CF1247 TABLE
Please check contents before assembly. If any items are missing or damaged, do not take the unit back
to the store. Call 1-800-427-5136 for customer service and we will save you time by correcting any prob-
lems directly for you.
TABLE COMPONENTS
1 Leg Brace Plate
4 Preassembled
Leg Assemblies
| В
Fes —
A e
| NX
pea NT
2 Table Tops
Ze E Ne
O
TL /
SF E
o
\
NOTE: Cracks or Checks in logs are part of the natural
TOOLS AND HARDWARE
(Shown smaller than actual size)
16 - 2" Screws 14 - 1 3/4” Screws
@ Prmuenanmano = @ Drame
4-2 1/27 Screws
GRY.
fl 8 - 1/4” x 4” Hex Washer Head Screws
aati RRA
КОН
49
Phillips
7/16” or 3/8” Socket Screwdriver
or
beauty of cedar logs and should not be considered defects.
STEP 1 Lay the table tops upside down on a
clean flat surface. Slide them tight
together. Attach table top halves
together with fourteen 1 3/4” screws
in areas shown in figure |.
NOTE:
Read all instructions before starting.
4 SCREWS
-
a i]
=
€
|
< e 4 SCREWS
=> |
o A 5
TT
i
iH
figure 1
figure 2
STEP2 Place each leg assembly on top of the long cleats which =
run from the corner to the center of the table. Align the
leg assemblies flush with the center end of the cleats.
Attach with 4” Hex Washer Head Screws as shown in
figure 2.
STEP3 (Center the leg brace plate on top of the leg assemblies. figure 3
Attach with one 2 1/2” screw into each leg as shown
in figure 3.
STEP4 Atthe corners of the table attach two angle braces
to the outside legs. Place against the leg and angle |
until it is over the table cleats. Attach securely with
two 2” screws . Repeat for all the legs. As shown if
figure 4.
Your table 1s now assembled and ready for finish or immediate use.
If vou have hardware left over after completing your unit, it most
likely has been assembled mcorrectly, and may not be safe to use.
Please call Customer Service at 800-427-5136 for assistance.
>
Check all joints for tightness before and during each usage season.
Factory: 1 Lakeland Place. P.O. Box 350, Edmore, Michigan 48829, Phone: 800-427-5136 Fax: 989 -427-5824,
www. lakelandmlls.com
lakeland CF1130
CEDAR LOG DINING CHAIR
d
;
|
|
Ш
Ш
Please check contents before assembly. If any items are missing or damaged, do not take the unit back
to the store. Call 1-800-427-5136 for customer service and we will save you time by correcting any
problems directly for you.
LOG DINING COMPONENTS LOG CHAIR & LOVE SEAT HARDWARE
(Shown smaller than actual size)
Preassembled
Back 2 Back Legs 2 Front Legs
26" Long 26" Long
AN A =)
| у kJ a 9 id Fourteen Screws
Aal la -*j©| |O
Preassembled 5 Chair Arms
Seat
ыы
°C) o> 14 | 2 Le
| Braces
| o| |o FF
я \ ollo A
NOTE: Cracks or Checks in logs are part of the natural
beauty of cedar logs and should not be considered defects.
NOTE:
TOOLS REQUIRED
e Read all instructions before starting. Rubber Block of Wood #0
Mallet & Hammer Phillips
Screwdriver
e Do not completely tighten any screws until the
unit 1s fully assembled and setting on a level
surface.
e Use a rubber mallet (or a block of wood
between the hammer and the unit) to drive
doweled ends into holes as far as possible.
STEP 1 Lay assembled seat on floor. Insert dowel
end of uprights on assembled back into holes
on the back seat rail, adjust uprights in or
out as needed to align properly. Do not tap on seat
back with hammer.
To keep the seat rail from splitting, lay the back on
the floor and drive the seat onto the dowelled ends
by hitting on the bottom of the seat assembly.
figure 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Put ARMS onto legs by inserting dowel ends of
front and back legs into holes in arms. (NOTE:
Position of the hole on back leg is lower than hole
on front leg.) Drive arm onto leg assembly as far
as possible, stopping where taper begins. The
drilled holes on each Leg should face the same
direction as shown in figure 2.
Lay back and seat assembly on its side and
insert dowel ends of seat rail into holes on each leg.
Drive legs on as far as possible. Turn assembly over
and repeat procedure for the other side.
Set chair in upright position on a level surface and
when legs are in proper position, bring ARM in against
UPRIGHT. Tighten the preinstalled lag screws into the
pilot hole in the arm with a wrench or socket.
Secure doweled joints in place with screws perpendicular to
the doweled ends as shown in figure 4. Repeat procedure
for other side.
Tilt chair back and screw a brace on each side
of front legs to chair bottom.
Set unit on a level surface and tighten down all
lag screws firmly to secure unit. Secure all dowel
joints in place with screws perpendicular to the
doweled end as shown in figure 6.
Your chair is now assembled and ready for finish or
immediate use.
If vou have hardware left over after completing your unit, it most
likely has been assembled incorrectly, and may not be safe to use.
Please call Customer Service at 800-427-5136 for assistance,
Check all joints for tightness before and during each usage season.
5" HEX WASHER
HEAD SCREW
2" FLAT HEAD
SCREW
figure 4
figure 6
Factory: 1 Lakeland Place, P.O. Box 350, Edmore, Michigan 48829, Phone: 800-427-5136 Fax: 989 -427-5824,
www. lakelandmlls.com
">
