Remington REM-32-TTC-O 32000-BTU Portable Propane Tank Top Propane Heater User's Manual

PROPANE TANK TOP

HEATER

User’s Manual &

Operating Instructions

Model Numbers

REM-16-TTC-O / REM-32-TTC-O / REM-47-TTC-O

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR:

The temporary heating of adequately ventilated buildings or structures under construction, alteration or repair.

Factory ID: 522

DANGER

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH

THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS

OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, CARBON

MONOXIDE POISONING AND / OR ELECTRIC SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE

OR SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS

MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.

WARNING

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID

COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR

CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY

THESE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH DO OR MAY

CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,

SOLVENTS, PAINT THINNERS, DUST PARTICLES OR UNKNOWN CHEMICALS.

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (866) 676-1989

Fax: 320-251-2922 • Web: www.remingtonheater.com • Email: [email protected]

© 2017 Pinnacle Climate Technologies, Inc. RGTA-400

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE

CONNECTED TO A FUEL SOURCE

Table Of Contents

Safety Information.............................................1-3

Features and Specifications.............................4-5

Assembly.........................................................6-7

Operation........................................................8-10

Ventilation.............................................................9

Maintenance and Storage..................................10

Troubleshooting Guide.......................................11

Exploded View...................................................12

Parts List............................................................13

Warranty.............................................................14

WARNING NOT FOR HOME OR RECREATIONAL VEHICLE USE.

DANGER Carbon Monoxide Hazard This heater produces carbon monoxide, which has no odor. Burning the heater in an enclosed space can kill you. Never use the heater in enclosed spaces such as a tent, a camper, any vehicle or recreational vehicle (RV), enclosed shelter, or any other enclosed areas.

DANGER

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

DANGER

Not for use in residential living areas or in non-adequately ventilated enclosed spaces. Never bring or store a propane cylinder indoors.

WARNING

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR: The temporary heating of adequately ventilated buildings or structures under construction, alteration or repair.

WARNING

DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY

UNDERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS.

Failure to comply with the precautions and instructions provided with this heater can result in death, serious bodily injury, property loss or damage from the hazards of fire, explosions, burns, asphyxiation or carbon monoxide poisoning. Only persons who can read and understand these instructions should use or service this heater.

WARNING

This is an unvented portable heater. It uses air (oxygen) from the area in which it is used. Adequate combustion and ventilation air must be provided. Refer to

VENTILATION on Page 6.

WARNING

CALIFORNIA RESIDENTS: This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

This heater is designed and approved for use as a construction heater in accordance with Standard

ANSI Z83.7-2011/CSA 2.14-2011. CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU

HAVE ANY QUESTIONS ABOUT APPLICATIONS. Other standards govern the use of fuel gasses and heating products for specific uses. Your local authority can advise you about these.

© 2017, Pinnacle Climate Technologies, Inc. 1 Propane Tank Top Heater User’s Manual




WARNING

Safety Information

RISK OF INDOOR AIR

POLLUTION!

DANGER

PROPANE IS AN

EXPLOSIVE GAS!

WHAT TO DO IF THE SMELL OF GAS IS PRESENT:

The products described in this manual are propane direct-fired heaters. Direct-fired means that all of the combustion products of the heater enter the heated space. This appliance is rated at 98% combustion efficiency, but does produce small amounts of carbon monoxide.

DANGER

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

Carbon monoxide is toxic. Humans can tolerate only small amounts of carbon monoxide and so precautions should be taken to provide proper ventilation. Failure to provide proper ventilation in accordance with the instructions in this manual can result in death.

– DO NOT attempt to light the heater.

– Extinguish any open flame.

– Shut off gas to heater.

– If odor continues, contact your local gas supplier or fire department.

– DO NOT touch or use any electric switch or any electric device that can cause a spark.

– Immediately call your gas supplier from a neighbors phone. Follow the gas suppliers instructions.

– If you can not reach your gas supplier, call the fire department.

– Service must be done by a qualified service agency.

People with breathing problems should consult a physician before using this heater.

