Rust-Oleum 266593, 266590SOS, 266579 Manual

Rust-Oleum 266593, 266590SOS, 266579 Manual
TECHNICAL DATA
PRO-14
PROFESSIONAL
2X DISTANCE MARKING PAINT SPRAYS
.DESCRIPTION AND USES
.
..PRODUCT APPLICATION
Rust-Oleum® Professional 2X Distance Marking Paint
Sprays are an aerosol coating packaged for use in an
inverted position as a marking paint. Use for marking
construction and excavation sites, underground utilities
and for traffic safety. This product is not water soluble and
withstands general weathering. These sprays are
recommended for use with Rust-Oleum® #2393000
Marking Wand and feature fast dry and adhesion to
concrete, blacktop, gravel, soil and grass.
APPLICATION
Shake can vigorously for one minute after the mixing ball begins
to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN.
Contact Rust-Oleum. Shake often during use. Hold can upright
6-8” from surface and spray in a steady back-and-forth motion,
slightly overlapping each stroke. Keep the can the same
distance from the surface. Keep the can in motion while spraying.
Apply two or more light coats a few minutes apart. Do not use
near open flame.
.APPEARANCE
.
DRY & RECOAT
.
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. Dries to touch
in 15 minutes and is fully dry in 8 hours.
Flat to semi-gloss finish (dependent on surface porosity).
.PRODUCTS
SKU
266574
266575
266577
266579
266590
266591
266592
266593
266594
.
Description
Fluorescent Green
Caution Blue
High Visibility Yellow
Fluorescent Orange
Fluorescent Red-Orange
Safety Red
Fluorescent Pink
White
Clear
CLEAN-UP
When finished spraying, clear spray valve by turning can upright
and pushing spray button for 2-3 seconds. Clean-up wet paint
with xylene or mineral spirits. Properly discard empty container.
Do not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a solvent
such as mineral spirits. Do not insert any object into can valve
.PACKAGING
.
15-ounce containers, 6 containers/carton
..PAINTING CONDITIONS
.
Use when temperature is 40-90°F (4-32°C) and humidity is
below 85% to ensure proper drying. Avoid spraying in very
windy, dusty conditions. Protect surrounding surfaces from
overspray. Overspray can carry a significant distance.
..PRODUCT APPLICATION
.
SURFACE PREPARATION
Remove excessive loose debris from the surface before
application of the coating.
1
Form: GDH-156
Rev.: 100115
TECHNICAL DATA
PROFESSIONAL 2X DISTANCE MARKING PAINT SPRAYS
PHYSICAL PROPERTIES
.
2X DISTANCE MARKING PAINT SPRAYS
Resin Type
Modified Alkyd
Pigment Type
Varies with color
Solvents
Acetone, Aliphatic Hydrocarbons
Fill Weight
15 ounces
MIR
1.20 Max
Practical Coverage at Recommended DFT
(assumes 15% material loss)
Dry Times at 70-80°F
(21-27°C) and 50%
Relative Humidity
Up to 800 linear feet (243 meters) at 1.5 in wide (3.8 cm)
Depending on surface porosity
Touch
15 minutes
Fully Dry
8 hours
Shelf Life
5 years
Flash Point
-156°F (-104°C)
Safety Information
For additional information, see SDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature
do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we
can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All
technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-61
Rev.: 100115
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement