Quoizel PWL1613WT Powell 13-in W Western Bronze Outdoor Flush Mount Light Assembly Instructions
Advertisement
Advertisement
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Assembly Instruction Sheet #IS-PWL1613WT
For Style PWL1613WT
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended: (3) Medium Base 75W Maximum
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
Part
A
B
E
F
C
D
G
H
I
J
K
Description
Crossbar
Short Nipple
Lock Washer
Hex Nut
Flat Washer
Hex Coupling
Rubber Washer
Finial
Ceiling Canopy
Shade
Center Stem
Quantity
1 pc.
1 pc.
2 pcs.
2 pcs.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
A
G
H
B
C
D
E
F
J
I
K
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
2012 QuoizelInc.
October2012
1of5
PWL1613WT
FINISH: WESTERN BRONZE
2.4mm
13Ga
GND
QUOIZEL
R
1
2
13”
4”
6”
10” 13”
10”
13”
(3)75W Medium
Base Bulbs
(Not Supplied) NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2
"
NO.
PART NUMBER
1
2
11613WTPWL
G3414SH
REPLACEMENT PART DESCRIPTION
BASE WESTERN BRONZE PWL1613WT
SQUARE WHITE GLASS 10"SQ
2of5
REQ.
1
1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-PWL1613WT
For Style PWL1613WT
STEP 1
-
Attach Crossbar to Outlet Box
A. Secure the Crossbar (A) to the outlet box with outlet box screws (not supplied). Tighten until snug.
Figure 1
Outlet Box
Mounting
Hole
Crossbar
Outlet Box
Screw (not
Supplied)
STEP 2
-
Attach Nipple to Crossbar
A. Locate the Nipple (B) and thread one Hex Nut (D) onto it about half way. Slip a Lock Washer (C) onto it and thread one end of the Nipple (B) into the center hole of the Crossbar (A).
B. Position the Ceiling Canopy (I) over the outlet box, passing the mounting hole in the center of the Ceiling
Canopy (I) over the end of Nipple (B).
C. Adjust the Nipple (B) so approx 3 8 inch of the Nipple
(B) is protruding from the mounting hole. This adjustment may take a few tries.
D. When this length is achieved, remove the Ceiling
Canopy (I) and tighten the Hex Nut (D) up against the underside of the Crossbar (A) with pliers.
Figure 2
Ceiling Canopy
Crossbar
Lock Washer
Hex Nut
Nipple
STEP 3
-
Adjust Hex Nut
A. Thread one Hex Nut (D) onto the other end of the nipple
(B). Thread this Hex Nut (D) on just enough so the inside surface of the Ceiling Canopy (I) rests against it.
* You may have to trial fit the Ceiling Canopy (I) one more times to insure this distance also. This Hex Nut
(D) is needed here to prevent you from crushing down the center of the Ceiling Canopy (I).
Figure 3
Ceiling
Canopy
Crossbar
Nipple
Hex Nut
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
2012 QuoizelInc.
October2012
3of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-PWL1613WT
For Style PWL1613WT
STEP 4
-
Make Wire Connections
A. Use standard wire connectors to make all wire connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.
Figure 4
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Ground wire from supply
Black wire from fixture
Ground wire from fixture
Figure 5
STEP 5
-
Attach Ceiling Canopy
A. Position the Ceiling Canopy (I) to the ceiling by passing the Nipple (B) through the center hole.
B. Slip on the Flat Washer (E) and the Lock Washer (C) and then thread the Hex Coupling (F) to the bottom end of the Nipple (B). Snug down assembly until the Ceiling
Canopy (I) is flush against the ceiling.
* Be sure that there are no trapped or pinched wires along the edge of the Ceiling Canopy (I).
Ceiling
Canopy
Crossbar
Nipple
Figure 6
Flat
Washer
Lock Screw
Hex Coupling
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
2012 QuoizelInc.
October2012
4of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-PWL1613WT
For Style PWL1613WT
STEP 6
-
Attach Center Stem to Socket
Assembly
A. Thread Center Stem (K) to the Hex Coupling underside of the Ceiling Canopy (I). Hand tighten until snug.
Ceiling Canopy
Hex Coupling
Center Stem
Figure 7
STEP 7
-
Install Bulb
A.
This fixture uses standard bulb with a medium screw base . Maximum 75 watts.
B. Insert bulb and screw snugly into place.
Socket
Bulb
Figure 8
STEP 8
-
Install Shade
A. Place the Shade (J) and Rubber Washer (G) over the end of the Center Stem (K). Secure by threading the Finial(H) onto the Center Stem (K). Hand tighten until snug.
Your fixture is now assembled and ready to use.
Enjoy!
Center Stem
Shade
Rubber Washer
Finial
Figure 9
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
2012 QuoizelInc.
October2012
5of5
Advertisement