NuTone AN110 Installation guide

NuTone AN110 Installation guide
SERIES FAN
ALL INSTALLATIONS
Start here.
COOKING AREA
Do not install above or
inside this area.
Please visit our website - www.broan.com, www.broan.ca,
www.nutone.com, or www.nutone.ca - to register this
product and to view installation tips and videos.
45o
READ AND SAVE THESE INSTRUCTIONS
WARNING
NOT FOR USE IN
A COOKING AREA.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Acceptable for use over a tub or shower when connected to a
GFCI (Ground Fault Circuit Interrupter) - protected branch circuit
(ceiling installation only).
8. This unit must be grounded.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. Attach damper/duct connector to
fan housing.
45o
Push connector through
opening from inside of
housing.
Cooking
Equipment
Floor
IMPORTANT - The ducting from this fan to the outside of the
building has a strong effect on the air flow, noise and energy use
of the fan. Use the shortest, straightest duct routing possible for
best performance, and avoid installing the fan with smaller ducts
than recommended. Insulation around the ducts can reduce
energy loss and inhibit mold growth. Fans installed with existing
ducts may not achieve their rated airflow.
ROOF CAP* (with built-in damper)
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code
authorities.
NEW CONSTRUCTION
For Retrofit Installation - Skip to back page.
FAN
HOUSING
POWER
CABLE *
Keep duct
runs short.
Seal gaps
around
housing.
* Purchase separately.
4-IN. ROUND
ELBOWS*
1. Remove blower and all packing material
from fan housing.
CLEANING & MAINTENANCE
Use an on/off switch or speed control to operate this ventilator.
See “Connect Wiring” for details.
Installer: Leave this manual with the homeowner.
If mounting housing to I-joist,
use wood blocking as shown.
6. Connect wiring.
Bend tab to expose desired
access hole. Connect
power cable to housing with
appropriate UL approved
connector. Connect black
to black, white to white and
green to green or bare wire.
Re-install wiring panel and
secure with screw from parts
bag.
4. Please read specification label on product for further information
and requirements.
OPERATION
Secure housing through
mounting ears with
appropriate fasteners.
OPTION - To mount housing anywhere between ceiling framing:
Use optional Hanger Bar Kit (sold separately from local distributors or
website). Follow mounting instructions included with kit.
3. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
The motor is permanently lubricated and never needs oiling. If
the motor bearings are making excessive or unusual noises,
replace the blower assembly (includes motor and impeller).
Make sure bottom of housing
will be flush with finished ceiling.
WALL CAP*
(with built-in
damper)
2. This product can be installed in a wall if mounted 8-ft. or more
above the floor.
For quiet and efficient operation, long life, and attractive
appearance - lower or remove grille and vacuum interior of unit
with the dusting brush attachment.
4. Mount housing to ceiling structure.
5. Connect 4-in. round duct.
OR
Seal duct joints
with tape.
TABS
For proper location using ½”
ceiling material: Bend out
housing tabs to fit against
bottom of structure.
INSULATION
(Place around and
over fan housing.)
4-IN. ROUND
DUCT*
Engage tabs and secure
with screw from parts bag.
2. Remove wiring panel from fan housing.
HOUSING
TABS
7. Install blower.
5. Connect wiring.
Re-install blower removed in Step 2. Secure blower with 2 screws
from parts bag and plug blower into black receptacle.
Limited Warranty
Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the
original consumer purchaser of its product (“you”) that the product (the “Product”) will be
free from material defects in the Product or its workmanship for a period of one (1) year from
the date of original purchase.
Bend tab to expose desired
access hole. Connect power
cable to housing with appropriate
UL approved connector. Connect
black to black, white to white and
green to green or bare wire. Reinstall wiring panel and secure
with screw from parts bag.
The limited warranty period for any replacement parts provided by the Company and for
any Products repaired or replaced under this limited warranty shall be the remainder of the
original warranty period.
This warranty does not cover speed controls, fluorescent lamp starters, tubes, halogen
and incandescent bulbs, fuses, filters, ducts, roof caps, wall caps and other accessories
for ducting that may be purchased separately and installed with the Product. This warranty
also does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any
Products or parts which have been subject to misuse, abuse, abnormal usage, negligence,
accident, improper or insufficient maintenance, storage or repair (other than repair by
the Company), (d) damage caused by faulty installation, or installation or use contrary to
recommendations or instructions, (e) any Product that has been moved from its original
point of installation, (f) damage caused by environmental or natural elements, (g) damage
in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, or
(j) damage caused by fire, flood or other act of God. This warranty covers only Products sold
to original consumers in the United States by the Company or U.S. distributors authorized
by the Company.
8. Finish ceiling, then install grille.
Squeeze grille springs and insert into slots in housing. Push
grille up against ceiling.
This warranty supersedes all prior warranties and is not transferable from the original
consumer purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and
your sole remedy for defective products. The foregoing warranties are exclusive and in lieu
of any other warranties, express or implied. THE COMPANY DISCLAIMS AND EXCLUDES
ALL OTHER EXPRESS WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES
IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law prohibits the
exclusion of implied warranties, the duration of any applicable implied warranty is limited to
the period specified for the express warranty above. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you. Any oral
or written description of the Product is for the sole purpose of identifying it and shall not be
construed as an express warranty.
6. Mount fan to ceiling structure.
Mount housing to ceiling
structure with standard
drywall or wood screws in
locations shown. *Center
hole optional.
*
Whenever possible, each provision of this Limited Warranty shall be interpreted in such
manner as to be effective and valid under applicable law, but if any provision is held to be
prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition
or invalidity, without invalidating the remainder of such provision or the other remaining
provisions of the Limited Warranty.
RETROFIT
3. Remove old fan.
Enlarge ceiling opening (if necessary) to 9¾” parallel to joist) by
10½” (perpendicular to joist). Leave ductwork and wiring in place.
7. Connect 4-in. round duct.
Pull existing ducting through housing discharge opening and tape
ducting to duct connector. Push connector/ducting back through
opening. Engage tabs and secure with screw from parts bag.
3
TABS
2
1
1
2
Install blower. Finish ceiling, then install grille.
See Steps 7 & 8 at top of this page..
RECEPTACLE
BLACK
SWITCH BOX
This warranty covers only replacement or repair of defective Products or parts thereof at
the Company’s main facility and does not include the cost of field service travel and living
expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations
or exclusions of this limited warranty will not constitute a waiver of such terms, limitations or
exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or
replacing any defective Product, except for those incurred with the Company’s prior written
permission.
WIRING DIAGRAM
ON / OFF SWITCH
(purchase separately)
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT
PARTS, OR REPAIR OR REPLACE, AT THE COMPANY’S OPTION, SHALL BE YOUR SOLE
AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S SOLE
AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL,
INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION
WITH THE PRODUCT, ITS USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state to state.
4
4. Fold mounting ears flat against housing.
Remedy: During the applicable limited warranty period, the Company will, at its option,
provide replacement parts for, or repair or replace, without charge, any Product or part
thereof, to the extent the Company finds it to be covered by and in breach of this limited
warranty under normal use and service. The Company will ship the repaired or replaced
Product or replacement parts to you at no charge. You are responsible for all costs for
removal, reinstallation and shipping, insurance or other freight charges incurred in the
shipment of the Product or part to the Company. If you must send the Product or part to the
Company, as instructed by the Company, you must properly pack the Product or part—the
Company is not responsible for damage in transit. The Company reserves the right to utilize
reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty
repair or replacement process. Such Products and parts will be comparable in function and
performance to an original Product or part and warranted for the remainder of the original
warranty period.
WHITE
GROUND
(bare)
WIRING PLATE
How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify
the Company at the address or telephone number stated below within seven (7) days of
discovering the covered defect, (b) give the model number and part identification and
(c) describe the nature of any defect in the Product or part. At the time of requesting warranty
service, you must present evidence of the original purchase date. If you cannot provide a
copy of the original written limited warranty, then the terms of the Company’s most current
written limited warranty for your particular product will control. The most current limited
written warranties for the Company’s products can be found at www.broan.com.
Broan-NuTone LLC 926 West State Street, Hartford, WI 53027
www.broan.com 800-637-1453 www.nutone.com 888-336-3948
Broan-NuTone Canada ULC 1140 Tristar Drive, Mississauga, Ontario L5T 1H9
www.broan.ca www.nutone.ca 888-882-7626
120 VAC LINE IN
99045548C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement