Form No. 3357-927 Rev B

Hour Meter Kit for Zero-Turn-Radius Riding Mower

Model No. 112-9763

Installation Instructions

Note: Determine the left and right sides of the machine from the normal operating position.

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

2

3

4

Description

Hour meter

Mounting clip (some kits only)

Self tapping screws

Hour meter wiring harness

Qty.

1

1

2

1

Use

Assemble the hour meter.

Install the hour meter.

Connect the hour meter.

1

Preparing the Machine

No Parts Required

Procedure

1. Park the machine on a level surface and disengage the blade control switch.

2. Move the motion control levers outward to the park position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Lift the seat forward and lower it to the floor board to access the battery, frame and wiring harness.

4. Locate the battery and negative terminal.

Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

• Always

disconnect

the negative (black) battery cable before disconnecting the positive (red) cable.

• Always

connect

the positive (red) battery cable before connecting the negative (black) cable.

2

Assembling the Hour Meter

Parts needed for this procedure:

1

1

Hour meter

Mounting clip (some kits only)

Servicing a machine with a live electrical system can result in electric shock.

Always

disconnect

the negative (black) battery cable before performing any service on the machine.

5. Disconnect the negative (black) ground cable from the battery post. Retain all fasteners.

Procedure

Locate and inspect the hourmeter in loose parts.

Printed in the USA.

Original Instructions (EN) All Rights Reserved

• For hourmeters with a separate mounting clip:

Install the hour meter to the bracket with a mounting

clip as shown in Figure 1

1

2

4

1

2

3

3

G005542

Figure 1

3.

Mounting clip 1.

Hour meter

2.

Bracket

• For hourmeters with integrated mounting clips:

Install the hour meter to the bracket as shown in

Figure 2.

1

2

1.

Hour meter

G015643

Figure 2

2.

Bracket

3

Installing the Hour Meter

Parts needed for this procedure:

2 Self tapping screws

Procedure

1. Locate the two holes in the frame support shown

in Figure 3. Install the hour meter assembly to the

location as shown.

1.

Self tapping screw

2.

Hour meter

G005302

Figure 3

3.

Holes in frame

4.

2. Use the self tapping screws to install the bracket onto

the seat support in the orientation shown in Figure 3.

4

Connecting the Hour Meter

Parts needed for this procedure:

1 Hour meter wiring harness

Procedure

1. Locate the hour meter wiring harness in loose parts.

2. Locate the female box connector at the end of the wiring harness. It has two offset slots to mate with the hour meter.

3. Install the positive female box connector to the male plugs on the underside of the hour meter as shown

in Figure 4.

2

1

6

5

1

2

7

3

2

4

G005544

1.

Hour meter

2.

Female box connector

3.

Positive male plug

Figure 4

4.

Ring connector to negative battery terminal, wiring harness

5.

Single female terminal, wiring harness

6.

Enclosed male terminal, wiring harness

7.

Negative male plug, hour meter

8.

Negative connector (black)

4. Locate the single female and the enclosed male terminals at the opposite end of the wiring harness

(Figure 4).

5. Route these terminals to the under side of the control

panel and locate the ignition switch base (Figure 5).

Note: Depending on the machine, it may be necessary to remove the four screws securing the control panel to the console to access the ignition switch base.

1.

Ignition switch base

3

G005545

Figure 5

3.

Single wire and outer terminal

2.

Wiring harness

6. Remove the single wire from the outer terminal at

the base of the ignition switch (Figure 5).

3

7. Install the single female terminal at the end of the hour meter wiring harness to the open terminal on

the base of the ignition switch (Figure 6).

3

4

7

5

1

2

G005546

6

Figure 6

1.

Hour meter wiring harness 5.

Single wire removed previously

2.

Wiring harness

3.

Enclosed male terminal, wiring harness

6.

Open terminal, ignition switch

7.

Ignition switch base

4.

Single female terminal, wiring harness

8. Install the single wire from the wiring harness removed previously to the enclosed male terminal on the hour meter wiring harness to complete the

circuit (Figure 6).

9. Route the remaining ring terminal on the hour meter harness to the negative battery post. Secure the hour meter ring terminal and negative battery cable to the negative terminal using the existing fasteners.

10. Verify the display has power by turning the ignition key to run. The hour meter will run when the ignition key is in the Run position. An hourglass symbol flashes on the meter display when it is running.

4