when power was
lost.
NOTE: HEAT mode is for Cooling & Heating models only.
High Temperature Protection In Heating
Operation
The compressor and(or) electric heater will be
switched off to prevent damage in high indoor
blow air temperature or error indoor temperature
sensor.
Unit Configuration
O
F or OC
The unit can display in either OF or OC.
Automatic Evaporator Freeze Protection
Automatically to keep the evaporator from
freezing,the compressor is tuuned off and the
indoor fan is turned on when the evaporator
temperature is too lower.If the evaporator
temperature is not too lower this function is off.
5
CONTROL PANEL OPERATION
The control panel keypad will look like the following
Fig.1. For some models with REMOTE SIGNAL
RECEPTOR, the unit can be controlled by the control
panel alone or by the remote. NOTE: Some models
have no REMOTE SIGNAL RECEPTOR.
REMOTE SIGNAL
RECEPTOR
Fig.1
POWER
- Press the POWER button to turn the unit on or off.
When the unit is on,the power indicator light will be
green.When the unit is off,the light will go out.
MODE
- Push this button to cycle through the modes from
COOL-HEAT-FAN-COOL.The indicator light beside
the "MODE" option will illuminate, identifying the
mode selected.
- COOL:The range of set temperature is 17OC/62OF
~30 OC/86O F.Cooling begins automatically when the
room temperature is above the set point,and stops
when the room temperature is 2OC(4OF) below the
set point.But the compressor will run 5 minutes at
least in COOL mode before stoping. The fan runs
in continuous mode.
- HEAT:The range of set temperature is 17OC/62OF
~29OC/84OF.For heat pump models,the unit can
alternate to run between in reverse cycle heat mode
and electric heater mode according to the difference
between the setting temperature and the room
temperature.The fan motor cycles on and off
with the compressor and electric heater.
NOTE:
The reverse cycle and electric heater cannot be run at
the same time. In following cases, it is normal that the
reverse cycle does not operate.
1.When the outdoor temperatrue is lower than 4O C/40 O F
or the room temperature falls to 4.5O C/8 O F below the
set point temperature.
2.There is a 3-minute minimum compressor run time at
any setting to prevent short cycling. The indoor fan
motors starts before the compressor and stops after
the compressor cycles off.
3.Push the S1 on the DIP SWITCHES to UP (ON)
position.
4.When frost builds up to the evaporator coils,the unit
will defrost automatically and the compressor will cycle
off.
- FAN:Fan operation only without heating and cooling.
6
Note: If the unit has DIP SWITCHES feature,the
temperature range can be setted is controlled by
DIP SWITCHES.See DIP SWITCHES CONFIGURATIONS on page 8 for details.
UP/DOWN BUTTONS (
/
)
- Push the UP (or DOWN) button to increase (or
decrease) the set temperature of the unit in cooling
or heating mode.The temperature can be set by
O
O
increments of 1C
(1F).The
setting temperature
appears in the display.
NOTE:Press and hold
and
buttons together
for 3 seconds will alternate the temperature display
between OC & OF scale.
FAN (FAN SPEED)
- Every time you push this button,the fan speed
cycles through the settings as follows:HIGH-MEDLOW-HIGH.
DISPLAYS:
- Shows the set temperature inOC or O F. While on
Fan only mode,it shows the room temperature.
Control code (on some models):
LC-Pads on the control panel is not available.The
unit can be setted by using wire cotroller only.
FC-Pads on the control panel and wire controller
are not available. The unit can be setted by
using FRONT DESK CONTROL only.
Error codes:
AS-Room temperature sensor error;
ES-Evaporator temperature sensor error;
CS-Condenser temperature sensor error;
OS-Outside temperature sensor error;
HS-Exhaust temperature sensor error;
LE-Wire cotroller error;
NOTE:When error occurs,unplug the unit and plug
it back in.If error repeats, call for service.
Other codes:
LO-Room temperature is lower than 0OC/32OF;
HI-Room temperature is higher than 37OC/99OF;
FP-Low temp. Protection.
NOTE: All the illustrations in this manual are
for explanation purpose only. Your air
conditioner may be slightly different.
The actual shape shall prevail.
NOTE:This air conditioner is designed to be
operated under condition as follows:
Cooling Outdoor temp:
operation
Indoor temp:
Heating Outdoor temp:
operation Indoor temp:
18-43OC/64-109OF (18-52OC/64-125OF
for special tropical models)
17-32 C/62-90FO
-5-24 C/23-76F O
0-27 C/32-80FO
O
O
O
Note: Performance may be reduced outside of
these operating temperatures.
CONTROL PANEL OPERATION(CONTINUED)
Accessory
THIS UNIT IS CONTROLLED BY WALL MOUNTED THERMOSTAT
NOTE:When the unit displays LC (Pads on the
control panel is not available.The unit can be setted
by using wire cotroller only.) You can install the
Accessory on the control panel.
NOTE: For some models, there is corresponding
operation happened after 3 seconds when pressing
any button.
NOTE: When the are wide differences between
USERS MANUAL and Remote controller Illustration
on function description, the description on USERS
MANUL shall prevail.
7
DIP SWITCHES CONFIGURATIONS (Optional)
2
REMOVING THE FRONT PANEL
- Dip switches controls are located behind front panel,
through an opening below the control panel.To
access,remove front panel.See Fig.2.
- Dip switches are accessible without opening the
control box.See Fig.3.
- Unit must be powered OFF to effectively change
their status.
A4 A5
X
A0A3
UP(ON)
DOWN(OFF)
1 2 3 4
S9
1 2
S1
S2
S3
S4
S5
S6
1 2 3 4
S7
1 2 3 4
S8
1
- Pull out at the bottom to release it from the tabs
- Then lift up 2 .
DIP SWITCHES CONFIGURATIONS
Fig.2
- See Table 1 and Fig.4 for Dip Switches configurations
and functions of each dip switch position.
1
.
Dip Switches
Wall thermostat type
Heating type
Temperature display type
Control type
Setpoint limit 1
Setpoint limit 2
Fan CON/CYC for heating
Fan CON/CYC for cooling
Fig.3
Fig.4
Table 1
No .
S1
DIP SWITCHES CONFIGURATIONS
UP(ON)
DOWN(OFF)
Electric Heat Only
Remarks
Electric Heat and Pump Heat
O
S2
Temperature Display in C
S3
Wall Thermostat Enable
Temperature Display in F
Control Panel Enable
UP*UP:61OF~86 O F(16OC~30 O C);
S4*S5 UP*DOWN:65OF~78 O F(18OC~26 O C);
Two configurations (S4*S5)
combine to select set point
range.
DOWN*UP:63OF~80 O F(17OC~27 O C);
S6
For Heat Pump unit only
O
DOWN*DOWN:68OF~75 O F(20OC~24 OC);
Fan Continuous Run for Heating Fan Cycle for Heating
S7
Fan Continuous Run for Cooling
S9
Use some types of wall
Thermostat
Fan Cycle for Cooling
Use PTAC other Wall
Thermostat
NOTE: On heating mode, the setting temperature
O
O
can not be higher than 29C/84F.
Electric Heat Only (for heat pump unit only)
- This setting is typically used for Emergency Heating.
Wall Thermostat Enable
- A wired wall thermostat can be connected to the
unit .If it is,this dip switch must be moved to the
Wall Thermostat Enable Position,before the wall
thermostat will begin control.
Setpoint Temperature Limits
- Provides a restricted range of temperature control.
8
you can consult with the
sales agency or manufacturer
for details
Heat and Cool Fan CON/CYC Dip-switches
- Allows the fan to operate in continuous or cycle
modes while the unit is in heating and cooling mode.
CON(Continuous)
- Allows fan to run continuously,circulating air even when the
temperature setting has been satisfied.This switch helps to
maintain the room temperature closer to the thermostat
setting.
CYC(Cycle)
- This setting allows the fan to cycle on and off with the
compressor or electric heater.The fan stops a short time
after the temperature setting is satisfied.
WALL THERMOSTAT TERMINAL (Optional)
IMPORTANT: Only trained, qualified personnel
should access electrical panel on unit and install
electrical accessories. Please contact your local
electrical contractor, dealer, or distributor for
assistance.
Thermostat Wire Routing
Thermostat wire is field supplied. Recommended
wire gauge is 18 to 20 gauge solid thermostat wire.
NOTE: It is recommended that extra wires are run
to unit in case any are damaged during installation.
Thermostat wire should always be routed around
or under, NEVER through, the wall sleeve. The
wire should then be routed behind the front panel
to the easily accessible terminal connector.
- Insert the wire connector of the wall thermostat into
the relevant terminal according to different shapes as
shown below.
Terminal of some types of wall
thermostat
Dip switch
Installation instruction of PTAC other Wall
Thermostat
- Remove the two screws as shown below and take the cover
panel down.
Remove the two screws
Take the cover panel down
Terminal of PTAC other Wall
Thermostat
NOTE: Refer to thermostat installation instructions
for details on installing wall thermostat.
Installation instruction of some types of wall
Thermostat (you can Consult with the
sales agency or manufacturer for details)
- Pull the dip switch to the DOWN(OFF) position as
shown below.
Dip switch
9
TERMINAL
24V(L)
24V(N)
COMP
HEAT1
HEAT2
4-WAY
HI-FAN
Fig. A - Proper Wire Routing Beneath Unit
LOW-FAN
FC(L)
THERMOSTAT WIRE ROUTING
(UNDER SLEEVE, BEHIND FRONT PANEL)
FC(N)
Terminal of PTAC other Wall Thermostat
DESIGNATION
FC(L)
Front desk control terminal L
FC(N)
Front desk control terminal N
LOW-FAN
Low fan speed
HI-FAN
High fan speed
4-WAY
4-way valve(For heat pump system)
HEAT2
Electrical heater 2
HEAT1
Electrical heater 1
COMP
Compressor
24V(N)
24VAC terminal N
24V(L)
24VAC terminal L
WALL THERMOSTAT TERMINAL (Optional)
FRONT DESK CONTROL
! CAUTION
The controller can handle a switch signal from FC(L) and
FC(N) input, called front desk control. Input must be 24VAC.
If system doesn't receive a 24VAC signal, it will turn unit
off; otherwise, the unit runs in normal control.
UNIT DAMAGE HAZARD
Failure to follow this caution may result in
equipment damage or improper operation.
Improper wiring may damage unit electronics.
Common busing is not permitted. Damage or
erratic operation may result.
NOTE:
Use terminal 4-way for heat pump connection
only.
Suggest set the compressor protection time
morn than 3 minutes in wall thermostat. If set less
than 3 minutes, the compressor will restart delay
3 minutes still.
Wall thermostat must be heating changeover 4-way
valve.
For thermostats that have only one fan speed
output (on or auto),the fan speed is determined
by how the terminal connector is wired. If Low
fan is desired, wire the G output from the
thermostat to (LOW-FAN) on the units terminal
block. If High fan is desired, wire the G output
from the themostat to (HI-FAN) on the units
terminal block.
The range of set tempreture of Wall thermostat
must be in consonance with the range of DIP
switch setting.
Wall thermostat must be set the type properly
in consonance with the unit type : heat pump
or no heat pump.
If the Wall thermostat has only one electrical
heater output, connect the two terminals of HEAT 1
and HEAT 2, the unit can operate two electrical
heaters(only for the unit has two electrical
heaters). Otherwise operate one electrical heater.
Please do not remove the control panel.
10
- The DIP switch can control the FRONT DESK CONTROL
feature. The DIP switch is on the DOWN position, the unit will
be turn off; otherwise,the unit runs in normal control.
See FigB.
Dip switch of FRONT
DESK CONTROL
FigB.
INSTALLATION
HOW TO INSTALL THE UNIT
Dimension of air conditioner
! CAUTION
1067mm/42inch
There are sharp edges that can cause serious cuts.
When lifting the air conditioner,it is HEAVY.Use 2
people to lift.
408mm/16inch
- For existing sleeve,you should measure the wall
sleeve dimensions.
- Install the new air conditioner according to these
installation instructions to achieve the best performance.
All wall sleeves used to mount the new air conditioner
must be in good structural condition and have a rear
grille that securely attaches to the sleeve or the flange
of the sleeve to secure the new air conditioner.
- To avoid vibration and noise,make sure the unit is
installed securely and firmly.
- When installing the sleeve,make certain there is
nothing within 20 of the back that would interfere
with heat radiation and exhaust air flow. (See Fig.2)
606mm/23.9inch
Dimension of sleeve assembly (optional)
1067mm/42inch
408mm/16inch
376mm/14.8inch
COOLED
AIR
WALL
SLEEVE
HEAT
RADIATION
Shipping
tape
Over 20
INTAKE
AIR
WALL
Fig.3
2
Fig.2
PREPARATION OF SLEEVE ASSEMBLY(optional)
- Refer to the installation instruction of sleeve assembly
for details.
PREPARATION OF REAR GRILLE ASSEMBLY(optional)
- Refer to the installation instruction of rear grille
assembly for details.
UNIT INSTALLATION
- Carefully remove shipping tapes from the front panel.
(See Fig.3)
1
- Pull out at the bottom to release it from the tabs
- Then lift up 2 .
Fig.4
Shipping
screw
- Remove the front panel. (See Fig.4)
- Remove the shipping screw from the vent door.(See
Fig.5)
11
Fig.5
1
.
INSTALLATION(CONTINUED)
UNIT INSTALLATION (CONTINUED)
- Rotate the vent control lever to either open or close
the vent door.(See Fig.6)
Vent control lever
Vent closed
Vent open
Fig.6
NOTE:When vent control lever set at CLOSE,only
the air inside the room is circulated and filtered.
When set at OPEN,some outdoor air will be drawn
into room.This will reduce heating or cooling
efficiency.
- Lift unit level and slide unit into wall sleeve until
firmly against front of wall sleeve and secure with
4 screws and washers (supplied in the SLEEVE
ASSEMBLY ) through the unit flange holes.
(See Fig.7 and Fig.8)
Fig.7
Fig.8
- Reinstall front panel.(See Fig.9)
1
2
Place tabs over top rail 1 . Push Inward at bottom
until panel snaps into place 2 .
Fig.9
12
! CAUTION
Do not put obstacles around air-inlet or
inside of air-outlet of the unit, such as window
curtain etc.
Always insert the filter securely, clean filter once
every two weeks as required.
CARE AND CLEANING
FRONT PANEL AND CASE
- Turn unit off and disconnect power supply.To clean,
use water and a mild detergent.DO NOT use bleach
and abrasivers.Some commercial cleaners may
damage the plastic parts.
OUTDOOR COIL
- Coil on outdoor side of unit should be checked
regularly.Unit will need to be removed to inspect
dirt build-up that will occur on the inside of the coil.
If clogged with dirt and soot ,coil should be
professionally cleaned.Clean inside and outside of
outdoor coils regularly.
NOTE: Never use a high-pressure spray on coil.
! CAUTION
- Removing Air Filter
2 Air filters
Pull up
Fig.9
- Replacing Air Filter
Push down
UNIT DAMAGE HAZARD
Failure to follow this caution may result in
equipment damge or improper operation.
Airflow restriction may cause damage to the unit.
Fig.10
AIR FILTERS
IMPORTANT:TURN UNIT OFF BEFORE
CLEANING.
VENT DOOR FILTER
IMPORTANT:TURN UNIT OFF BEFORE
CLEANING.
! CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in
equipment damge or improper operation.
Do not operate unit without filters in place.If a filter
becomes torn or damaged,it should be replaced
immediately.
Operating without filters in place or with damaged
filter will allow dirt and dust to reach indoor coil and
reduce cooling,heating,airflow and efficiency of unit.
Airflow restriction may cause damage to unit.
- The most important thing you can do to maintain
unit efficiency is to clean the filters once every
two weeks as required.
Clogged filters reduce cooling,heating and airflow.
- Keeping filters clean will:
Decrease cost of operation.
Save energy.
Prevent clogged indoor coil.
Reduce risk of premature component failure.
- To Clean Air Filters:
Vacuum off heavy soil.
Run water through filter.
Dry thoroughly before replacing.
- If the vent door is open,access requires the removal
of the unit from the wall sleeve.Clean the vent filter
twice a year or as required.
- Make sure to remove the shipping screw from the
vent door.(See.Fig.5)
- Rotate the vent control lever to open the vent door.
(See. Fig.6)
- Remove four screws from the vent door filter.
(See.Fig.11)
- First pull out the vent door steel wire from the hole
of the vent door, then take off the vent door and filter.
(See.Fig.11)
- Clean the filter.Dry thoroughly before replacing.
- Replac the vent door and filter,reinstall the four
screws.
- Reinsert the vent door steel wire into the hole of the
vent door.
Vent door
control lever
.
Screws
Vent door
steel wire
Vent door
filter
Fig.11
13
Vent door
TROUBLESHOOTING
POSSIBLE CAUSES
UNIT DOES NOT START
Unit may have become unplugged
Fuse may have blown
Circuit breaker may have been tripped
Unit may be off
Unit may be in a protection mode.
UNIT NOT COOLING/HEATING ROOM
Unit air discharge section is blocked
Temperature setting is not high or low
enough
Note:Setpoint limits may not allow the
unit to heat or cool the room to the
temperature desired.Check section on
dipswitch settings.
Unit air filters are dirty.
Room is excessively hot or cold when
unit is started.
Vent door left open.
Unit may be in a protection mode.
Compressor is in time delay.
DISPLAY HAS STRANGE NUMBERS/
CHARACTERS ON IT
UNIT MAKING NOISES
SOLUTONS
Check that plug is plugged securely in wall receptacle.
Note:Plug has a test/reset button on it.Make sure that the plug has
not tripped.
Replace the fuse.See Note 1.
Reset circuit breaker.See Note 1.
Turn unit on (bottom right button on keypad).
Make sure that curtains,blinds or furniture are not restricting or
blocking unit airflow.
Reset to a lower or higher temperature setting.
Remove and clean filters.
Allow sufficient amount of time for unit to heat or cool the room.Start
heating or cooling early before outdoor temperature,cooking heat or
gatherings of people make room uncomfortable.
Close vent door.
Check dipswitch and wall thermostat settings for desired comfort.
Wait approximately 3 minutes for compressor to start.
The unit may be in a protection mode.
O
The unit may be set for OC (instead of F).
Clicking,gurging and whooshing noises are normal during operation
of unit.
WATER DRIPPING OUTSIDE
If a drain kit has not been installed,condensation runoff during very
hot and humid weather is normal.See Note 2.If a drain kit has been
installed and is connected to a drain system,check gaskets and
fittings around drain for leaks and plugs.
WATER DRIPPING INSIDE
Wall sleeve is not installed level
Wall sleeve must be installed level for proper drainage of
condensation .Check that installation is level and make any
necessary adjustments.
ICE OR FROST FORMS ON INDOOR
COIL
Low outdoor temperature
Dirty filters
When outdoor temperature is approximately 55OF or below,frost
may form on the indoor coil when unit is in Cooling mode.Switch unit
to FAN operation until ice or frost melts.
Remove and clean filters.
COMPRESSOR PROTECTION
Power may have cycled,so compressor
is in a restart protection.
Random Compressor restart-Whenever the unit is plugged in,or
power has been restarted,a random compressor restart will occur.
After a power outage,the compressor will restart after approximately
3 minutes.
Compressor Protection-To prevent short cycling of the compressor,
there is a random startup delay of 3 minutes and a minimum
compressor run time of 3 minutes.
Clean the evaporator once every three months by professional
people.
ELECTRIC HEATING FAILURE
NOTES:
1.If circuit breaker is tripped or fuse is blown more than once,contact a qualified electrician.
2.If unit is installed where condensation drainage could drip in an undesirable location,an accessory drain kit
should be installed and connected to drain system.
14
Corporate Headquarters:
4051 Haggerty Rd West Bloomfield, MI 48323 USA
T: +1 866-777-7071 M-F 10a-6p ET
F: +1 248-363-7834
Service Center & Warranty Repairs Facility:
14850 Linwood St Detroit, MI 48238 USA
The design and specifications are subject to change without prior notice for product
improvement. Consult with the sales agency or manufacturer for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement