Home Decorators Collection HL1309-50 EIR Verdugo Oak 8 mm Thick x 7.64 in. Wide x 47.80 in. Length Laminate Flooring (1521 sq. ft. / pallet) Installation Guide

Home Decorators Collection HL1309-50 EIR Verdugo Oak 8 mm Thick x 7.64 in. Wide x 47.80 in. Length Laminate Flooring (1521 sq. ft. / pallet) Installation Guide
Installation Instructions
Laminate Click-Lock Flooring
For Assistance,
Call: 1-800-986-3460
Homedepot.com/homedecorators
Products Description
8mm Click
Verdugo Oak
Laminate Flooring
Grade Levels
Above Grade / On Grade
Below Grade
Installation Method
Glueless installation
Model #HL1309
Item # 1002584106
MANUFACTURER’S REQUIRED MINNESOTA DISCLOSURE -IMPORTANT HEALTH NOTICE: SOME OF THE BUILDING MATERIALS USED IN THIS HOME (OR THESE BUILDING MATERIALS) EMIT
FORMALDEHYDE. EYE, NOSE, AND THROAT IRRITATION, HEADACHE, NAUSEA AND A VARIETY OF ASTHMA-LIKE SYMPTOMS, INCLUDING SHORTNESS OF BREATH, HAVE BEEN REPORTED AS
A RESULT OF FORMALDEHYDE EXPOSURE. ELDERLY PERSONS AND YOUNG CHILDREN, AS WELL AS ANYONE WITH A HISTORY OF ASTHMA, ALLERGIES, OR LUNG PROBLEMS, MAY BE AT
GREATER RISK. RESEARCH IS CONTINUING ON THE POSSIBLE LONG-TERM EFFECTS OF EXPOSURE TO FORMALDEHYDE.
REDUCED VENTILATION MAY ALLOW FORMALDEHYDE AND OTHER CONTAMINANTS TO ACCUMULATE IN THE INDOOR AIR. HIGH INDOOR TEMPERATURES AND HUMIDITY RAISE FORMALDEHYDE
LEVELS. WHEN A HOME IS TO BE LOCATED IN AREAS SUBJECT TO EXTREME SUMMER TEMPERATURES, AN AIR-CONDITIONING SYSTEM CANBE USED TO CONTROL INDOOR TEMPERATURE LEVELS.
OTHER MEANS OF CONTROLLED MECHANICAL VENTILATION CAN BE USED TO REDUCE LEVELS OF FORMALDEHYDE AND OTHER INDOOR AIR CONTAMINANTS.
IF YOU HAVE ANY QUESTIONS REGARDING THE HEALTH EFFECTS OF FORMALDEHYDE, CONSULT YOUR DOCTOR OR LOCAL HEALTH DEPARTMENT.
WARNING: CALIFORNIA RESIDENTS: This product can create wood dust and emit formaldehyde of which are known to the State of California to cause cancer.
CAUTION: ASBESTOS IN EXISTING FLOOR: Home Decorators Collections product does not contain asbestos. Existing installed resilient flooring and asphaltic adhesive may contain asbestos
fillers or crystalline silica. Do not sand, dry sweep, dry scrape, drill, saw, bead-blast, or mechanically chip or pulverize existing resilient flooring, backing, lining felt, asphaltic “cutback” adhesive or
other adhesive. See “Recommended Work Practices for Removal of Resilient Floor Coverings” (rfci.com) for detailedinformation and instructions on removing all resilient covering structures.
CAUTION: WOOD DUST: Sawing, sanding and machining this product can produce wood dust. It can cause respiratory, skin and eye irritation. Avoid prolonged exposure to wood dust.
Power tools should be equipped with a dust collector. If possible, perform wood dust generating activities outdoors. If high dust levels are encountered, use an appropriate NIOSH-designated dust mask.
Safety and Health Precautions
Power tools can be dangerous. Operate in strict accordance to manufacturer’s operating instructions and safety precautions. Unsafe and improper use can cause serious injuries. Avoid inhalation and
exposures to wood dust by mechanical means and by wearing personal protective equipment. Wear appropriate personal protective equipment (PPE) which includes NIOSH or OASH-approved dust masks,
safety goggles and work gloves.
Warranty
This flooring product comes with a manufacturer Limited Wear Warranty. The warranty applies to the original purchaser of the flooring. It warrants the original purchaser that the finish surface will not
wear through for the duration of the stated warranty from the date of purchase. Contact our Customer Service Team at 800-986-3460 to request a written copy which provides detailed terms of
coverage and limitations.
Pre-Installation
OWNER/INSTALLER RESPONSIBILITY
The owner is advised to be at home during the installation for consultation/direction. The owner and
installer should discuss installation and layout to maximize satisfaction. If this is not possible,
consultation should be done prior to installation. Installers should be familiar with installation guidelines
from National Wood Flooring Association (woodfloors.org). The owner/installer assumes all responsibility
for product quality of completed installation.
PERFORM PRE-INSTALL INSPECTION. FOR CLAIMS PURPOSES, YOU ARE ALLOWED TO OPEN
UP TO 4 BOXES FOR PRODUCT INSPECTION. DO NOT OPEN ALL THE BOXES. OPENING ALL
THE BOXES CONSTITUTES YOUR ACCEPTANCE OF THE PRODUCT. INSPECT ALL THE PLANKS
IN THESE 4 BOXES CAREFULLY. EXAMINE FLOORING FOR COLOR, FINISH AND QUALITY.
IF YOU DISCOVER THAT PRODUCTS ARE DEFECTIVE, OR IF MATERIAL IS QUESTIONABLE,
YOU SHOULD CONTACT THE RETAILER. IF YOU ARE SATISFIED, PROCEED WITH INSTALLATION.
Prior to installation, arrange planks from several boxes to ensure even distribution of colors, shades and
characteristics in the installed flooring.
Purchase flooring to be installed in one large area at the same time. Product purchased at a later time
than the first purchase may vary beyond your expectations.
Accessories, trims and moldings are manufactured to coordinate with the varied appearances of the floor
planks. Any exact matches are coincidental. Non-matching accessories are not defective products.
This product is manufactured according to strict quality standards. In the event that defects are
discovered in the field, the industry standards permit a defect tolerance not to exceed 5%. Order an
additional 5% extra for cutting wastage and grading allowances (10% for diagonal installations).
During installation, inspect the planks continuously. Defects that can be seen from a standing position
should be cut off or held out. Installing defective planks implies acceptance.
Squeaking and clicking noises are the result of interactions among flooring, joists and subfloors when
they move. Limiting the movements of the flooring system usually eliminates most of these noises.
Sometimes, it is impossible to eliminate them completely and minor squeaking or clicking noises are to
be accepted as normal flooring phenomenon.
Minor scratches can generally be repaired with the use of putty, stain or filler. It is an industry standard
practice of flooring installation and it should be accepted as normal by the home owner.
To assure the warranty is not inadvertently voided, before proceeding with any activity that is not
covered in this manual, please contact our Customer Support Team at 800-986-3460.
CONCRETE SUBFLOOR REQUIREMENTS
Concrete subfloors must:
□ Have minimum rated strength of 3000psi.
□ Be level to within 1/8 in. in a 6 ft. span or 3/16 in. in a 10 ft. span; no bumps or low spots.
High spots can be removed by grinding; depressions can be filled with patching compound
formulated for use in floor installation.
□ Be clean; no construction debris, soil, mud and any other objects on or adhering to the floor;
if necessary,scrape and sweep away before the installation; no protrusions of nails, debris, metals
should remain.
□ New concrete slab must cure for at least 60 days. It must have a minimum 10 mil polyethylene
sheet between the ground and the concrete.
□ Be free from moisture related conditions which can damage the installed flooring.
CONCRETE MOISTURE
Test all concrete subfloors for moisture content and document the results. Visual checks are not reliable.
Perform tests at locations around exterior doorways, near walls containing plumbing, near foundation
walls and in the center of the room. Minimum sample size is 3 samples per 1000 sq. ft. of area and one
test for every additional 1000 sq. ft. thereafter.
Moisture content should meet one of the following criteria:
□ 5% when tested using Tramex Concrete Moisture Encounter.
□ Less than 3 pounds per 1000 sq. ft. per 24 hours when using Calcium Chloride test (ASTMF1869).
□ 75% when using Relative Humidity Testing (ASTMF-2170).
NOTE: Concrete moisture content may be acceptable the time of the test. These tests do not
guarantee a perpetual “dry” concrete slab. The concrete slab moisture content can vary at other
times of the year. We are not responsible for moisture-related damage to installed flooring.
WOOD SUBFLOOR REQUIREMENTS
The subfloor must be clean; no presence of construction debris, soil, mud and any other objects on or
adhering to the floor; no protrusions of nails, debris, or metals should remain. If necessary, scrape and
sweep the subfloor before the installation.
The subfloor must be structurally sound and stable; no movements or squeaks; no loose panels or loose
nails; no signs of ply de-lamination or other damages. Repair all shortcomings before installation.
The subfloor must be flat; no visible bumps or low spots; the subfloor should be flat to within 1/8 in. in 6 ft.
span or 3/16 in. in 10 ft.. Test for moisture using a reliable moisture meter. Perform tests at locations
around exterior doorways, near foundation walls, near walls containing plumbing lines and in the center
of the room. Measure 20 locations per 1000 sq. ft. Moisture content of the subfloor should be less than
12%. Moisture content difference between the subfloor and flooring should be 2% or less.
PLYWOOD OR ORIENTED STRAND BOARD (OSB) SPECIFICATIONS
On truss/joist spacing of 16 in. (406 mm) O/C or less, the industry standard for single-panel subflooring
is a minimum 5/8 in. (19/32 in., 15.1 mm) CD Exposure 1 plywood subfloor panels (CD Exposure 1) or
23/32 in. OSB Exposure 1 subfloor panels, 4 ft. x 8 ft. sheets. Expansion gap between panels should be
1/8 in. (3 mm). If panels are not tongued and grooved and there is not sufficient spacing or is inadequate,
cutintherequiredspacingwithacircularsaw.Donotcutinexpansionspaceontongueandgroovepanels.
PARTICLE BOARD OR FIBER BOARD
Only for floating installation.
EXISTING FLOORS
Installation over existing floor requires the installer to consider potential issues related to
moisture damage, adhesive failure and fastener failure. Contact the adhesive and fastener
manufacturers respectively for their specific instructions, recommendations and requirements.
Acceptable floor coverings include: solid hardwood, linoleum, terrazzo, ceramic tile and
other “moisture sealing floors.”
Unacceptable floor coverings include: carpet, needle punch felt, edge glued linoleum and
other “moisture absorbing flooring.”
JOB SITE CONDITION
Prior to installation, the installer must ensure that at the time of installation, the job site
conditions including subfloor/substrate, ambient temperature and relative humidity, and all
impacting variables will not negatively affect the floor. The manufacturer will decline
responsibility for damages associated with improper installation or poor site conditions.
STORAGE AND CONDITIONS
Do not store flooring in uncontrolled environmental conditions. For example, garages and
exterior patios are not acceptable areas to store flooring. Handle and unload flooring with
care and store within the environmentally controlled site in which it is expected to perform.
Flooring stored on a concrete slab should be elevated at least4 in.to allow air circulation
under cartons.
EXISTING HOME
An existing home should have a consistent room temperature of [ 60°F-80°F and relative
humidity (RH) of 35%-60%]. Continual deviation from these conditions will affect the dimensions
of flooring. When using a heater during winter months, humidity may be much lower than the
acceptable range. A humidifier is recommended to prevent excess shrinkage in flooring due to
low humidity levels. During the warmer months, maintain humidity levels using an air conditioner,
dehumidifier, or by turning on your heating system periodically.