WARNING

RISK OF BURNS, FIRE AND

EXPLOSION!

Early signs of carbon monoxide poisoning resemble the flu. Symptoms of improper ventilation / carbon monoxide poisoning are:

Headache • Dizziness • Nausea • Dry Mouth

Sore Throat • Burning of Nose and Eyes

If you experience any of these symptoms:

GET FRESH AIR AT ONCE! Have your heater serviced and check for proper ventilation. Some people are more affected by carbon monoxide than others. These include: pregnant women, those with heart or lung problems, anemia or those under the influence of alcohol or at high altitudes.

FOR OUTDOOR USE. INDOOR USE

PERMITTED ONLY FOR: The temporary heating of adequately ventilated buildings or structures under construction, alteration or repair! Provide at least a three square foot

(2,800 sq cm) opening of outside air for every 100,000 Btu / Hr heater rating. Refer to

“Ventilation” on page 9 for further instructions.

NEVER store or use gasoline or other flammable vapors and liquids in the vicinity of this heater.

NEVER store a propane (LP) cylinder not connected to this heater in the vicinity of this heater.

NEVER connect heater to an unregulated gas supply.

NEVER obstruct the flow of combustion and ventilation air. (The front and rear of heater).

NEVER use duct work in front or rear of heater.

NEVER modify this heater or operate a heater that has been modified.

NEVER service, move or handle heater while still hot or operating

NEVER use heater in occupied dwellings.

NEVER use heater in a tent.





Safety Information

WARNING CAUTION! HOT WHILE IN

OPERATION. DO NOT TOUCH.

KEEP CHILDREN, ANIMALS, CLOTHING AND

COMBUSTIBLES AWAY FROM HEATER.

WARNING

The hose assembly shall be pro tected from traffic, building material and contact with hot surfaces both during use and while in storage.

Keep all combustible materials away from this heater.

Minimum Clearance From Combustibles

Sides

36 in.

Top

60 in.

Front

60 in.

Rear

36 in.

ALWAYS install the heater so that it is not directly exposed to water spray, rain, dripping water, or wind.

ALWAYS provide adequate clearance for accessibility, combustion and ventilation (air supply) while heater is operating.

WARNING

For use with propane (LP) gas only.

WARNING

DO NOT use any LP cylinder larger than 20 lbs.

– Use heater in accordance with all local codes.

In the absence of local codes, refer to The

National Fuel Code, ANSI Z223.1.

– This heater is shipped from the factory for use with propane (LP) gas only.

Do not convert to any other gas. Installation must conform to local codes, or in their absence, with the standard for the Storage and

Handling of Liquefied Petroleum Gases ANSI/

NFPA 58 and the Natural Gas and Propane

Installation Code CSA B149.1.

– Gas supply connections should be checked by using a 50/50 soap and water solution.

Never use a flame to check for gas leaks.

– Do not direct heater discharge towards the LP cylinder unless it is at least 20 feet from the heater.

– Use only the regulator and hose assembly provided with this heater. Inspect the regulator/hose assembly prior to each use of the heater. If there is excessive abrasion or wear, or if the hose is cut, replace it with the proper assembly shown in the parts list, prior to using the heater.

Min.

Max.

Minimum and Maximum Inlet Pressure

16-TTC 32-TTC

5 PSI

200 PSI

47-TTC

WARNING

RISK OF FIRE! ALWAYS ATTACH THE HEATER IN AN UPRIGHT VERTICAL

POSITION. ALWAYS LOCATE HEATER ON A STABLE AND LEVEL SURFACE!


Model #

BTU

Fuel Consumption (Lbs./hr)

Maximum Operating Hours

Required Cylinder Lbs.

Fuel Type

Heating Area (Ft.

2 )




Specifications

16-TTC

12 / 14 / 16,000

.56 / .65 / .74

35.9 / 30.8 / 27.0

32-TTC

25 / 28 / 32,000

1.16 / 1.30 / 1.49

17.2 / 15.4 / 13.4

20

Propane

20

Propane

300 / 350 / 400 620 / 700 / 800

Specifications subject to change without notice.

47-TTC

36 / 40 / 47,000

1.67 / 1.86 / 2.18

12.0 / 10.8 / 9.2

20

Propane

900 / 1000 / 1175

Features

16-TTC

Rear Guard

Ignition Hole

Front Guard

Heat Reflector

Figure 1

Tip Over Switch

Regulator

Safety Valve

Missing Parts? Please Call 866-676-1989 For Assistance


Hose

Ignition Hole

Regulator

Figure 2

Rear Guard




Features

32-TTC

Heat Reflector

Front Guard

Safety Valve

Tip Over Switch

Mounting Bolt Knob

Rear Guard

Features

47-TTC

Heat Reflector

Front Guard

Ignition Hole

Tip Over Switch

Regulator

Figure 3

© 2017, Pinnacle Climate Technologies, Inc. 5

Safety Valve

Hose

Mounting Bolt Knob

Propane Tank Top Heater User’s Manual

Model 32-TTC:

Tools Needed:

– Medium Phillips head screwdriver.

1. Place the tank collar bracket on top of the center plate. Be sure the mounting bolt knob is on bottom as shown in Figure 4

2. Insert machine screw into top hole using

Phillips head screwdriver.

3. Insert 2nd machine screw into bottom hole.

This will secure the tank collar bracket to the center plate.




Assembly

Model 47-TTC:

Tools Needed:

– Medium Phillips head screwdriver.

1. Insert the mounting bolt knob into the tank collar bracket.

2. Place tank collar bracket on the swivel bracket.

3. Place the plane washer on the tank collar bracket and then insert the support bolt.

(See Figure 5)

4. See Figure 6 on page 7 for determining burner position options.

WARNING DO NOT adjust burner heads while heater is operating.

Swivel

Machine

Screws

Wing Nut

Plane Washer

Mounting

Bolt Knob

Manifold

Figure 4

Fuel Connector Nut

Mounting Bolt Knob

Tank Collar Bracket

Swivel Bracket Fuel Connector Nut Tank Collar Bracket

Regulator

Knob

Figure 5

Missing Parts? Please Call 866-676-1989 For Assistance





Assembly

47-TTC (Continued):

– To have all 3 burners face front, the plane washer should be to the right side of tank collar bracket. (See Figure 6)

– To have far left burner face back, the plane washer should be to the left side of tank collar bracket. (See Figure 6)

Figure 6

Connecting Heater to LP Cylinder:

Be sure to read and understand all of the Safety

Information in this manual before connecting the heater to the LP cylinder. Installation must conform to local codes and with the Standard for the Storage and Handling of Liquefied

Petroleum Gasses and ANSI/NFPA 58.

Inspect the hose and regulator prior to each use of the heater. If there is excessive abrasion or wear, or if the hose is cut, replace it with the proper assembly shown in the parts list prior to using the heater.

Models 32-TTC / 47-TTC:

1. Be sure that the control knob on the regulator is in the “OFF” position.

2. Line up the slots in the tank collar bracket with the tank collar ring and slide into place.

Be sure the mounting knob is to the outside, and tighten.

3. Line up the threads on the fuel connector nut with the threads on the LP cylinder valve. Turn fuel connector nut COUNTERCLOCKWISE to tighten. Fully tighten the nut, being careful not to over tighten.

4. Slowly open the LP cylinder valve.

Model 16-TTC:

1. Be sure that the control knob on the regulator is in the “OFF” position.

2. Line up the threads on the fuel connector nut with the threads on the LP cylinder valve. Turn fuel connector nut COUNTERCLOCKWISE to tighten. Fully tighten the nut, being careful not to over tighten.

3. Slowly open the LP cylinder valve.


Check all connections for leaks using a 50/50 mixture of dish-soap and water. Any bubbles that appear show a leak. Remove and reconnect the Connector Nut to the valve .

WARNING

DO NOT direct the heater discharge towards any propane cylinder located within 20 feet of the heater.





Operation

Propane Supply / Information:

Propane (LP)

This heater is not supplied with a propane cylinder.

Use only an approved propane cylinder.

LP Characteristics

– Flammable, explosive under pressure, heavier than air and pools in low areas.

– In its natural state, propane has no odor, but for your safety an odor that smells like rotten cabbage has been added.

– Contact of propane (LP) gas with the skin can cause freeze burns.

– Heater is manufactured for use with propane gas only. DO NOT attempt to convert to any other gas. Such modifications are dangerous and will void the warranty.

– When heater is not in use, LP Cylinder must be turned OFF.

– Be sure that the LP Cylinder is located on a level and stable surface.

– DO NOT use this heater in a basement or below ground level. Propane is heavier than air and will always seek the lowest level. If you suspect a leak, shut off the valve at the LP

Cylinder immediately.

– The amount of Propane (LP) used with this heater varies. Both factors are

– The amount of gas in the cylinder of LP.

– The temperature of the LP tank and its surroundings.

CAUTION

Propane is safe to use when properly handled. Careless handling of the LP cylinder could result in a fire and or an explosion.

– Always keep LP cylinder fastened and upright.

– Avoid tipping the LP cylinder on its side when connected to a regulator, since this may cause damage to diaphragm in the regulator.

– Handle valves with care.

– Never connect an unregulated LP cylinder to a construction heater.

– DO NOT subject LP cylinder to excessive heat.

– Tightly close the gas shutoff valve on the LP cylinder after each use.

– All fittings must be protected when disconnected from the LP cylinder.

– Never store an LP cylinder inside a building or in the vicinity of a gas burning appliances.

The Propane (LP) cylinder must also be equipped with the following

– A collar to protect the gas valve.

– A shut-off valve terminating a LP cylinder valve outlet as specified in the American National

Standard for Compressed Gas Cylinder Valve

Outlets and Inlets Connections.

– A safety relief valve having direct communications with the vapor space of the LP cylinder.

– The heater must operate on vapor withdrawal from the operating cylinder.


CAUTION

The disconnected tank must never be stored in a building, garage or any other enclosed area.





Operation

Lighting Instructions:

Models 16-TTC / 32-TTC / 47-TTC

WARNING

Be sure to read and understand all of the Safety Information in this manual before lighting this heater.

CAUTION

Heater has high surface temperatures. Be sure to keep children, pets and clothing away from the heater. Be sure to keep burner and heater regulator clean and free from any debris. Maintain safe distances from heater as shown on Page 3.

DANGER

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

Ventilation

– Risk of indoor air pollution and Carbon

Monoxide Poisoning.

– Refer to Safety Information on pages 1-3 for information about Carbon Monoxide

Poisoning.

– ALWAYS provide a fresh air opening in the heated space of at least three square feet

(2,800 sq. cm) for each 100,000 BTU / Hr. of heater output. Provide a larger opening if more heaters are being used.

1. STOP! Be sure to read all of the Safety

Information (See pages 1-3).

– ALWAYS Stand to the side or rear of the heater.

– ALWAYS keep face and other body parts away from the heater.

2. Check that the valve and propane cylinder is open.

3. Turn the heater regulator knob CLOCKWISE to the (OFF) position.

4. Wait five (5) minutes for any gas to clear.

Smell for gas around the heater, including near the floor. If you do smell gas STOP!

Follow the safety instructions and check leaks. If there is no gas smell proceed to the next step.

WARNING

NEVER use a flame to check for leaks!

5. Turn the regulator knob

COUNTERCLOCKWISE to the “HI” position.

6. Insert a lit match into the ignition hole in the reflector. (See Figure 7)

7. Press the safety shut-off valve plunger for five

(5) seconds.

8. Mesh burner will light and glow red.

(Continued on Page 10)

Minimum Ventilation Opening Needed

16-TTC 32-TTC 47-TTC

0.5 ft.

2

460 cm 2

1.0 ft.

2

920 cm 2

1.4 ft.

2

1300 cm 2

Ignition Hole

WARNING

NEVER look over the top of the heater (reflector). There is a potential for a small flash of flame during ignition that can cause serious bodily injury.

ALWAYS stand to the side or rear of the heater during ignition. DO NOT allow any body part to touch the heater or be in front of the heater during ignition.

© 2017, Pinnacle Climate Technologies, Inc.

Safety Shut-OFF

Valve Plunger

Heat Regulator Knob

9

Figure 7


Lighting Instructions

Models 16-TTC / 32-TTC / 47-TTC (CONT)

9. Once lit, keep the plunger depressed for thirty

(30) seconds. Then release the plunger, and if the burner stays lit, remove and extinguish the match. You will know that the burner is lit when the mesh screen begins to glow red.

10. If the burner does not stay lit, repeat the lighting process. If the heater does not light after several attempts, be sure you are getting fuel to the burner. The faint smell of gas will tell you if the fuel is flowing. If not, there may be a problem with your LP cylinder. Take it back to your local dealer for replacement.

11. Once the burner is lit, turn Regulator Control

Knob to desired setting (HI) / (MED) / (LO ).

12. Light all burners when maximum heat is desired. Follow Lighting Instructions steps

1-11. The second and third burner should be lit separately. Do Not Attempt to light second burner off the first burner. Be sure NOT to point burners at one another.




Operation

To Turn Off Heater

1. Turn the valve on the LP cylinder CLOCKWISE to stop the flow of fuel.

2. Turn the heater regulator knob to the (OFF) position and wait at least fifteen (15) minutes for the heater to cool.

3. Tightly close the gas shutoff valve on the LP cylinder after each use.

4. Remove the heater from the LP cylinder by reversing the steps in Connecting Heater to

LP Cylinder on Page 7. DO NOT store the LP cylinder with the heater still attached or in an enclosed area.

NOTE: ALWAYS INSPECT HEATER BEFORE

USE AND AT LEAST ANNUALLY BY A

QUALIFIED SERVICE PERSON.

DANGER

EXTREMELY HOT during operation. Do Not touch any metal components while in operation. Keep gasoline and any other flammable liquids away from the heater.

DANGER

Never bring or store a propane cylinder indoors.

CAUTION mixing tube.

DO NOT insert the lit match into the air inlet holes in the

Maintenance and Storage

1. Inspect your heater before each use.

Check all connections for leaks, following the procedure outlined on Pages 7 and 8.

Check the Regulator Hose (dual burner models only) for any cracks, breaks or wear.

If the hose is damaged replace it with the correct manufacturers part. Heater should be inspected before each use and once annually by a qualified service person.

2. After use, always disconnect the heater from the LP cylinder, and store the heater separately from the tank. Be sure to close the tank valve after use, and before storage.

The LP cylinder should be stored outdoors in accordance with chapter 5 of the Standard for

Storage and Handling of Liquefied Petroleum

Gases (ANSI/INFPA 58).





Troubleshooting Guide

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag. It will begin with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your Se rial Number ready before calling customer service at 866-676-1989.

Problem

Unit will not light.

Possible Cause(s) Solution

1. Valve on propane cylinder closed.

1. Open cylinder valve by turning

COUNTERCLOCKWISE.

2. Propane cylinder empty.

3. Regulator not in (HI) position.

4. Defective regulator

2. Refill cylinder.

3. Turn regulator to (HI) position.

4. Replace regulator assembly.

Burner will not stay lit when gas valve plunger is released

1. Tip switch activated or defective.

2. Wire terminal connections unplugged.

3. Defective thermocouple.

4. Defective MPU.

1. Place heater in upright position or replace tip switch.

2. Check wiring connections.

3. Replace thermocouple.

4. Replace MPU.

Excessive flames coming out of burner, not glowing red. Flames flashback

/ burn inside the mixing tube.

1. Air inlet holes blocked or covered.

2. Burner screen damaged.

3. Gap between burner screen and burner can.

1. Clear any obstructions

2. Replace Burner screen.

3. Replace or repair burner head assembly.





Exploded View

4

1

2

3

Figure 8


Item

#

Description

2 Hose Assembly

7 Thermocouple

9 Mounting Bolt Knob

19 Tipover Switch




Parts list

16-TTC

‒

20-091-0002

‒

50-017-0001

32-TTC

20-051-0001

20-091-0002

20-503-0001

50-017-0001

47-TTC

20-051-0002

20-091-0002

20-503-0001

50-017-0001





LIMITED WARRANTY

P innacle Climate Technologies, Inc.

warrants this heater to the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided.

Pinnacle Climate Technologies, Inc. requires reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should keep your sales slip, invoice or cancelled check from the original purchase.

This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service within the warranty period, and which

Pinnacle Climate Technologies, Inc.

shall determine at its reasonable discretion.

This warranty does not apply to products purchased for rental use.

This Limited Warranty does not cover any failures or operating difficulties due to normal wear and tear, accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance and service by you or any third party. Failure to perform normal and routine maintenance on the heater, shipping damage, damage related to insects, birds or animals of any kind, and damage due to weather conditions are also not covered.

In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.

All transportation costs for the return of damaged product or parts will be the responsibility of the purchaser. Upon receipt of damaged item, Pinnacle Climate Technologies,

Inc. will examine the item and determine if defective.

Pinnacle Climate Technologies, Inc. will repair or replace and return the item, freight pre-paid.

If Pinnacle Climate Technologies, Inc. finds the item to be in normal operating condition, or not defective the item will be returned freight collect. This Limited Warranty is in lieu of all other express warranties. Pinnacle Climate

Technologies, Inc.

disclaims al warranties for products that are purchased from sellers other than authorized dealers or distributors.

AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS

WARRANTY EXPIRES,

Inc.

Inc.


Pinnacle Climate Technologies,

DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

APPLICATION. FURTHER, Pinnacle Climate Technologies,

SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER

OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE

INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle

Climate Technologies, Inc. assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives.

Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to you.

Pinnacle Climate Technologies, Inc. any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return or replacement of its equipment, and no such representations are binding on

Always be sure to specify the model number and serial number when making any claim with


Pinnacle Climate

For your convenience, use the space provided below to list this information.

does not authorize

Pinnacle Climate

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag. It will begin with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your Serial Number ready before calling customer service at 866-676-1989.

Serial Number Label

Model #:________________________________

Serial #:________________________________

Date of Purchase: ________________________


XXX-XXXXXXXX


1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (866) 676-1989

Fax: 320-251-2922 • Web: www.pinnacleclimate.com • Email: [email protected]

© 2017 Pinnacle Climate Technologies, Inc.

Remington REM-32-TTC-O 32000-BTU Portable Propane Tank Top Propane Heater User's Manual

PROPANE TANK TOP

HEATER

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

GENERAL HAZARD WARNING:

Table Of Contents

Safety Information

Safety Information

Specifications

Features

16-TTC

Missing Parts? Please Call 866-676-1989 For Assistance

Features

32-TTC

Features

47-TTC

Model 32-TTC:

Assembly

Model 47-TTC:

Missing Parts? Please Call 866-676-1989 For Assistance

Assembly

47-TTC (Continued):

Connecting Heater to LP Cylinder:

Operation

Propane Supply / Information:

Operation

Lighting Instructions:

Ventilation

Lighting Instructions

Operation

To Turn Off Heater

Maintenance and Storage

Troubleshooting Guide

Problem

Possible Cause(s) Solution

Exploded View

Parts list

Key Features

Related manuals

ProTemp

PT-16-TTC

BE

HLTT32

Pro-Temp

PT-32-TTC

Remington

REM-16-TTC-B

Remington

REM-32-TTC-O

Pinnacle International

Master MH-30-TTC

ProTemp

PT-TTC PT-30-TTC

ProTemp

PT-32-TTC

Craftsman

CMXEHAP60VGFA

ProTemp

PT-16-TTC

ProTemp

PT-18PNCH-A

Pinnacle

HS-32-TTC

Frequently Answers and Questions

What safety features does the Remington REM-32-TTC-O have?

Can I use the REM-32-TTC-O indoors?

What is the fuel consumption of the REM-32-TTC-O?

Table of contents