CP12047
Pivoting
Shower Door Kit
INSTALLATION GUIDE
Consult your local plumbing codes prior to installation.
For easy installation of your unit you will need to:
• READ ALL the instructions completely before beginning.
• READ ALL warnings, care, and maintenance information.
• Purchase the correct water supply components.
Distributed by:
Liberty Hardware Manufacturing Corporation
140 Business Park Drive
Winston-Salem, NC 27107
©2016 LHMC, A Masco Company
Made in China
For More Information Call: 1.800.964.4850
1 MAR 2016
BEFORE YOU START
CAUTION: Risk of injury. DO NOT attempt to cut tempered glass.
CAUTION: Use work gloves to protect against sharp edges and corners.
CAUTION: DO NOT set the glass panel on concrete or other hard surface.
CAUTION: Open toe shoes like sandals or flip flops should not be worn when installing tub or shower doors.
NOTE:
• Shower opening dimensions: Due to variability of enclosures and wall construction, exact width dimensions may vary.
– 32" Pivot door: 30-1/8" minimum to 32-1/8" maximum.
– 34" Pivot door: 32-1/8" mimimum to 34-1/8" maximum.
• Walls must be within 3/8" (10 mm) of plumb.
• Cover tub or shower drain with rag or tape to avoid loss of small parts.
• Follow the silicone sealant manufacturer's instructions for application and curing time.
CARE AND CLEANING
For regular cleaning use ONLY mild detergents or warm, soapy water. Use ONLY non-abrasive cloth or sponge. ALWAYS rinse surfaces after cleaning.
Before cleaning this product with cleaning products, test a small, inconspicuous area.
CAUTION: Manufacturer does not recommend the use of cleaning products that contain any of the following chemicals. Use of products containing these chemicals can cause the products to crack or discolor and will void the warranty.
• Naphtha
• Hydrogen Peroxide Solution (common household peroxide)
• Toluene
• Ethyl Acetate
• Lye (common in drain cleaner)
• Acetone
For further inquiries, contact customer service at 1-800-964-4850.
THREE YEAR LIMITED WARRANTY
Liberty Hardware plumbing products are warranted to be free of defects in material and workmanship for three years from date of purchase.
Liberty Hardware will, at its election, repair, replace or make appropriate adjustment where Liberty Hardware determines that such defect occurred during normal usage within three (3) years after purchase. Liberty Hardware is not responsible for removal, installation costs, or incidental or consequential losses. Labor charges and/or damage incurred in installation, repair, or replacement of the product, as well as any other kind of loss or damage, are excluded. This warranty is not transferable. This warranty does not cover damage or defects relating to misuse, abuse, negligence, normal wear and tear, accident, acts of God, repairs or alterations not authorized by Liberty Hardware, or improper installation, storage or handling.
To obtain warranty service, contact Liberty Hardware either through your Dealer, Plumbing Contractor, Home Center, or by writing Liberty
Hardware Attn.: Customer Solutions, 140 Business Park Drive, Winston-Salem, NC 27107, USA, or by calling 1-800-964-4850 from within the USA. Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Liberty Hardware for all warranty claims.
DISCLAIMER:
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED
IN DURATION TO THE DURATION OF THIS WARRANTY.
LIBERTY HARDWARE AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state/province to state/province.
2
23
19
20
18
19
20 9
18
19
3
18
4
20
25
5
23
6
13
17
10
22
22
Illustrated Parts Breakdown
(For shower head nozzle on left)
24
16
15 24
24
2
18
7
18
19
1
11
19
6
15
16
17
14
12
18 19
N O . Q TY P ART D ESCRIPTION
#1 1 Adjustable Pivot Jamb
#2 2 Adjustable Pivot Jamb Bracket
#3 1 Slip Jamb Male
#4 1 Slip Jamb Female with Magnetic Jamb Seal
#5 1 Pivot Strike Rail
#6 2 Door Top/Bottom Rail
#7 1 Door Side Rail
#8 1 Dam Strip
#9 1 Handle Outside
#10 1 Handle Inside (with Holes)
#11 1 Plastic Water Diverter and Gasket
#13 1 Pivot Bushing (Top)
#14 1 Pivot Bushing (Bottom)
#15 2 Pivot Pin
#16 2 Spanner Washer
#17 2 Kep Nut
#18 6 #8 x 1 1/2″ PH SMS Screw
#19 6 Screw Anchor
#20 3 #6 x 3/8 ʺ “B”-Point Screw
8
24
24
2
24
N
O
. Q
TY P ART
D
ESCRIPTION
#22 2 #6 x 1-1/2” Flat Head Tapping Screw
#23 2 Magnetic Jamb Seal
#24 6 #8 x 1/2 ʺ FH SMS Screw
3
In this instruction booklet we will walk you through the installation of your new shower door.
DO NOT REMOVE your old shower door until you check your new shower door kit for all the proper parts. Make sure that you have all the proper tools required to assemble your new shower door.
Use this check list.
• Phillips Screwdriver
• Level
• Electric Drill
• 1/8” Drill Bit (for fiberglass stall)
• 3/16” Masonry Drill Bit (for tile stall)
• 7/64” Drill Bit
• 7/16” Open End Wrench
• Pliers
• Pencil
• Hammer
• Tin Snips
• Caulking Gun and one Tube of Clear Silicone
• Tape Measure
• Safety Glasses
CAUTION: Wear safety glasses whenever drilling or cutting. Handle the Door panel carefully. The corners of the panel can damage tile and floor covering.
Tempered glass cannot be cut.
STEP 1 Checking Contents of
Shower Door Package
DO NOT use a razor blade to cut open the paper wrapping as you may scratch the contents. Use the IPB Drawing to help you locate the following parts:
No. Qty. Description
(#1) 1 Adjustable Pivot Jamb
(#2) 2 Adjustable Pivot Jamb Bracket
(#3) 1 Slip Jamb Male
(#4) 1 Slip Jamb Female with
Magnetic Jamb Seal
(#8) 1 Dam Strip
(#9) 1 Handle Outside
(#10) 1 Handle Inside (with Holes)
(#11) 1 Plastic Water Diverter & Gasket
(#13) 1 Pivot Bushing (Top)
(#14) 1 Pivot Bushing (Bottom)
(#15) 2 Pivot Pin
(#16) 2 Spanner Washer
(#17) 2 Kep Nut
(#18) 6 #8 x 1 1/2” PH SMS Screw
(#19) 6 Screw Anchor
(#20) 3 #6 x 3/8” “B”-Point Screws
(#22) 2 #6 x 1-1/2” Flat Head Tapping Screw
(#24) 6 #8 x 1/2” FH SMS Screw
If you find that any parts are damaged or missing, refer to the parts list and IPB Drawing and contact
Liberty Hardware's Customer Service Department at
1-800-345-3358. NOTE: Views and directions given in these instructions – left, right, front, back, etc. – are from outside the enclosure, facing the shower.
STEP 2 Removing the Existing
Enclosure
A. Remove existing shower door and all existing parts to that door assembly. Remove all screw anchors from the wall. Remove silicone sealant or tub caulking and any other contaminants from shower.
STEP 3 Installing the
Adjustable Pivot Jamb
NOTE: The wall opposite the shower head and controls
will be the pivot side. Some situations may require
the door to pivot on the same side as the shower
head and controls.
A. Using the Tape Measure, find the center of the shower dam. Make a mark where the center is on both ends of the dam. (See Figure 1).
Dam Centerline
Dam Centerline Figure 1
4
B.
Pivot Jamb (#1), the
Adjustable Pivot Jamb
Brackets (#2) and six
#8 x 1/2” FH SMS
Screws (#24).
Adjustable
Pivot Jamb Bracket
C. Secure the Adjustable
Pivot Jamb Brackets
(#2) to the Adjustable
Pivot Jamb (#1) with the
#8 x 1/2” FH SMS Screws
(#24). Tighten the bottom three screws completely. Tighten the top three screws only half way.
D. Locate the Pivot Bushing (Bottom) (#14) and press it into the Bottom
Adjustable Pivot Jamb
Bracket (#2) plate hole
(See Figure 2).
Adjustable
Pivot Jamb
Bracket
Pivot
Bushing
(Bottom)
Figure 2
E. Align the center of the Pivot Bushing (Bottom)
(#14) with the mark on the shower dam. Use a
Level against the Adjustable Pivot Jamb (#1) to align it straight up and down (See Figure 3). Using a Pencil, mark the wall through each of the three pre-drilled holes in the side of the Adjustable
Pivot Jamb (#1). Remove the Adjustable Pivot
Jamb (#1).
Level the Slip
Jamb Male
Level the Adjustable Pivot Jamb
Figure 3
C. Using either a 1/8” Drill Bit (for a fiberglass enclosure) or a 3/16” Masonry Drill Bit (for tile/ marble) drill holes where you made the pencil marks. If installing in a tile/marble enclosure, gently tap a Screw Anchor (#19) into each hole. DO NOT use the Screw Anchors (#19) for a fiberglass enclosure.
D. Position the Slip Jamb Male (#3) and use three
#8 x 1 1/2” PH SMS Screws (#18) to secure the
Slip Jamb Male (#3) to the wall.
F. Using either a 1/8” Drill Bit (for a fiberglass enclosure) or a 3/16” Masonry Drill Bit (for tile/marble), drill holes where you made the marks.
If installing in a tile/marble enclosure, gently tap a Screw Anchor (#19) into each hole.
DO NOT use the Screw Anchors for a fiberglass enclosure .
STEP 5 Installing the Slip
Jamb Female
A. Locate the Slip Jamb Female (#4) (comes with
Magnetic Jamb Seal (#23) pre-installed) and three
#6 x 3/8” “B”-Point Screws (#20).
G. Position the Adjustable Pivot Jamb (#1) and use three #8 x 2 1/2” PH SMS Screws (#18) to secure the Adjustable Pivot Jamb (#1) to the wall.
STEP 4 Installing the Slip
Jamb Male
A. Locate the Slip Jamb Male (#3) and three
#8 x 1 1/2” PH SMS Screws (#18).
B. Place the Slip Jamb
Female (#4) over the
Slip Jamb Male (#3) with the Magnetic Jamb
Seal (#23) facing OUT towards you as you look into the shower. Use the
Level to adjust the Slip
Jamb Female (#4) ver-
, towards you as you look into the shower. Use the
Level to adjust the Slip
Jamb Female (#4) vertically. DO NOT secure at this time.
OUT ,
B. Place the Slip Jamb Male (#3) at the centerline mark on the shower dam opposite the Adjustable
Pivot Jamb (#1) as shown in Figure 3. Use the
Level to align the Slip Jamb Male (#3) straight up and down. Use the pencil tip in each of the predrilled holes in the Slip Jamb Male (#3) to mark the wall. Set the Slip Jamb Male (#3) aside.
Figure 4
5
STEP 6 Installing the Pivot Pin
Assemblies
A. Locate the Pivot
Pins (#15), Spanner Washers (#16),
Kep Nuts (#17) and Pivot Bushing
(Top) (#13).
13
17
16
15 tighten the Kep Nuts (#17) at the top and bottom of the door, maintaining the 1/8” gap.
D. Standing inside the shower, use the 7/64” Drill
Bit to drill holes through the Slip Jamb Female pre-drilled holes and into the Slip Jamb Male.
Secure the Slip Jamb Female (#4) to the Slip
Jamb Male (#3) with three #6 x 3/8”
“B”-Point Screws (#20) (See Figure 4 on page five).
B. Loosely assemble the two Pivot
Assemblies: Pivot
Pin (#15), Spanner
Washer (#16) and
Kep Nut (#17).
Place the square head of a Pivot Pin
15
(#15) into each pivot slot of the
Door Top and
Bottom Rails (#6)
16
17
Figure 4 on the door panel.
Slide the Pivot Pin (#15) toward the narrow end of the pivot slot in the Door Top and Bottom Rails
(#6) and hand tighten.
Note: Once installed, if you find that the door will not stay closed, the magnet needs to be turned around. Remove the Magnetic Jamb Seal (#23) and reinsert it the other way.
STEP 8 Installing the Plastic Water
Diverter and Gasket
STEP 7 Installing the Door
NOTE: Installing the door may be slightly easier with another person to assist you.
A. Carefully lift the door and set the bottom Pivot
Pin (#15) into the Pivot Bushing (Bottom) (#14).
Holding the door panel in place, set the Pivot
Bushing (Top) (#13) over the top Pivot Pin (#15)
(See Figure 5).
B. Lift the top Adjustable
Pivot Jamb Bracket
(#2) and align the top
Pivot Pin (#15) and
Pivot Bushing (Top)
(#13) with the hole in the top Adjustable
Pivot Jamb Bracket
(#2). Lower the Adjustable Pivot Jamb Bracket (#2) onto the Pivot
Pin (#15) and Pivot
Bushing (Top) (#13) and tighten the three top screws.
Top
Pivot
Bushing
Door
Panel
Pivot Jamb
Bracket
C. Close the door and adjust it so that there
Figure 5
Pivot Jamb
Bracket is a 1/8” gap along the entire length of the door on the strike side. Use the 7/16” wrench to
B.
A.
Locate the plastic water diverter and gasket (#11).
Measure the bottom of the Door Panel. Reduce this measurement by 1- 1/4" and carefully cut with tin snips or large scissors. This will allow the door to close against the Slip Jamb and the magnetic seal (#4).
Carefully slide the water diverter and gasket onto the bottom of the door panel. See Fig. 6
Water Diverter and Gasket
Figure 6
Inside Shower
6
STEP 9 Installing the Handles
A. Locate the Handle Outside (#9), Handle Inside
(with Holes) (#10).
B. Use the #6 x 1-1/2 " Flat Head Tapping Screws to attach the Handles to the Pivot Strike Rail
(#5). Screw heads should be inside the shower.
STEP 10 Installing the Dam Strip
STEP 11 Silicone Sealing the
Enclosure
A. Using clear Silicone, seal all edges, both interior and exterior where the Adjustable Pivot Jamb (#1),
Adjustable Pivot Brackets (#2), Slip Jamb Female
(#4) and Dam Strip (#8) meet and where they meet the tile or fiberglass.
NOTE: Silicone sealant must cure for 24 hours before you use your new enclosure. Silicones may vary. Please follow manufacturer's instructions for safety, cleaning and disposal recommendations.
A. Locate the Dam Strip (#8). Notice that one end has been pre-cut to fit the shape of the Adjustable
Pivot Jamb Bracket (#2).
B. From the outside of the shower enclosure insert the Dam Strip (#8) to meet the Adjustable Pivot
Jamb Bracket (#2). Cut the other end of the Dam
Strip (#8) straight to fit up against the Slip Jamb
Female (#4) (See Figure 7).
Straight cut
Notched end abuts
Jamb Bracket
Dam Strip
Outside Shower
Figure 7
C.
Make sure that the top surface of the shower dam is completely clean of oil, dust, debris or other contaminants. Apply a small 1/4" to 3/8" bead of 100% silicone to the underside of the
Dam Strip (#8). Wipe away excess silicone immediately. Follow sealant manufacturer for proper use and clean-up recommendations.
7
8
