a
DESIGN
al.
HOUSE
ASSEMBLY INSTRUCTIONS
Espresso & White Two Door Two Drawer
Vanity Base Cabinet
Part #: 559039
559070
Unpacking Precautions
If using a sharp object to unpack the vanity components and the packing materials,
be careful to avoid scratching or damaging the vanity components. The various
packing materials may be used to protect the vanity components during assembly.
During the unpacking process, place the various components away from and to the
side of the work area so that they will not be inadvertently knocked over or
otherwise damaged.
Required Tools
Phillips Screwdriver
Rubber Mallet
Wood Glue
PARTS LIST
FRONT PANEL 1PC
RIGHT SIDE PANEL 1PC
LEFT SIDE PANEL1PC BOTTOM PANEL 1PC
as
SUPPORT PANEL 1PC
BACK PANEL 1PC TOE KICK 1PC
DRAWER BACK PANEL 2PCS
DRAWER BOTTOM PANEL 2PCS A
DRAWER FRONT PANEL 2PCS
DRAWER SIDE PANEL 4PCS
HARDWARE LIST
6,00
o o
9
A
a
ve —
\
AN
AY
0
©
a(R). EXTERIOR PART OF GLIDE 2PCS b(R).
X
INTERIOR PART OF GLIDE 2PCS
se N ©
a(L). EXTERIOR PART OF GLIDE 2PCS b(L).
c. KNOB 4PCS d. WOODEN TRIANGLE 4PCS
5]
N
f. GLIDE BRACKET 4PCS g. 1/2" FLAT (ROUND)H
ROUND HEAD SCREW
ONLY
£ sv» SSS
az
SY
/
INTERIOR PART OF GLIDE 2PCS
e. RUBBER BUMPER 12PCS
EAD SCREW 50PCS
FOR ESPRESSO METAL CLIP
i. 1-1/8" FLAT HEAD SCREW
7PCS (3 PCS FOR ATTACHING
THE BACK PANEL TO THE
BOTTOM PANEL, 4PCS FOR
CONNECTING TO THE
COUNTERTOP)
k. KNOB SCREW FOR DRAWER 1-1/2" 2PCS
j. KNOB SCREW FOR DOOR 1" 2PCS
Step 1
Lay the face frame with doors (A) on the soft surface, doors facing down.
Step 2
Attached rubber bumpers to both the top and bottom of each door where they make
contact with the face frame to prevent damage and reduce noise.
Step 3
Using the wood glue, squeeze a small bead of glue in all grooves before assembling the
cabinet sides, bottom, top and back panels. Be careful not to use too much glue, this could
cause access glue to squeeze out and onto the panels, if this should happen, be sure to
remove quickly.
Step 4
Slide the Right side panel (B) into the groove of the face frame, and mount the male clip to
the face frame with the screwdriver. Each male clip will need 2 small screws (9).
Slide the Left side panel (C) into the Left groove of the face frame, and mount the male
clip to the face frame with a screwdriver. Each male clip will need 2 small screws (9).
Step 5
Slide bottom panel (D) into the groove of the right and left side panels, and then into the
groove in the frame below until it is fully seated.Slide in the back panel (E) and attach
the male clips to the back panel. There are three clips on the left side and three clips on
the right side. Each male clip will need 2 small screws (g).
Step 6
Use the long screws (i), to attach the back panel to the edges of the bottom panels.
Using the pre-drilled holes provided. Secure the toe kick (F) into the bottom of the
cabinet ,two small screws (g) in each of the two clips.
Step 7
Secure the support panel (G) under the bottom panel using a male
clips and two screws.
Step 8
Take the drawer glides from the carton and separate the exterior and interior glides into
left & right sets.
6 d /
7 —— =1 т ны аб, Lad P= = Za. =
©
ДИ © м © © © © © ем
00 /
a(L). =
A
©
©
©
©
©
o
O
Чо
я
b(L).
Step 9
Align the dovetails of one of the drawer side panels (H) with the teeth on the drawer
back panel (1) and gently seat the drawer side panel into the drawer back panel. This
can be done by gently tapping the side with a rubber mallet.
Repeat this procedure for the second drawer side panel.
Slide the drawer bottom into the grooves on the sides and drawer back panel until it
is fully seated.
И
A
a
Y UY “Y =X
Fo
A |
L
A
Step 10
Attach the drawer fronts (K) to the drawer box by aligning the dovetails of drawer panels
with the teeth on the front drawer panel (K) and gently seat as below.
>
Step 11
Attach the bottom drawer glides using three small flat head screws (h) on each side.
oO
Turn over the whole drawer box
NVAVAVAVAA
Step 12
Install the drawers into the cabinet by aligning the interior glides with the exterior glides in
the cabinet.
Using one small screw (g) attached the glide brackets to the interior sets of pre-drilled
holes on the back panel.
Optional holes: exterior two sets (a) are optional for soft-closing drawer glide.
= ©
Step 13
Using two small flat head screws (g) to attach both the left and right exterior drawer glides
(a) to the interior edge of the face frame left & right for each drawer.
Step 14
Install knobs (c). Pilot holes are provided on the back of the doors. If this is your desired
location, use a drill to complete drilling the holes through the door, then install the knobs
(с) with screws (k) provided.
Step 15
Use two middle size screws (h) to attach 4 wooden triangle blocks (d) in all four corners
of the top of the cabinet.
">