Teak Sealer™ TS-100 Surface Preparation: All surfaces must be dry, clean, sound and free of contaminants. Remove all dirt, grease, mildew, oil, dust, and other soluble contaminants. Remove all loose detrimental foreign matter by scraping, sanding or power sanding. Glossy surfaces should be lightly sanded. New Wood: Sand down to a smooth finish with fine sandpaper following the grain. Remove all sanding dust by vacuuming or dusting the surface with a “tack” cloth. Fill knot holes and cracks with putty filler for wood; let dry. Sand the filled areas smooth and remove dust. Previously Painted Surfaces: This coating is for application to unfinished wood surfaces or to surfaces previously finished with a similar finish in good conditions. Remove wax and oil using Lacquer Thinner. Sand smooth to dull glossy areas using a medium sandpaper (#120) and working your way to a thinner grade (#220). Always sand in the direction of the grain. Remove all dust. Severe chipping or peeling may require stripping to bare wood with paint strip, clean thoroughly and let it dry completely. Sand with fine sandpaper (#220) and remove all dust. If doubt exists concerning compatibility of this coating with the previous system, apply coating to a small area and allow to cure and age several weeks. Then inspect for adhesion failure, wrinkling, lifting or any other sign of incompatibility. If there are no signs, coating work can proceed. Mixing: This is a one component coating. Always hand mix thoroughly with a paddle before application. Do not mix excessively to avoid air in the coating. Do not shake. Method of Application: Apply by brush or roller, use All Purpose Roller 3/8” or conventional or airless spray. Roller application may require special care to prevent bubbling and more than one coat to obtain proper thickness. Apply at 4 mils wet film thickness that will yield 2 mils dry film thickness. With a clean soft varnish brush apply a thin, smooth coat brushing in grain direction. Maintain a wet edge and brush out any lap marks. A second coat, if desired, may be applied without sanding as soon as first coat is dry. If allowed to dry more than 12 hours, sand or buff with fine sandpaper (#220) or steel wood to insure proper adhesion between coats. Remove all dust before varnishing. Airless Spray: Minimum of 28:1 ratio pump, 0.011”-0.013” orifice tip 1/4” ID Teflon material hose. Limitation: Apply in good weather when air and surface temperature are above 40ºF and surface temperature is at least 5ºF above the dew point. For optimum application properties, material should be between 70º to 100ºF prior to mixing and application. Note: When multiple coats of product are applied, be sure to sand lightly between coats with a fine sandpaper and dust clean or vacuum. Cleanup: Wipe up drips and spatters with Lanco® Mineral Spirits MS-107. Clean all equipment with this solution. Caution: Do not take internally. Close container after each use. Keep out of the reach of children. Combustible; keep away from heat and open flame. Avoid prolonged contact with skin and breathing vapors or spray mist. DANGER / WARNING: PRECAUTION: FLAMMABLE MIXTURE, DO NOT USE NEAR FIRE OR FLAME. CONTAINS: PETROLEUM DISTILLATES. USE ONLY WITH ADEQUATE VENTILATION. AVOID PROLONGED OR REPEATED BREATHING OF VAPOR. It is important to use adequate ventilation as high vapor concentration may cause unconsciousness or even asphyxiation. Ventilation must be sufficient to limit exposure below MSDS limits. Eye irritation and dizziness are indications of over exposure. Refer to LANCO MATERIAL SAFETY DATA SHEET. PROVIDE ADEQUATE VENTILATION DURING APPLICATION AND DRYING CYCLES. DO NOT TAKE INTERNALLY. Swallowing may cause injury, illness or death. If swallowed, do not induce vomiting. Call a physician immediately. NOTICE: Reports have associated repeated and prolonged occupational over exposure to solvents, with permanent brain and nervous system damage, peripheral nervous tissue damage and liver abnormalities. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. ALWAYS WEAR RESPIRATORY PROTECTION (NIOSH, MSHA TC 23C OR EQUIVALENT). KEEP OUT OF REACH OF CHILDREN.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021