NEW CONSTRUCTION OR REMODEL
All work involving water, such as pouring basement concrete floors, drywall and plasterwork,
plumbing, etc. must be completed well in advance of the floor delivery. Ensure that the building
is enclosed. Where building codes allow, permanent heating and/or air conditioning systems
should be operating at least five days preceding installation and should be maintained during
and after installation. If it is not possible for the permanent heating and/or air conditioning
system to be operating before, during and after installation, a temporary heating and/or
dehumidification system that simulates normal living (occupied) conditions can enable the
installation to proceed until the permanent heating and/or air conditioning system is fully
operational. Your job site should have a consistent temperature of [ 60°F-80°F and relative
humidity (RH) of 35%-60%] which should be maintained continuously thereafter.
BASEMENTS AND CRAWL SPACES
Concrete slab or ground must be dry. Ensure that crawl spaces have open vents year-round
for proper air circulation and prevent moisture build up. The ground in the crawl spaces must
be completely covered using 6 mil black polyethylene. Crawl space clearance between the
earth and underside ofjoists should be no less than18 in.and the perimeter of the vent area
should be equal to 1.5% of the total square footage of the crawl space or as mandated by code.
RADIANT HEATED SUBFLOOR
This product can be installed over radiant heated subfloor. The radiant heatsystem should
be operational for at least 7 days before beginning installation. Turn off heat to allow the
subfloor to cool down to room temperature 3-4 hours before beginningthe installation.
Increase temperature gradually after installation. Operating surface temperature must not
exceed 85°F (29°C). Contact heater manufacturer for specific installation instruction.
Consult with the radiant heat system manufacturer to ensure that the system iscompatible.
MOISTER BARRIER/UNDERLAYMENT PADDING
CONCRETE SUBFLOOR
When installing over a crawl space or concrete slab, it will be necessary to use a moisture
barrier to prevent moisture migration. A plastic film with a minimum thickness of 6 mil should
be placed with a 4 –6 in. (101.6 –152 mm) overlapped seam, and taped with a suitable tape,
this should be combined with an approved underlayment padding for floating floors.
For direct glue installation, use a moisture barrier if moisture levels exceed the requirement
(see Concrete Moisture section).
SOUND CONTROL UNDERLAYMENT
It is optional. Check with sound control manufacturer for application guidelines.
Generally, the less compressive underlayment is preferred.
EXPANSION GAP
Required gap width range is 5/16 in. to 3/8 in.It is required around the perimeter of the floor
and between floor and all vertical obstructions. Do not place permanently mounted structures
such as kitchen counter/cabinet on the installed floor.
TRANSITION MOLDING
Floating installation, transition T-molding is required in the following cases: floor spanning
greater than 40 feet in length or width; doorways or passageways 5 ft. wide or less.
Note: Floor areas interrupted by wall openings greater than 5 ft. wide, or interrupted by
wall sections extending out of the wall, or floor areas which are not rectangular may
experience buckling or gapping if there is excessive floor expansion or shrinkage.
TOOLS AND MATERIALS BASICS
• Tape measure • Moisture meter (wood, concrete or both) • Chalk line & chalk • Hammer
• Electric power saw • Carbide tipped saw blade for fine cut • NIOSH-designated dust mask
• Handsaworjambsaw • Eyeprotection • Straight edge or Spacers • Pry Bar • Mallet
• Broom • Color matched wood putty •Tapping block • Pull bar • Painters tape
Helpful Pointers
GENERAL TIPS
□
□
□
□
Make sure your work area is well lit. Good visibility ensures that color is consistent and that visually defective planks are detected and removed.
The remainder of the last plank can be used as a starter board on the following rows.The minimum length of the first and last plank needs to be longer then the width of the material being installed.
Using a shorter piece at under cut door jams will help when fitting flooring in place.
Never hit the flooring directly with the tapping block and be careful not to fracture floor edges.
CUTTING THE LAST ROW TO WIDTH
□ Most often the entire length of the last row will need to be cut so that it is narrow enough to fit the remaining space.
□ Measure the distance between the floor face edge (exclude the tongue) to the wall. Subtract [ 5/16 – 3/8 in.] from this measurement for expansion gap. Draw a line. Cut through the line.
Discard the excess piece. Proceed with the installation.
Preparing for Installation
□ Ensure subfloors are clean.
Lay out several cartons. Randomly arrange planks to ensure good color and shade
mixture and end joint spacing. Inspect plank quality and grading Lay out trim moldings in
advance and find planks whose shade closely matches. Set these aside for future use.
□ Remove the existing base, shoe molding or threshold carefully. They can be used to cover
the 5/16 – 3/8 in. expansion gap left around the edge of the room.
□ Undercut doors and casings using a handsaw laid flat on a piece of scrap flooring.
□ Install the underlayment (if used) parallel to the flooring according to the underlayment
manufacture instruction. Any overlap (top) should be on the same side as the groove of the
flooring so that the floor planks will slide smoothly into place. Tape all seams. Secure the
underlayment material as necessary to prevent excessive movement.
Installation
1. INSTALLING THE FIRSTROW
a. Remove the tongue from the width and length of
the first plank. Be sure to allow enough space for
the 5/16 –3/8 in. expansion gap.
b. Saw off the tongue from only the length of the
remaining planks to be installed in the firstrow.
1.1
2.1
2.2
2.3
2.4
2.5
2.6
3.1
2. INSTALLING THE SECOND AND REMAINING ROWS
a. Follow the procedures shown in Figures 2.1 - 2.3 for
the first three rows; you can then push these three
completed rows into place along the wall.
Be sure to use spacers or scrap pieces of flooring
along the wall to maintain the expansion gap.
At this point, you can avoid a stair step joint pattern
by using the pieces of boards cut off when finishing
a row (or cut new ones). Be sure these pieces are
at least 6 in. long. Always keep the end joints at least
6 in. apart. You can then finish the room as shown
in Figures 2.4 –2-.6.
3. INSTALLING THE LASTROW
a. Use the pull bar to draw the last row to fit tightly to
the previous row (as Figure 3.1shows)
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance
Installation Instructions
Laminate Click-Lock Flooring
For Assistance,
Call: 1-800-986-3460
Homedepot.com/homedecorators
Products Description
8mm Click
Verdugo Oak
Laminate Flooring
Grade Levels
Above Grade / On Grade
Below Grade
Installation Method
Glueless installation
Model #HL1309
Item # 1002584106
Accessories
Pictures are for general illustrative purposes only. Actual products may differ from diagrams.
Clean the floor.
Use matching putty where necessary.
Install or reinstall all wall trim pieces. Nail them through the wall, but not to the subfloor to avoid restricting the expansion gap.
Install transition trim pieces. Nail them to the subfloor, not the flooring.
At doorways, transitions should be used to protect the edges of the floor and to provide a decorative transition from one floor type to another.
If the floor is to be covered, use a breathable material such as cardboard. Do not cover with plastic.
FLOORING
FLOORING
FLOORING
T-Molding: Used to create a transition between floor
coverings of similar heights or to cover an expansion gap
HARD SURFACE
REDUCER
RESILIENT
FLOOR
FLOORING
Hard Surface Reducer: Used to transition to another
hard surface flooring of different heights such as tile,
vinyl, or concrete.
STAIR NOSE
STAIR TREAD
RISER
Stair Nose: Used in conjunction with flooring installed on
stair steps or finished edges of a higher level floor like in
a sunken living room.
WALL BASE
FLOORING
Wall Base: Used to give a finished look at the base of
the walls. It can be used with or withoutquarter round.
CARPET REDUCER
FLOORING
CARPET
Carpet Reducer (also called Baby Threshold or End Cap):
Used to transition floor coverings of differing heights.
This reducer strip is also commonly used to border a fireplace,
sliding glass door and other exterior door jambs.
WALL
T-MOULDING
WALL
□
□
□
□
□
□
QUARTER ROUND
FLOORING
Quarter Round: Used to cover the expansion space between
the wall base and your flooring. It can also be used to make
smooth transitions between the floor and cabinetry.
It can be used with or without wall base molding.
Care and Maintenance
DAILY MAINTENANCE
□ Sweep, dust, mop, or vacuum your floor regularly to remove any particles that could cause abrasion or scratch your floor.
CAUTION: Vacuums with a beater bar or power rotary brush head can damage a floor and should never be used.
□ Use a damp mop to remove spots and soil. Apply appropriate cleaning solution to the cleaning cloth / mop. Do NOT apply directly to the floor.
□ For lightly soiled areas, clean with distilled water.
□ For moderately soiled areas, use a mild solution of isopropyl (rubbing) alcohol and distilled water. Dilute the mixture by mixing one part alcohol and 2 parts distilled water. For tougher spots, use a
higher concentration of isopropyl alcohol and distilled water. For extreme cases, a solution of nail polish remover and distilled water can be used.
□ HINT: For best results, clean the floor in the same direction of the planks. When the cleaning cloth/mop becomes soiled, rinse or replace it with a clean one. Following up with a clean, dry cloth will
remove residual streak marks and spots.
□ DO NOT leave any amount of liquids (water, juice, soft drinks, spills, etc.) on the floor. Clean any wet spots immediately.
□ DO NOT use a steam cleaner.
□ DO NOT use a wet mop or douse the floor with water or liquid cleaners. Liquid can seep between the cracks and cause moisture damage.
□ DO NOT use any cleaning agents containing wax, oil or polish. Left over residue will form a dull film.
□ DO NOT use steel wool or scouring powder which will scratch the floor.
BRANDED OR OFF-THE-SHELF FLOOR CAREPRODUCTS
If none of the above are effective and you choose to use a store bought product, test the product in a non-conspicuous area (i.e., closet, corner, or scrap pieces) for potential adverse side effects.
PREVENTATIVE MAINTENANCE
□
□
□
□
□
□
□
□
Protect your floor when using a dolly for moving furniture or appliances. Protective sheets and/or plywood may be needed. Never slide or roll heavy furniture or appliances across the floor.
Place protective pads beneath furniture legs and other heavy objects.
Avoid excessive exposure to water from being tracked in during periods of inclement weather.
Minimize abrasive material and dirt by placing mats on both sides of exterior doors and by using area rugs in high-traffic areas.
Rearrange furniture and rugs periodically to avoid uneven color and shade changes from light exposure.
Use protective mats beneath rolling chairs and keep furniture casters clean.
Keep pets’ nails trimmed.
Remove shoes with cleats, spikes or exceptionally pointy heels before walking on the floor.
CLIMATE MAINTENANCE
□ Care should be taken to control humidity levels within the 35%-55% range. Flooring, especially hardwood and bamboo, dimensions will be affected by varying levels of humidity.
□ Dry Climates: Ahumidifier is recommended to maintain humidity levels. Wood stoves and electric heat tend to create very dry conditions during the winter months.
This also will cause shrinkage inflooring.
□ Humid, Wet Climates: By using an air conditioner, heater, or dehumidifier, proper humidity levels can be maintained to prevent excessive expansion due to high moisture content.
FLOOR REPAIR
□ Very light and small surface scratches can be repaired with a staining “touch up” pen of the appropriate color.
□ Slightly deeper scratches can be repaired by means of colored putty or stains. Fill the scratches with the putty. Level with putty knife. Wipe off excess putty.
□ Very deep scratches may require the replacement of the planks.
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement