Rust-Oleum 266295 1 gal. Penetrating Concrete Sealer Manual

Rust-Oleum 266295 1 gal. Penetrating Concrete Sealer Manual
TECHNICAL DATA
ROC-03
PENETRATING CONCRETE SEALER
DESCRIPTION AND USES
.
..PRODUCT APPLICATION
®
Rust-Oleum Penetrating Concrete Sealer provides excellent
protection from the damaging effects of water, oil, chemicals, and
stains to help extend the life of concrete. Rust-Oleum Penetrating
Concrete Sealer seeps deep into concrete pores to form a
protective barrier beneath the surface. The durable barrier repels
water and water-borne salt preventing common concrete
problems (pitting, spalled, and dusting) also provides protection
against automotive oil and hydraulic fluids. Rust-Oleum
Penetrating Concrete Sealer is designed for use on bare
concrete and masonry surfaces such as driveways, patios,
walkways, landscaping blocks, and pavers. Do not use on
stained concrete.
SURFACE PREPARATION (cont.)
.PRODUCTS
APPLICATION
SKU
266295
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
.
Rust-Oleum Penetrating Concrete Sealer is ready to use. Apply
only when air, material, and surface temperatures are between
60-85°F (15-29°C) and the surface temperature is at least 5°F
(3°C) above the dew point. The relative humidity should not be
greater than 85%. The minimum floor temperature for painting is
55°F (13°C). Pour a portion of the material into a lined paint pan.
Immediately begin to cut in the perimeter of the floor along the
wall, or other areas where a roller cannot reach, using a brush or
edger before beginning roller application. Use a synthetic ⅜” nap
roller cover on a 9" roller frame to apply an even coat of
Penetrating Concrete Sealer onto the surface. Limit the
application to 4x4 foot (1.2x1.2m) sections at a time. Maintain a
wet edge to prevent lap marks and gloss variations. Make all final
passes in the same direction to ensure uniform appearance.
Description
Penetrating Sealer (1-Gallon)
..PRODUCT APPLICATION
.
.
SURFACE PREPARATION
Allow new concrete to cure for a minimum of 28 days. Do not
use on asphalt. Remove any oil spots, grease, or spills and wash
the floor with a suitable detergent or degreasing solution.
Thoroughly rinse with fresh water. Then etch the floor using
Rust-Oleum® Concrete Etch. Note: If the concrete is not
completely rinsed, the sealer may not properly penetrate
the concrete.
If the floor is sealed, the sealer will have to be removed by
grinding or shot blasting. To determine if a concrete sealer is
present, drip a small amount of water onto various areas on the
surface. If the water beads up, a sealer is present and
Penetrating Concrete Sealer cannot be used.
CLEAN-UP
When finished, wash tools and equipment with warm
water. Properly dispose of all soiled rags and protect
unused product from freezing.
Previously Coated Floors - Penetrating Concrete Sealer
cannot be used on previously painted floors. If the floor is
previously painted, all paint must be removed prior to
sealing.
1
Form: GDH-518
Rev.: 101716
TECHNICAL DATA
PENETRATING CONCRETE SEALER
PHYSICAL PROPERTIES
.
PENETRATING CONCRETE SEALER
Resin Type
Proprietary Water-Based Polymer
Pigment Type
None
Solvents
Weight
Solids
Glycol Ethers, Water
Per Gallon
8.33 lbs
Per Liter
1.00 kg
By Weight
Proprietary
By Volume
Proprietary
Volatile Organic Compounds
<15 g/l (0.12 lbs./gal.)
Recommended Dry Film Thickness
(DFT) Per coat
Penetrating Sealer – No Surface Film
Wet Film to Achieve DFT
2 Saturating Coats
250-700 sq.ft./gal. (6.2-9.17.2 m2/l)
depending on concrete porosity
Practical Coverage at Recommended
DFT (assumes 15% material loss)
Dry Times at 70-80°F
(21-27°C) and 50%
Relative Humidity
Walk Ready
2 hours
Recoat
Optional: From when surface wetness disappears and up to 2 days
Drive Ready
12 hours
Shelf Life
2 years
Flash Point
>200ºF (93ºC)
Safety Information
For additional information, see SDS
* Calculated values may vary slightly from the actual manufactured material.
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature
do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we
can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All
technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-518
Rev.: 101716
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement