Rust-Oleum 301239 User manual

Rust-Oleum 301239 User manual
TECHNICAL DATA
ROC-113
RUST-OLEUM®
MOISTURE STOP
.DESCRIPTION AND USES
.
.PRODUCT APPLICATION (cont.)
®
APPLICATION
Rust-Oleum Moisture Stop penetrates into concrete and
reacts with the free calcium and water to form a gel in
cracks, pores and capillaries to protect against the ingress
of water and contaminants. This allows surfaces that were
previously uncoatable, due to moisture, to be coated.
Moisture Stop is ready to use. Do not thin. Use only when
air (ambient) temperature is between 50-90°F (10-32°C)
and the relative humidity is below 85%. Shake the
container vigorously for 30-45 seconds. Completely
saturate the surface at 150-200 square feet per gallon,
using a low-pressure sprayer or by pouring the product
directly on the floor. Move the product around on the floor
with a stiff bristle broom or squeegee to work the product
into the floor. Using a hose or sprayer, mist the surface
with water to keep the floor wet for 30-45 minutes. After 45
minutes, squeegee or broom the excess moisture from the
surface.
Moisture Stop is suitable for use on bare concrete and
masonry surfaces, such as garage floors, driveways,
sidewalks, stairs, patios, pool decks, basements, retaining
walls and cinder block walls. It can be used as a curing
agent on newly poured concrete within 28 days. Do not
use on asphalt.
.PRODUCT
SKU
301239
.
Container Size
1-Gallon Moisture Stop
. PRODUCT FEATURES




IMPORTANT: Wait a minimum of 2 hours, then flush the
surface with water and squeegee to a surface dry
condition. Failure to flush the surface will result in the
appearance of efflorescence and will require the use of
Rust-Oleum Efflorescence Remover (sold separately).
.
Prevents moisture from coming through concrete floors
For use on concrete prior to coating
Strengthens & seals from the inside out
For interior and exterior use
PRODUCT APPLICATION
.
COVERAGE
On new concrete, each gallon will cover 200 square feet
per gallon. On old concrete, each gallon will cover up to
150 square feet per gallon. Areas with crazing (fine cracks
on the surface) may take two applications.
.
TESTING CONCRETE FOR MOISTURE
Apply a 2’x2’ sheet of plastic to the garage floor. Tape
down the edges with duct tape and let set for 24 hours. If
water droplets form on the inside of the plastic or concrete
appears wet (darker in color), moisture is trapped in the
floor and Rust-Oleum Moisture Stop should be used prior
to coating.
DRY TIME
Dry time is based on 70°F and 50% relative humidity. After
flushing the surface, the concrete floor is ready for foot
traffic after 2 hours and vehicle traffic after 12 hours. Allow
24 hours before staining, sealing or coating.
CLEAN-UP
SURFACE PREPARATION
Wash tools and equipment with soap and warm water.
Properly dispose of all soiled rags and protect unused
product from freezing.
Proper surface preparation is critical to achieve best
results. Remove any oil or grease with Rust-Oleum
Cleaner & Degreaser (sold separately). Scrub spots
thoroughly with a stiff bristle brush or broom. Rinse
thoroughly with fresh water, preferable with a power
washer. Repeat as necessary to completely clean and
rinse. Allow to thoroughly dry. If the floor will be coated,
use Rust-Oleum Clean & Etch and follow with Rust-Oleum
Moisture Stop.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO
NOT TAKE INTERNALLY.
1
Form: GDH-1359
Rev.: 052517
TECHNICAL DATA
RUST-OLEUM® MOISTURE STOP
.PHYSICAL PROPERTIES
.
Composition
Modified Silicate
Solvent
Weight
Water
Per Gallon
9.14 lbs.
Per Liter
1.02 kg
Volatile Organic Compounds
0 g/l
New Concrete – 200 sq.ft./gal.
Old Concrete – 150 sq.ft./gal.
Practical Coverage
Dry Times @ 70-80º F
(21-27°C) and 50%
Relative Humidity
Touch
1 hour
Foot Traffic
2 hours
Vehicle Traffic
12 hours
Shelf Life
2 years
Flash Point
>200°F (93°C)
Safety Information
For additional information, see SDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-1359
Rev.: 052517
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement