SSeries 10119A1-BN, 10119A1-NB, 10119A1-DRN-NB, 10119A1-DRN-BN Installation guide

SSeries 10119A1-BN, 10119A1-NB, 10119A1-DRN-NB, 10119A1-DRN-BN Installation guide
Basin Faucet
DIMENSION DRAWINGS: 06
3-3/4"
06
3-3/4" a
124 =
Wu 4-7/8" +
= 32 == it
== 1/4" == 1/4"
YOU MAY NEED
\\//
=
PARTS:
| Component
| Handle
| Canopy
| Screw
| Cap
| Press Hat
Cartridge
O-Ring
Cartridge Holder
Body
| Base
| O-Ring
| Screwed Connecter
| Washer
| Washer
| Lock Nut
| Flexible Hose
| Aerator
a a | zZ
HOPOMNOUAONHZ
Ree ea |->
ЧМ ол А о
TROUBLE-SHOOTING
If you've followed the instruction carefully and your faucetstill does notwork properly,
Problem
Cause
Leaks underneath handle.
Aerator leaks or has an
inconsisitent water flow
pattern.
Cartridge has come loose.
take these corrective steps.
Action
Tighten the cartridge.
Aerator is dirtyor worn
out or misfitted.
Unscrew the aerator to
clean orreplace washer,
or replace the aerator
Water will not shut off
completely.
==
Dirty orworn outwasher
in cartridge.
Remove handle and cartridge
to checkif thewasher is damag
permanently or dirty. Re-install
cartridge.
== |
INSTALLATION PROCEDURES
и
_
You should clean all the dirts from valve outlets.
Turning off the water supply valves. This is usually
found near the water meter. If you are replacing
an existing faucet, remove the faucet from the
sink and clean the sink surface thoroughly.
Install without Deck Plate. Make sure the O-RING
is placed onto the bottom of Base Ring. Install
faucet through hole in sink. From underside sink,
put Plastic Washer and Mounting Nut. Position
faucet on sink properly and tighten Mounting Nut.
Lo
||
Install with Deck Plate. Place a bead of plumber's
putty between faucet and sink. Place Deck Plate
over the three holes of sink. From underside sink,
tighten Wing nut.
Make sure the O-RING is placed onto the bottom
of Base Ring. Install faucet through Deck Plate.
From underside sink, put Plastic Washer and
Mounting Nut. Position faucet on sink properly
and tighten Mounting Nut.
's #4
e
If necessary, tighten screws using a adjustable
wrench until the faucet is firmly connected to the
sink.
Connect hot and cold water supply lines to the Water
Supply Valves.
ss: —
Unscrew Locknut. Make sure the Rubber Washer in
the right position under Flange. Insert Pop-up
Assembly into Sink drain Hole. From underneath,
tighten with Lockset.
Open
iy
“a
“.
=f
Warning!!!
‘Do not over-tighten nut during installation.
‘Over-tighten may crack the valve and cause severe leak.
Valve Cartridge Removal Maintenance
CS
Ta
Remove handles. Unscrew Dome Cap counter clockwise
by hand. Unscrew Retaining Nut using adjustable wrench,
take out cartridge assembly and inspect. Replace parts
as necessary. Reassemble parts by reversing steps.
Lift the handle up, the cartridge will be activated
allowing water to flow. The water flow will increase
by continuing to rotate handle. By rotating the
handle to the right, the water temperature will
decrease to cold flow only. By rotating Handle to
the left, the water temperature will increase to hot only.
Faucet Start Up
After installation is complete, remove aerator and rotate
handle to the closed position. Turn on the water supply
valves, and check all connections for a leak. Turn on
your faucet and allow both hot and cold water to run at
least one minute each. Replace Aerator.
Handle Removal Maintenance
“aw
Turn off water and relieve pressure! Detach handle button
using a small flathead screwdriver, unscrew set screw
using Allen Wrench and take off handle.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement