Rust-Oleum 320202 1 gal. Clear Concrete and Floor Topcoat Use and Care Manual

Rust-Oleum 320202 1 gal. Clear Concrete and Floor Topcoat Use and Care Manual
TECHNICAL DATA
ROC-108
CLEAR FINISH
FLOOR TOPCOAT
.DESCRIPTION AND USES
..PRODUCT APPLICATION (cont.)
.
®
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN YOUNG CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
Rust-Oleum Clear Finish Floor Topcoat is a ready-to-use
interior/exterior concrete clear protective formulated for use on
garages, carports, driveways, basements, porches, patios,
walkways and pool decks. This product is designed for use over
bare concrete or over one-part floor paints such as Rust-Oleum
Concrete & Garage Floor Paint + Primer to add a protective,
gloss finish that resists damage from hot tires, motor oil, grease
and gasoline. The durable, UV and weather resistant gloss finish
is easy to maintain and resists fading and peeling. It is
environmentally friendly and can be easily cleaned up with soap
and water. Not recommended for use on asphalt surfaces.
.PRODUCTS
SKU
320202
.
APPLICATION
.
Rust-Oleum Clear Finish Floor Topcoat is ready to use. Do not
thin. Apply only when air (ambient) temperature is between 5090ºF (10-32ºC) and the relative humidity is below 85%. Do not
paint outdoors if rain is expected within 48 hours. If using more
than one gallon, intermix (box) all cans of the same product to
ensure gloss uniformity. Stir thoroughly before applying. NOTE:
Painted floors may be slippery when wet. If desired, mix in
Rust-Oleum Anti-Skid Additive (sold separately).
Description
Clear Finish Floor Topcoat
.PRODUCT APPLICATION
.
READ ALL INSTRUCTIONS CAREFULLY BEORE
STARTING PROJECT
SURFACE PREPARATION
Whether over bare or previously coated concrete, proper
surface preparation is critical to performance. Allow new concrete
to cure for a minimum of 28 days. Before coating, if necessary,
use a wire brush or sander to remove any loose or unsound
concrete or masonry. Remove grease, oil, salt and other
contaminants with Rust-Oleum Heavy-Duty Degreaser or
Rust-Oleum Cleaner & Degreaser (sold separately). Scrub spots
thoroughly with a stiff bristle brush or broom and wipe up excess
cleaner with rags or paper towels to keep contaminates from
spreading. Rinse thoroughly with fresh water. Repeat as
necessary until completely clean.
Use a brush or edger to trim the perimeter and hard-to-reach
areas. Use a long handled extension pole and a high quality ⅜”
nap roller cover to apply an even coat of Rust-Oleum Finish
Floor Topcoat onto the surface. Apply in 4’x4’ foot sections and
maintain a wet edge to prevent lap marks and gloss differences.
Continue applying in 4’x4’ sections until complete. Only one coat
is necessary. If a second coat is desired, wait 4 hours before
applying the second coat in a direction perpendicular to the first.
Occasional touch-up may be necessary for areas subject to
heavy vehicle traffic.
Bare Concrete Surfaces: For proper penetration and
maximum adhesion, use Rust-Oleum Concrete Etch or
Rust-Oleum Clean & Etch (sold separately). Follow label
instructions carefully and allow the floor to dry completely. Wipe
your fingers over the clean, dry surface. If you see any dust or
powder on your fingers, repeat scrubbing and rinsing until the
floor is clean.
Dry and recoat times are based on 70ºF and 50% relative
humidity. Dry times increase at cooler temperatures. The surface
should be ready for light foot traffic in 24 hours. FOR FULL
CURE AND VEHICLE TRAFFIC, ALLOW 5 DAYS.
DRY & RECOAT TIMES
CLEAN-UP
Wash tools and equipment with warm water and a mild
detergent immediately after use. Properly dispose of all soiled
rags and protect unused product from freezing.
Previously Painted, Stained or Sealed Concrete Surfaces:
Use a wire brush to remove any loose or peeling paint, stain or
sealer. To ensure proper adhesion, scuff sand the entire surface
and clean with a solvent such as acetone.
COVERAGE
Each gallon contains enough material to cover approximately
150-250 square feet over bare concrete and 300-400 square feet
over coated concrete. Additional product may be required
depending on surface conditions.
1
Form: GDH-1354
Rev.: 051117
TECHNICAL DATA
CLEAR FINISH FLOOR TOPCOAT
PHYSICAL PROPERTIES
.
CLEAR FINISH FLOOR TOPCOAT
Resin Type
Acrylic
Pigment Type
NA
Solvents
Ethylene Glycol, Water
Per Gallon
8.6 lbs.
Per Liter
1.03 kg
By Weight
26.4%
By Volume
24.4%
Weight
Solids
Volatile Organic Compounds
<50 g/l (0.42 lbs./gal.)
Recommended Dry Film
Thickness (DFT) Per Coat
1.5-2.0 mils (37.5-50µ) per coat
Wet Film to Achieve DFT
(Unthinned Material)
6.0-8.0 mils (150-200µ) per coat
Practical Coverage at Recommended DFT
(assumes 15% material loss)
Dry Times at 70-80ºF
(21-27ºC) and 50%
Relative Humidity
Light Foot Traffic
Full Cure
Approximately 150-250 sq.ft. over bare concrete
Approximately 300-400 sq.ft. over coated concrete
3-4 hours
5 days
Shelf Life
3 years
Flash Point
>200°F (93°C)
Safety Information
For additional information, see SDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature
do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can
guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical
information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-1354
Rev.: 051117
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement