Whirlpool WFE775H0HW 6.4 cu. ft. Electric Range in White with Frozen Bake Technology Instructions / Assembly

Whirlpool WFE775H0HW 6.4 cu. ft. Electric Range in White with Frozen Bake Technology Instructions / Assembly
Product Dimensions
NOTE: The model may look different than the one pictured.
A. 273/8" (69.5 cm) max. depth with handle
B. 461/2" (118.1 cm) overall height (max.) with leveling legs
screwed all the way in*
C. 36" (91.4 cm) cooktop height (max.) with leveling legs screwed
all the way in*
D. 297⁄8" (75.9 cm) width
E. 255⁄16" (64.3 cm) depth - back of range to front of cooktop**
F. Model/serial rating plate (located on the frame behind a top
corner of the door or either side of the drawer)
IMPORTANT: Range must be level after installation. Follow the instructions in the “Level Range” section. Using the cooktop as
a reference for leveling the range is not recommended.
*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.
**Front of door and drawer may extend further forward depending on styling.
Cabinet Dimensions
Electrical Requirements — U.S.A. Only
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
A freestanding range may be installed next to combustible walls
with zero clearance.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or service technician if you are in doubt as to
whether the appliance is properly grounded. Do not modify the
power supply cord plug. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial rating plate.
The model/serial rating plate is located on the frame behind
a top corner of the door or either side of the drawer. Refer
to the figures in “Product Dimensions” in the “Location
Requirements” section.
This range is manufactured with the neutral terminal
connected to the cabinet. Use a 3-wire, UL Listed, 40- or
50-amp power supply cord (pigtail) (see the following Range
Rating chart). If local codes do not permit ground through
the neutral, use a 4-wire power supply cord rated at
250 V, 40 or 50 amps and investigated for use with ranges.
13" (33.0 cm) max. upper cabinet depth
30" (76.2 cm) min. opening width
For minimum clearance to top of cooktop, see NOTE*
30¹⁄8" (76.5 cm) min. opening width
Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,
5¹⁄2" (14.0 cm) max. from floor
F. Cabinet door or hinges should not extend into the cutout
* NOTE: 24" (61.0 cm) minimum when bottom of wood or
metal cabinet is covered by not less than 1/4" (6.4 mm) flame
retardant millboard covered with not less than No. 28 MSG
sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the
cooking platform and the bottom of an uncovered wood or
metal cabinet.
Range Rating*
Specified Rating
of Power Supply
Cord Kit and Circuit
120/240 Volts
120/208 Volts
8.8-16.5 KW
7.8 - 12.5 KW
40 or 50**
16.6-22.5 KW
12.6 - 18.5 KW
* The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
** If connecting to a 50-amp circuit, use a 50-amp rated cord
with kit. For 50-amp rated cord kits, use kits that specify use
with a nominal 1³⁄8" (34.9 mm) diameter connection opening.
A circuit breaker is recommended.
The range can be connected directly to the circuit breaker
box (or fused disconnect) through flexible or nonmetallic
sheathed, copper, or aluminum cable. See the “Electrical
Connection — U.S.A. Only” section.
Allow 2 to 3 ft (61.0 to 91.4 cm) of slack in the line so that the
range can be moved if servicing is ever necessary.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF